On Tue, 7 Jun 2016 00:06:45 +0300 Aleksei Mamlin <mamlinav@xxxxxxxxx> wrote: > On Mon, 6 Jun 2016 22:31:38 +0200 > Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx> wrote: > > > On Mon, 6 Jun 2016 22:59:03 +0300 > > Aleksei Mamlin <mamlinav@xxxxxxxxx> wrote: > > > > > On Mon, 6 Jun 2016 20:55:49 +0200 > > > Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx> wrote: > > > > > > > On Mon, 6 Jun 2016 13:24:22 +0300 > > > > Aleksei Mamlin <mamlinav@xxxxxxxxx> wrote: > > > > > > > > > Add the full description of the Hynix H27UBG8T2BTR-BC NAND chip in the > > > > > nand_ids table so that we can later use the NAND ECC infos and ONFI timings > > > > > mode in controller drivers. > > > > > > > > Still hoping to get this series [1] merged in 4.8, but if that's > > > > not the case, I'll apply your patch. > > > > > > > > BTW, that would be great if you could test it on your platforms. > > > > > > > > > > It seems that Hynix-specific initialization code can't handle H27UBG8T2BTR-BC > > > chip: > > > > > > [ 0.886153] nand: Could not find valid ONFI parameter page; aborting > > > [ 0.892665] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xd7 > > > [ 0.899025] nand: Hynix 1c03000.nand > > > [ 0.902596] nand: bus width 8 instead 16 bit > > > [ 0.906858] nand: No NAND device found > > > [ 0.910620] sunxi_nand 1c03000.nand: failed to init nand chips > > > [ 0.916528] sunxi_nand: probe of 1c03000.nand failed with error -22 > > > > Can you try this patch? It should fix the problem [1]. > > > > [1]http://code.bulix.org/6hjww1-100494 > > > > Yes, it fixes problem. What about ONFI parameter page? Should it be ignored? It should be ignored: your NAND is not 'ONFI compatible', the datasheet just says that it supports the' ONFI command set', which is not the same :). The trace you're seeing here is just notifying that the core failed to detect an ONFI NAND, which is expected in your case. > [ 0.886068] nand: Could not find valid ONFI parameter page; aborting > [ 0.892571] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xd7 > [ 0.898917] nand: Hynix NAND 4GiB 3,3V 8-bit > [ 0.903198] nand: 4096 MiB, MLC, erase size: 2048 KiB, page size: 8192, OOB size: 640 > [ 0.911908] Bad block table found at page 524032, version 0x01 > [ 0.918534] Bad block table found at page 523776, version 0x01 > [ 0.972112] 5 ofpart partitions found on MTD device 1c03000.nand > [ 0.978116] Creating 5 MTD partitions on "1c03000.nand": > [ 0.983477] 0x000000000000-0x000000200000 : "boot0" > [ 0.988803] 0x000000200000-0x000000400000 : "boot0-rescue" > [ 0.994692] 0x000000400000-0x000000600000 : "uboot" > [ 0.999944] 0x000000600000-0x000000800000 : "uboot-rescue" > [ 1.005763] 0x000000800000-0x000100000000 : "main" > > > > > -- > > Boris Brezillon, Free Electrons > > Embedded Linux and Kernel engineering > > http://free-electrons.com > > -- Boris Brezillon, Free Electrons Embedded Linux and Kernel engineering http://free-electrons.com -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
