Hi,
On Fri, Jun 3, 2016 at 1:18 AM, Hans de Goede <hdegoede@xxxxxxxxxx> wrote:
> The axp20x pmics have 2 power inputs, one called ACIN which is intended
> for to be supplied via a powerbarrel on the board and one called VBUS
> which is intended to be supplied via an otg connector.
>
> In the VBUS case the pmic needs to know if the board is supplying power
> to the otg connector, because then it should not take any power from
> its VBUS pin. The axp209 pmic has a N_VBUSEN input pin via which the
> board can signal to the pmic whether the board is supplying power to the
> otg connector or not.
>
> On the axp221/axp223 this pin can alternatively be used as an output
> which controls an external regulator which (optionally) supplies
> power to the otg connector from the board. When the pin is used as
> output it is called DRIVEVBUS in the datasheet.
>
> This commit adds support for the DRIVEVBUS pin as an extra pmic
> controlled regulator. Since this is optional a new x-powers,drivebus dt
> property is added. When this is present the misc-control register is
> written to change the N_VBUSEN input pin to DRIVEVBUS output pin mode and
> the extra drivebus regulator is registered with the regulator subsystem.
>
> Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx>
> ---
> Changes in v2:
> -Rename the dt property to drive-vbus-en
> -s/drivebus/drivevbus/
> -Add a line describing the drivevbus regulator to the table in
> Documentation/devicetree/bindings/mfd/axp20x.txt
> -Set supply_name to drivevbus-supply
> ---
> Documentation/devicetree/bindings/mfd/axp20x.txt | 6 +++++
> drivers/regulator/axp20x-regulator.c | 30 ++++++++++++++++++++++++
> 2 files changed, 36 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt
> index d20b103..6aca4fe 100644
> --- a/Documentation/devicetree/bindings/mfd/axp20x.txt
> +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt
> @@ -22,6 +22,11 @@ Optional properties:
> AXP152/20X: range: 750-1875, Default: 1.5 MHz
> AXP22X/80X: range: 1800-4050, Default: 3 MHz
>
> +- x-powers,drive-vbus-en: axp221 / axp223 only boolean, set this when the
> + N_VBUSEN pin is used as an output pin to control an external
> + regulator to drive the OTG VBus, rather then as an input pin
> + which signals whether the board is driving OTG VBus or not.
Git complains about space indentation here.
> +
> - <input>-supply: a phandle to the regulator supply node. May be omitted if
> inputs are unregulated, such as using the IPSOUT output
> from the PMIC.
> @@ -79,6 +84,7 @@ ELDO3 : LDO : eldoin-supply : shared supply
> LDO_IO0 : LDO : ips-supply : GPIO 0
> LDO_IO1 : LDO : ips-supply : GPIO 1
> RTC_LDO : LDO : ips-supply : always on
> +DRIVEVBUS : Enable output : drivevbus-supply : external regulator
>
> AXP809 regulators, type, and corresponding input supply names:
>
> diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
> index 728be64..3f1bba4 100644
> --- a/drivers/regulator/axp20x-regulator.c
> +++ b/drivers/regulator/axp20x-regulator.c
> @@ -36,6 +36,8 @@
>
> #define AXP20X_FREQ_DCDC_MASK 0x0f
>
> +#define AXP22X_MISC_N_VBUSEN_FUNC BIT(4)
> +
> #define AXP_DESC_IO(_family, _id, _match, _supply, _min, _max, _step, _vreg, \
> _vmask, _ereg, _emask, _enable_val, _disable_val) \
> [_family##_##_id] = { \
> @@ -230,6 +232,18 @@ static const struct regulator_desc axp22x_regulators[] = {
> AXP_DESC_FIXED(AXP22X, RTC_LDO, "rtc_ldo", "ips", 3000),
> };
>
> +static const struct regulator_desc axp22x_drivevbus_regulator = {
> + .name = "drivevbus",
> + .supply_name = "drivevbus-supply",
The "-supply" suffix is added by the regulator core upon lookup. No need
to add it here. I assume the regulator core won't get confused over a
supply name that's the same as the regulator requesting it.
Otherwise,
Acked-by: Chen-Yu Tsai <wens@xxxxxxxx>
> + .of_match = of_match_ptr("drivevbus"),
> + .regulators_node = of_match_ptr("regulators"),
> + .type = REGULATOR_VOLTAGE,
> + .owner = THIS_MODULE,
> + .enable_reg = AXP20X_VBUS_IPSOUT_MGMT,
> + .enable_mask = BIT(2),
> + .ops = &axp20x_ops_sw,
> +};
> +
> static const struct regulator_linear_range axp809_dcdc4_ranges[] = {
> REGULATOR_LINEAR_RANGE(600000, 0x0, 0x2f, 20000),
> REGULATOR_LINEAR_RANGE(1800000, 0x30, 0x38, 100000),
> @@ -411,6 +425,7 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
> u32 workmode;
> const char *dcdc1_name = axp22x_regulators[AXP22X_DCDC1].name;
> const char *dcdc5_name = axp22x_regulators[AXP22X_DCDC5].name;
> + bool drivevbus = false;
>
> switch (axp20x->variant) {
> case AXP202_ID:
> @@ -422,6 +437,8 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
> case AXP223_ID:
> regulators = axp22x_regulators;
> nregulators = AXP22X_REG_ID_MAX;
> + drivevbus = of_property_read_bool(pdev->dev.parent->of_node,
> + "x-powers,drive-vbus-en");
> break;
> case AXP809_ID:
> regulators = axp809_regulators;
> @@ -500,6 +517,19 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
> &dcdc5_name);
> }
>
> + if (drivevbus) {
> + /* Change N_VBUSEN sense pin to DRIVEVBUS output pin */
> + regmap_update_bits(axp20x->regmap, AXP20X_OVER_TMP,
> + AXP22X_MISC_N_VBUSEN_FUNC, 0);
> + rdev = devm_regulator_register(&pdev->dev,
> + &axp22x_drivevbus_regulator,
> + &config);
> + if (IS_ERR(rdev)) {
> + dev_err(&pdev->dev, "Failed to register drivevbus\n");
> + return PTR_ERR(rdev);
> + }
> + }
> +
> return 0;
> }
>
> --
> 2.7.4
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
