Hi,
On 06/14/2016 03:19 PM, Chen-Yu Tsai wrote:
On Tue, Jun 14, 2016 at 8:59 PM, Quentin Schulz
<quentin.schulz@xxxxxxxxxxxxxxxxxx> wrote:
Hi,
On 13/06/2016 15:04, Chen-Yu Tsai wrote:
Hi,
On Mon, Jun 13, 2016 at 6:15 PM, Quentin Schulz
<quentin.schulz@xxxxxxxxxxxxxxxxxx> wrote:
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of NAND, 512MB of RAM, USB host
You say NAND here, but you enable mmc2 for eMMC below. Please correct it.
ACK.
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
I assume the board is this one:
https://world.taobao.com/item/530374411673.htm
Definitely looks like it.
Signed-off-by: Quentin Schulz <quentin.schulz@xxxxxxxxxxxxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-r16-parrot.dts | 333 +++++++++++++++++++++++++++++++++
2 files changed, 334 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-r16-parrot.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 06b6c2d..1149512 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -760,6 +760,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-ippo-q8h-v1.2.dtb \
sun8i-a33-q8-tablet.dtb \
sun8i-a33-sinlinx-sina33.dtb \
+ sun8i-r16-parrot.dtb \
sun8i-a83t-allwinner-h8homlet-v2.dtb \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-h3-orangepi-2.dtb \
diff --git a/arch/arm/boot/dts/sun8i-r16-parrot.dts b/arch/arm/boot/dts/sun8i-r16-parrot.dts
new file mode 100644
index 0000000..75e2420
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r16-parrot.dts
@@ -0,0 +1,333 @@
+/*
+ * Copyright 2015 Quentin Schulz
+ *
+ * Quentin Schulz <quentin.schulz@xxxxxxxxxxxxxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a33.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Allwinner Parrot EVB R16";
+ compatible = "allwinner,parrot-evb-r16", "allwinner,sun8i-a33";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_r16>;
IMO r16 is too generic. You may want to add parrot_ or parrot_evb_ to it.
Same goes for all the other r16 identifier names.
ACK.
+
+ led1 {
+ label = "r16:led1:usr";
+ gpio = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */
+ };
+
+ led2 {
+ label = "r16:led2:usr";
+ gpio = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
+ };
+
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
Nothing connected? A comment mentioning which connector this is on
if it's not directly connecting something on the board would be nice.
An accelerometer is connected to this i2c, but:
1) The given address of the i2c device given by i2cdetect is not the
same as specified in both fex and schematics.
2) The accelerometer has a "product reference" on the schematics for a
Broadcom BMA250 but the associated driver does not work with it.
So there is an accelerometer connected to this i2c but I've not found
yet what can drive it. I could add a comment specifying the
accelerometer is attached to this i2c or remove the node?
A comment will suffice, until you figure out what exactly is on there.
+};
+
+&lradc {
+ vref-supply = <®_aldo3>;
+ status = "okay";
+
+ button@0 {
+ label = "V+";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <190000>;
+ };
+
+ button@1 {
+ label = "V-";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <390000>;
+ };
+
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_parrot>;
+ vmmc-supply = <®_dcdc1>;
+ cd-gpios = <&pio 3 14 GPIO_ACTIVE_LOW>; /* PD14 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>, <&wifi_reset_pin_r16>;
+ vmmc-supply = <®_aldo1>;
This looks fishy. See below.
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&mmc2_8bit_pins {
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&pio {
+ mmc0_cd_pin_parrot: mmc0_cd_pin@0 {
_parrot suffix works as well.
+ allwinner,pins = "PD14";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ led_pins_r16: led_pins@0 {
+ allwinner,pins = "PE16", "PE17";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_id_det: usb0_id_detect_pin@0 {
+ allwinner,pins = "PD10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ usb1_vbus_pin_r16: usb1_vbus_pin@0 {
+ allwinner,pins = "PD12";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ wifi_reset_pin_r16: wifi_reset_pin@3 {
Why @3?
