Hi, On 03-06-16 03:38, Chen-Yu Tsai wrote:
Hi, On Fri, Jun 3, 2016 at 1:18 AM, Hans de Goede <hdegoede@xxxxxxxxxx> wrote:The axp20x pmics have 2 power inputs, one called ACIN which is intended for to be supplied via a powerbarrel on the board and one called VBUS which is intended to be supplied via an otg connector. In the VBUS case the pmic needs to know if the board is supplying power to the otg connector, because then it should not take any power from its VBUS pin. The axp209 pmic has a N_VBUSEN input pin via which the board can signal to the pmic whether the board is supplying power to the otg connector or not. On the axp221/axp223 this pin can alternatively be used as an output which controls an external regulator which (optionally) supplies power to the otg connector from the board. When the pin is used as output it is called DRIVEVBUS in the datasheet. This commit adds support for the DRIVEVBUS pin as an extra pmic controlled regulator. Since this is optional a new x-powers,drivebus dt property is added. When this is present the misc-control register is written to change the N_VBUSEN input pin to DRIVEVBUS output pin mode and the extra drivebus regulator is registered with the regulator subsystem. Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> --- Changes in v2: -Rename the dt property to drive-vbus-en -s/drivebus/drivevbus/ -Add a line describing the drivevbus regulator to the table in Documentation/devicetree/bindings/mfd/axp20x.txt -Set supply_name to drivevbus-supply --- Documentation/devicetree/bindings/mfd/axp20x.txt | 6 +++++ drivers/regulator/axp20x-regulator.c | 30 ++++++++++++++++++++++++ 2 files changed, 36 insertions(+) diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index d20b103..6aca4fe 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -22,6 +22,11 @@ Optional properties: AXP152/20X: range: 750-1875, Default: 1.5 MHz AXP22X/80X: range: 1800-4050, Default: 3 MHz +- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the + N_VBUSEN pin is used as an output pin to control an external + regulator to drive the OTG VBus, rather then as an input pin + which signals whether the board is driving OTG VBus or not.Git complains about space indentation here.+ - <input>-supply: a phandle to the regulator supply node. May be omitted if inputs are unregulated, such as using the IPSOUT output from the PMIC. @@ -79,6 +84,7 @@ ELDO3 : LDO : eldoin-supply : shared supply LDO_IO0 : LDO : ips-supply : GPIO 0 LDO_IO1 : LDO : ips-supply : GPIO 1 RTC_LDO : LDO : ips-supply : always on +DRIVEVBUS : Enable output : drivevbus-supply : external regulator AXP809 regulators, type, and corresponding input supply names: diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c index 728be64..3f1bba4 100644 --- a/drivers/regulator/axp20x-regulator.c +++ b/drivers/regulator/axp20x-regulator.c @@ -36,6 +36,8 @@ #define AXP20X_FREQ_DCDC_MASK 0x0f +#define AXP22X_MISC_N_VBUSEN_FUNC BIT(4) + #define AXP_DESC_IO(_family, _id, _match, _supply, _min, _max, _step, _vreg, \ _vmask, _ereg, _emask, _enable_val, _disable_val) \ [_family##_##_id] = { \ @@ -230,6 +232,18 @@ static const struct regulator_desc axp22x_regulators[] = { AXP_DESC_FIXED(AXP22X, RTC_LDO, "rtc_ldo", "ips", 3000), }; +static const struct regulator_desc axp22x_drivevbus_regulator = { + .name = "drivevbus", + .supply_name = "drivevbus-supply",The "-supply" suffix is added by the regulator core upon lookup. No need to add it here. I assume the regulator core won't get confused over a supply name that's the same as the regulator requesting it. Otherwise, Acked-by: Chen-Yu Tsai <wens@xxxxxxxx>
Thanks, I'll send a v3 with both issues fixed. Regards, Hans
+ .of_match = of_match_ptr("drivevbus"), + .regulators_node = of_match_ptr("regulators"), + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, + .enable_reg = AXP20X_VBUS_IPSOUT_MGMT, + .enable_mask = BIT(2), + .ops = &axp20x_ops_sw, +}; + static const struct regulator_linear_range axp809_dcdc4_ranges[] = { REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2f, 20000), REGULATOR_LINEAR_RANGE(1800000, 0x30, 0x38, 100000), @@ -411,6 +425,7 @@ static int axp20x_regulator_probe(struct platform_device *pdev) u32 workmode; const char *dcdc1_name = axp22x_regulators[AXP22X_DCDC1].name; const char *dcdc5_name = axp22x_regulators[AXP22X_DCDC5].name; + bool drivevbus = false; switch (axp20x->variant) { case AXP202_ID: @@ -422,6 +437,8 @@ static int axp20x_regulator_probe(struct platform_device *pdev) case AXP223_ID: regulators = axp22x_regulators; nregulators = AXP22X_REG_ID_MAX; + drivevbus = of_property_read_bool(pdev->dev.parent->of_node, + "x-powers,drive-vbus-en"); break; case AXP809_ID: regulators = axp809_regulators; @@ -500,6 +517,19 @@ static int axp20x_regulator_probe(struct platform_device *pdev) &dcdc5_name); } + if (drivevbus) { + /* Change N_VBUSEN sense pin to DRIVEVBUS output pin */ + regmap_update_bits(axp20x->regmap, AXP20X_OVER_TMP, + AXP22X_MISC_N_VBUSEN_FUNC, 0); + rdev = devm_regulator_register(&pdev->dev, + &axp22x_drivevbus_regulator, + &config); + if (IS_ERR(rdev)) { + dev_err(&pdev->dev, "Failed to register drivevbus\n"); + return PTR_ERR(rdev); + } + } + return 0; } -- 2.7.4
-- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
