Update description for X-Gene standby GPIO controller DTS binding to support GPIO line configuration as input, output or external IRQ pin. Signed-off-by: Y Vo <yvo@xxxxxxx> Signed-off-by: Quan Nguyen <qnguyen@xxxxxxx> --- .../devicetree/bindings/gpio/gpio-xgene-sb.txt | 47 ++++++++++++++++++---- 1 file changed, 40 insertions(+), 7 deletions(-) diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt index dae1300..7b8b4cb 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt @@ -1,10 +1,20 @@ APM X-Gene Standby GPIO controller bindings -This is a gpio controller in the standby domain. - -There are 20 GPIO pins from 0..21. There is no GPIO_DS14 or GPIO_DS15, -only GPIO_DS8..GPIO_DS13 support interrupts. The IRQ mapping -is currently 1-to-1 on interrupts 0x28 thru 0x2d. +This is a gpio controller in the standby domain. It also supports interrupt in +some particular pins which are sourced to its parent interrupt controller +as diagram below: + +-----------------+ + | X-Gene standby | + | GPIO controller +--------- GPIO_0 ++------------+ | | ... +| Parent IRQ | | +--------- GPIO_8/EXT_INT_0 +| controller | EXT_INT_0 | | ... +| (GICv2) +-------------+ +--------- GPIO_[N+8]/EXT_INT_N +| | ... | | +| | EXT_INT_N | +--------- GPIO_[N+9] +| +-------------+ | ... +| | | +--------- GPIO_MAX ++------------+ +-----------------+ Required properties: - compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller @@ -15,10 +25,18 @@ Required properties: 0 = active high 1 = active low - gpio-controller: Marks the device node as a GPIO controller. -- interrupts: Shall contain exactly 6 interrupts. +- interrupts: The EXT_INT_0 parent interrupt resource must be listed first. +- interrupt-parent: Phandle of the parent interrupt controller. +- interrupt-cells: Should be two. + - first cell is 0-N coresponding for EXT_INT_0 to EXT_INT_N. + - second cell is used to specify flags. +- interrupt-controller: Marks the device node as an interrupt controller. +- apm,nr-gpios: Optional, specify number of gpios pin. +- apm,nr-irqs: Optional, specify number of interrupt pins. +- apm,irq-start: Optional, specify lowest gpio pin support interrupt. Example: - sbgpio: sbgpio@17001000 { + sbgpio: gpio@17001000{ compatible = "apm,xgene-gpio-sb"; reg = <0x0 0x17001000 0x0 0x400>; #gpio-cells = <2>; @@ -29,4 +47,19 @@ Example: <0x0 0x2b 0x1>, <0x0 0x2c 0x1>, <0x0 0x2d 0x1>; + interrupt-parent = <&gic>; + #interrupt-cells = <2>; + interrupt-controller; + apm,nr-gpios = <22>; + apm,nr-irqs = <6>; + apm,irq-start = <8>; + }; + + testuser { + compatible = "example,testuser"; + /* Use the GPIO_13/EXT_INT_5 line as an active high triggered + * level interrupt + */ + interrupts = <5 4>; + interrupt-parent = <&sbgpio>; }; -- 1.7.12.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html