This is a typo, I'll correct it.
+ allwinner,pins = "PL6";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
A drivevbus-supply referencing reg_vcc5v0 here would be better.
ACK.
+ x-powers,drive-vbus-en;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "aldo1";
What is this for exactly? Would turning it off render the system inoperable?
How was it referenced in the fex file?
If this is for WiFi I/O VCC, then you should specify it in mmc1 with
vqmmc-supply.
In the fex, aldo1 is one of the three power inputs for the WiFi (the
others being dldo1 and dldo2) and in the schematics it is linked to
both VCC-USB and VCC-IO-WIFI.
I tried to turn it off and, indeed, the system becomes inoperable.
I'll add vqmmc-supply in mmc1 with aldo1 regulator. However, I am
wondering what to put in vmmc-supply for mmc1 since the WiFi module has
three power inputs: dldo1, dldo2 and aldo1. In the fex, they are
referenced as, respectively, module_power1, module_power2 and
module_power3 and in the schematics dldo1 and dldo2 are named VCC-WIFI
while aldo1 is used for VCC-IO-WIFI (if it can help in any way).
VCC-WIFI is connected to pin VBAT of the Broadcom AP6212 WiFi chip.
VCC-IO-WIFI is connected to pin VDDIO of the chip.
VCC-IO-WIFI is vqmmc, and VCC-WIFI is vmmc.
About having 2 regulators, Maxime is working on a solution. In the
meantime, you could have dldo1/dldo2 always-on, and put a TODO
comment on them.
Not sure about it also linked to VCC-USB though. Is VCC-USB connected
to the SoC or just a trace on the board? If it's the latter, it might
also be designed to work with a USB based WiFi module.
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-always-on;
A comment saying why this is always on would be nice.
I assume this is and dldo2 are waiting on regulator supply list support.
dldo1 and dldo2 are not always on. It is a mistake on my side. Certainly
left after quick debugging sessions for the WiFi.
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_dldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi1";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0-csi";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+®_eldo2 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "dsp-vcc";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "eldo3";
Is this connected or used? If not you could just omit it.
eldo3 is connected to a single GPIO.
Any idea what it's used for?
+};
+
+®_usb1_vbus {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_vbus_pin_r16>;
+ gpio = <&pio 3 12 GPIO_ACTIVE_HIGH>; /* PD12 */
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_b>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_det>;
+ usb0_vbus-supply = <®_drivevbus>;
+ usb0_id_det-gpios = <&pio 3 10 GPIO_ACTIVE_HIGH>; /* PD10 */
No vbus detect or vbus-power-supply? Though IIRC it still works, just slower.
Adding "usb0_vbus_power-supply = <&usb_power_suply>;" (and setting
status of usb_power_supply to okay) makes the micro USB port not
detecting USB cable plugged in (in host or peripheral mode).
(CC-ing Hans)
There are some fixes for this, though they might not have landed.
Right, I do not know which tree you are using, but the usb_power_supply support
for the axp221 / axp223 has not landed upstream yet, nor is it in
linux-sunxi/sunxi-next. The patches have been accepted by lee, but he has not
yet pushed them to next.
For now you can try:
https://github.com/jwrdegoede/linux-sunxi/commits/sunxi-wip
Which has all the necessary commits.
With that kernel tree the "usb0_vbus_power-supply = <&usb_power_suply>;"
should work, and all necessary bits are on their way to next,
there just not all there yet.
Regards,
Hans
In the fex, the vbus_det-gpio is "apx_ctrl", I guess this means we don't
have a GPIO for vbus detection?
Yeah. This means we're using the PMIC's VBUS sensing function.
Regards
ChenYu
Thanks!
Regards,
Quentin
Regards,
ChenYu
+ usb1_vbus-supply = <®_usb1_vbus>; /* USB1 VBUS is always on */
+};
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
