Re: [PATCH 24/26] dt-bindings: Document img,boston-clock binding

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 26/08/16 18:44, Stephen Boyd wrote:
> On 08/26, Paul Burton wrote:
>> diff --git a/Documentation/devicetree/bindings/clock/img,boston-clock.txt b/Documentation/devicetree/bindings/clock/img,boston-clock.txt
>> new file mode 100644
>> index 0000000..c01ea60
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/clock/img,boston-clock.txt
>> @@ -0,0 +1,27 @@
>> +Binding for Imagination Technologies MIPS Boston clock sources.
>> +
>> +This binding uses the common clock binding[1].
>> +
>> +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
>> +
>> +Required properties:
>> +- compatible : Should be "img,boston-clock".
>> +- #clock-cells : Should be set to 1.
>> +  Values available for clock consumers can be found in the header file:
>> +    <dt-bindings/clock/boston-clock.h>
>> +- regmap : Phandle to the Boston platform register system controller.
>> +  This should contain a phandle to the system controller node covering the
>> +  platform registers provided by the Boston board.
>> +
>> +Example:
>> +
>> +	clk_boston: clock {
>> +		compatible = "img,boston-clock";
>> +		#clock-cells = <1>;
>> +		regmap = <&plat_regs>;
> 
> Isn't syscon more standard than regmap as the property name? Is
> there a binding for the plat_regs device? Is there any reason the
> clks can't be populated in that syscon driver?

Hi Stephen,

The plat_regs device doesn't have a custom driver, it simply makes use
of the generic "syscon" driver which can provide a regmap.

It would be possible to register the clocks from a register for the
plat_regs device, but I don't think it would make much sense. The
platform registers in question are essentially just a convenient place
where various bits of information about the system are exposed,
including the clock frequencies but also other bits & pieces like
connectivity of PCIe controllers or I/O coherence units, the RTL
revision of the CPU or the wrapper RTL that runs on this FPGA-based
board, a register that allows for resetting the board, etc. It's not a
single piece of hardware, more a dumping ground for miscellanea. So in
my opinion using the syscon approach works best here, and drivers for
well defined pieces of hardware or functionality can reference that
syscon to retrieve the regmap.

As for whether "syscon" is a more standard property name than "regmap",
both seem to be used based on a grep of
Documentation/devicetree/bindings/. I believe I picked up use of
"regmap" from the generic syscon-poweroff & syscon-reboot drivers, which
both use "regmap" as a property name.

Thanks,
    Paul

> 
>> +	};
>> +
>> +	uart0: uart@17ffe000 {
>> +		/* ... */
>> +		clocks = <&clk_boston BOSTON_CLK_SYS>;
>> +	};
> 
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux