Re: [PATCH v6 2/3] Documentation: gpio: Update description for X-Gene standby GPIO controller DTS binding

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 15/02/16 04:57, Quan Nguyen wrote:
> Update description for X-Gene standby GPIO controller DTS binding to
> support GPIO line configuration as input, output or external IRQ pin.
> 
> Signed-off-by: Y Vo <yvo@xxxxxxx>
> Signed-off-by: Quan Nguyen <qnguyen@xxxxxxx>
> ---
>  .../devicetree/bindings/gpio/gpio-xgene-sb.txt     | 47 ++++++++++++++++++----
>  1 file changed, 40 insertions(+), 7 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
> index dae1300..7b8b4cb 100644
> --- a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
> +++ b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
> @@ -1,10 +1,20 @@
>  APM X-Gene Standby GPIO controller bindings
>  
> -This is a gpio controller in the standby domain.
> -
> -There are 20 GPIO pins from 0..21. There is no GPIO_DS14 or GPIO_DS15,
> -only GPIO_DS8..GPIO_DS13 support interrupts. The IRQ mapping
> -is currently 1-to-1 on interrupts 0x28 thru 0x2d.
> +This is a gpio controller in the standby domain. It also supports interrupt in
> +some particular pins which are sourced to its parent interrupt controller
> +as diagram below:
> +                           +-----------------+
> +                           | X-Gene standby  |
> +                           | GPIO controller +--------- GPIO_0
> ++------------+             |                 | ...
> +| Parent IRQ |             |                 +--------- GPIO_8/EXT_INT_0
> +| controller |  EXT_INT_0  |                 | ...
> +| (GICv2)    +-------------+                 +--------- GPIO_[N+8]/EXT_INT_N
> +|            |  ...        |                 |
> +|            |  EXT_INT_N  |                 +--------- GPIO_[N+9]
> +|            +-------------+                 | ...
> +|            |             |                 +--------- GPIO_MAX
> ++------------+             +-----------------+
>  
>  Required properties:
>  - compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller
> @@ -15,10 +25,18 @@ Required properties:
>  		0 = active high
>  		1 = active low
>  - gpio-controller: Marks the device node as a GPIO controller.
> -- interrupts: Shall contain exactly 6 interrupts.
> +- interrupts: The EXT_INT_0 parent interrupt resource must be listed first.
> +- interrupt-parent: Phandle of the parent interrupt controller.
> +- interrupt-cells: Should be two.
> +       - first cell is 0-N coresponding for EXT_INT_0 to EXT_INT_N.
> +       - second cell is used to specify flags.
> +- interrupt-controller: Marks the device node as an interrupt controller.
> +- apm,nr-gpios: Optional, specify number of gpios pin.
> +- apm,nr-irqs: Optional, specify number of interrupt pins.
> +- apm,irq-start: Optional, specify lowest gpio pin support interrupt.

This is quite ambiguous. Is that relative to the GIC? Assuming this is
the case, you should then document it, specify the type of interrupt
(SPI?), and whether this is 0- or 32-based (the code seems to indicate
that is is 0-based).

>  
>  Example:
> -	sbgpio: sbgpio@17001000 {
> +	sbgpio: gpio@17001000{
>  		compatible = "apm,xgene-gpio-sb";
>  		reg = <0x0 0x17001000 0x0 0x400>;
>  		#gpio-cells = <2>;
> @@ -29,4 +47,19 @@ Example:
>  				<0x0 0x2b 0x1>,
>  				<0x0 0x2c 0x1>,
>  				<0x0 0x2d 0x1>;
> +		interrupt-parent = <&gic>;
> +		#interrupt-cells = <2>;
> +		interrupt-controller;
> +		apm,nr-gpios = <22>;
> +		apm,nr-irqs = <6>;
> +		apm,irq-start = <8>;
> +	};
> +
> +	testuser {
> +		compatible = "example,testuser";
> +		/* Use the GPIO_13/EXT_INT_5 line as an active high triggered
> +		 * level interrupt
> +		 */
> +		interrupts = <5 4>;
> +		interrupt-parent = <&sbgpio>;
>  	};
> 

Thanks,

	M.
-- 
Jazz is not dead. It just smells funny...
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux