Re: [PATCH v5] mmc: OCTEON: Add host driver for OCTEON MMC controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi Rob,

On 12/02/16 15:39, Rob Herring wrote:
On Wed, Feb 10, 2016 at 05:36:15PM +0000, Matt Redfearn wrote:
From: Aleksey Makarov <aleksey.makarov@xxxxxxxxxxxxxxxxxx>

The OCTEON MMC controller is currently found on cn61XX and cnf71XX
devices.  Device parameters are configured from device tree data.

eMMC, MMC and SD devices are supported.

Tested-by: Aaro Koskinen <aaro.koskinen@xxxxxx>
Signed-off-by: Chandrakala Chavva <cchavva@xxxxxxxxxxxxxxxxxx>
Signed-off-by: David Daney <david.daney@xxxxxxxxxx>
Signed-off-by: Aleksey Makarov <aleksey.makarov@xxxxxxxxxx>
Signed-off-by: Leonid Rosenboim <lrosenboim@xxxxxxxxxxxxxxxxxx>
Signed-off-by: Peter Swain <pswain@xxxxxxxxxx>
Signed-off-by: Aaron Williams <aaron.williams@xxxxxxxxxx>
Signed-off-by: Matt Redfearn <matt.redfearn@xxxxxxxxxx>
---
v5:
Incoroprate comments from review
http://patchwork.linux-mips.org/patch/9558/
- Use standard <bus-width> property instead of <cavium,bus-max-width>.
- Use standard <max-frequency> property instead of <spi-max-frequency>.
- Add octeon_mmc_of_parse_legacy function to deal with the above
   properties, since many devices have shipped with those properties
   embedded in firmware.
- Allow the <vmmc-supply> binding in addition to the legacy
   <gpios-power>.
- Remove the secondary driver for each slot.
- Use core gpio cd/wp handling

Tested on Rhino labs UTM8, Cavium CN7130.

For reference, the binding in the shipped devices is:
mmc: mmc@1180000002000 {
	compatible = "cavium,octeon-6130-mmc";
	reg = <0x11800 0x00002000 0x0 0x100>,
		<0x11800 0x00000168 0x0 0x20>;
	#address-cells = <1>;
	#size-cells = <0>;
	/* EMM irq, DMA irq */
	interrupts = <1 19>, <0 63>;

	/* The board only has a single MMC slot */
	mmc-slot@2 {
		compatible = "cavium,octeon-6130-mmc-slot";
		reg = <2>;
		voltage-ranges = <3300 3300>;
		spi-max-frequency = <26000000>;
		/* Power on GPIO 8, active high */
		/* power-gpios = <&gpio 8 0>; */
		power-gpios = <&gpio 8 1>;

	/*      spi-max-frequency = <52000000>; */
		/* bus width can be 1, 4 or 8 */
		cavium,bus-max-width = <8>;
	};
	mmc-slot@0 {
		compatible = "cavium,octeon-6130-mmc-slot";
		reg = <0>;
		voltage-ranges = <3300 3300>;
		spi-max-frequency = <26000000>;
		/* non-removable; */
		bus-width = <8>;
		/* bus width can be 1, 4 or 8 */
		cavium,bus-max-width = <8>;
	};
};

v3:
https://lkml.kernel.org/g/<1425567033-31236-1-git-send-email-aleksey.makarov@xxxxxxxxxx>

Changes in v4:
- The sparse error discovered by Aaro Koskinen has been fixed
- Other sparse warnings have been silenced

Changes in v3:
- Rebased to v4.0-rc2
- Use gpiod_*() functions instead of legacy gpio
- Cosmetic changes

Changes in v2: All the fixes suggested by Mark Rutland were implemented:
- Device tree parsing has been fixed
- Device tree docs have been fixed
- Comment about errata workaroud has been added
---
  .../devicetree/bindings/mmc/octeon-mmc.txt         |   80 ++
  drivers/mmc/host/Kconfig                           |   10 +
  drivers/mmc/host/Makefile                          |    1 +
  drivers/mmc/host/octeon_mmc.c                      | 1409 ++++++++++++++++++++
  4 files changed, 1500 insertions(+)
  create mode 100644 Documentation/devicetree/bindings/mmc/octeon-mmc.txt
  create mode 100644 drivers/mmc/host/octeon_mmc.c

diff --git a/Documentation/devicetree/bindings/mmc/octeon-mmc.txt b/Documentation/devicetree/bindings/mmc/octeon-mmc.txt
new file mode 100644
index 000000000000..a1b20753172f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/octeon-mmc.txt
@@ -0,0 +1,80 @@
+* OCTEON SD/MMC Host Controller
+
+This controller is present on some members of the Cavium OCTEON SoC
+family, provide an interface for eMMC, MMC and SD devices.  There is a
+single controller that may have several "slots" connected.  These
+slots appear as children of the main controller node.
+The DMA engine is an integral part of the controller block.
+
+1) MMC node
+
+Required properties:
+- compatible : Should be "cavium,octeon-6130-mmc" or "cavium,octeon-7890-mmc"
+- reg : Two entries:
+	1) The base address of the MMC controller register bank.
+	2) The base address of the MMC DMA engine register bank.
+- interrupts :
+	For "cavium,octeon-6130-mmc": two entries:
+	1) The MMC controller interrupt line.
+	2) The MMC DMA engine interrupt line.
+	For "cavium,octeon-7890-mmc": nine entries:
+	1) The next block transfer of a multiblock transfer has completed (BUF_DONE)
+	2) Operation completed successfully (CMD_DONE).
+	3) DMA transfer completed successfully (DMA_DONE).
+	4) Operation encountered an error (CMD_ERR).
+	5) DMA transfer encountered an error (DMA_ERR).
+	6) Switch operation completed successfully (SWITCH_DONE).
+	7) Switch operation encountered an error (SWITCH_ERR).
+	8) Internal DMA engine request completion interrupt (DONE).
+	9) Internal DMA FIFO underflow (FIFO).
Why do h/w designers think doing this speeds up interrupt handling...

I know, right? :-/

+- #address-cells : Must be <1>
+- #size-cells : Must be <0>
+
+The node contains child nodes for each slot that the platform uses.
+
+Example:
+mmc@1180000002000 {
+	compatible = "cavium,octeon-6130-mmc";
+	reg = <0x11800 0x00002000 0x0 0x100>,
+		<0x11800 0x00000168 0x0 0x20>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	/* EMM irq, DMA irq */
+	interrupts = <1 19>, <0 63>;
+
+	[ child node definitions...]
+};
+
+
+2) Slot nodes
+Properties in mmc.txt apply to each slot node that the platform uses.
+
+Required properties:
+- reg : The slot number.
+
+Optional properties:
+- cavium,cmd-clk-skew : the amount of delay (in pS) past the clock edge
+	to sample the command pin.
+- cavium,dat-clk-skew : the amount of delay (in pS) past the clock edge
+	to sample the data pin.
Are you trying to maintain compatibility with legacy bindings here? If
not, append units (-ps).

Yes, we're trying to maintain compatibility, but should be able to accept either form, with the "-ps" version being the binding documented.


+
+Example:
+	mmc@1180000002000 {
+		compatible = "cavium,octeon-6130-mmc";
+		reg = <0x11800 0x00002000 0x0 0x100>,
+		      <0x11800 0x00000168 0x0 0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* EMM irq, DMA irq */
+		interrupts = <1 19>, <0 63>;
+
+		/* The board only has a single MMC slot */
+		mmc-slot@0 {
Most mmc bindings don't separately describe the slot. This is probably
a more correct h/w description, but then again I've never seen more than
1 slot.

The OCTEON MMC controller supports up to 4 slots of MMC, eMMC or SD types. The board I have (a Rhino Labs UTM8) has both a uSD card slot and eMMC device connected to the controller - the best way to describe this is via multiple slot nodes as children of the controller.


Otherwise, this looks fine to me.

Thanks,
Matt


+			reg = <0>;
+			max-frequency = <20000000>;
+			bus-width = <8>;
+			vmmc-supply = <&reg_vmmc3>;
+			cd-gpios = <&gpio 9 0>;
+			wp-gpios = <&gpio 10 0>;
+		};
+	};

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux