On Wed, Feb 10, 2016 at 05:36:15PM +0000, Matt Redfearn wrote: > From: Aleksey Makarov <aleksey.makarov@xxxxxxxxxxxxxxxxxx> > > The OCTEON MMC controller is currently found on cn61XX and cnf71XX > devices. Device parameters are configured from device tree data. > > eMMC, MMC and SD devices are supported. > > Tested-by: Aaro Koskinen <aaro.koskinen@xxxxxx> > Signed-off-by: Chandrakala Chavva <cchavva@xxxxxxxxxxxxxxxxxx> > Signed-off-by: David Daney <david.daney@xxxxxxxxxx> > Signed-off-by: Aleksey Makarov <aleksey.makarov@xxxxxxxxxx> > Signed-off-by: Leonid Rosenboim <lrosenboim@xxxxxxxxxxxxxxxxxx> > Signed-off-by: Peter Swain <pswain@xxxxxxxxxx> > Signed-off-by: Aaron Williams <aaron.williams@xxxxxxxxxx> > Signed-off-by: Matt Redfearn <matt.redfearn@xxxxxxxxxx> > --- > v5: > Incoroprate comments from review > http://patchwork.linux-mips.org/patch/9558/ > - Use standard <bus-width> property instead of <cavium,bus-max-width>. > - Use standard <max-frequency> property instead of <spi-max-frequency>. > - Add octeon_mmc_of_parse_legacy function to deal with the above > properties, since many devices have shipped with those properties > embedded in firmware. > - Allow the <vmmc-supply> binding in addition to the legacy > <gpios-power>. > - Remove the secondary driver for each slot. > - Use core gpio cd/wp handling > > Tested on Rhino labs UTM8, Cavium CN7130. > > For reference, the binding in the shipped devices is: > mmc: mmc@1180000002000 { > compatible = "cavium,octeon-6130-mmc"; > reg = <0x11800 0x00002000 0x0 0x100>, > <0x11800 0x00000168 0x0 0x20>; > #address-cells = <1>; > #size-cells = <0>; > /* EMM irq, DMA irq */ > interrupts = <1 19>, <0 63>; > > /* The board only has a single MMC slot */ > mmc-slot@2 { > compatible = "cavium,octeon-6130-mmc-slot"; > reg = <2>; > voltage-ranges = <3300 3300>; > spi-max-frequency = <26000000>; > /* Power on GPIO 8, active high */ > /* power-gpios = <&gpio 8 0>; */ > power-gpios = <&gpio 8 1>; > > /* spi-max-frequency = <52000000>; */ > /* bus width can be 1, 4 or 8 */ > cavium,bus-max-width = <8>; > }; > mmc-slot@0 { > compatible = "cavium,octeon-6130-mmc-slot"; > reg = <0>; > voltage-ranges = <3300 3300>; > spi-max-frequency = <26000000>; > /* non-removable; */ > bus-width = <8>; > /* bus width can be 1, 4 or 8 */ > cavium,bus-max-width = <8>; > }; > }; > > v3: > https://lkml.kernel.org/g/<1425567033-31236-1-git-send-email-aleksey.makarov@xxxxxxxxxx> > > Changes in v4: > - The sparse error discovered by Aaro Koskinen has been fixed > - Other sparse warnings have been silenced > > Changes in v3: > - Rebased to v4.0-rc2 > - Use gpiod_*() functions instead of legacy gpio > - Cosmetic changes > > Changes in v2: All the fixes suggested by Mark Rutland were implemented: > - Device tree parsing has been fixed > - Device tree docs have been fixed > - Comment about errata workaroud has been added > --- > .../devicetree/bindings/mmc/octeon-mmc.txt | 80 ++ > drivers/mmc/host/Kconfig | 10 + > drivers/mmc/host/Makefile | 1 + > drivers/mmc/host/octeon_mmc.c | 1409 ++++++++++++++++++++ > 4 files changed, 1500 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mmc/octeon-mmc.txt > create mode 100644 drivers/mmc/host/octeon_mmc.c > > diff --git a/Documentation/devicetree/bindings/mmc/octeon-mmc.txt b/Documentation/devicetree/bindings/mmc/octeon-mmc.txt > new file mode 100644 > index 000000000000..a1b20753172f > --- /dev/null > +++ b/Documentation/devicetree/bindings/mmc/octeon-mmc.txt > @@ -0,0 +1,80 @@ > +* OCTEON SD/MMC Host Controller > + > +This controller is present on some members of the Cavium OCTEON SoC > +family, provide an interface for eMMC, MMC and SD devices. There is a > +single controller that may have several "slots" connected. These > +slots appear as children of the main controller node. > +The DMA engine is an integral part of the controller block. > + > +1) MMC node > + > +Required properties: > +- compatible : Should be "cavium,octeon-6130-mmc" or "cavium,octeon-7890-mmc" > +- reg : Two entries: > + 1) The base address of the MMC controller register bank. > + 2) The base address of the MMC DMA engine register bank. > +- interrupts : > + For "cavium,octeon-6130-mmc": two entries: > + 1) The MMC controller interrupt line. > + 2) The MMC DMA engine interrupt line. > + For "cavium,octeon-7890-mmc": nine entries: > + 1) The next block transfer of a multiblock transfer has completed (BUF_DONE) > + 2) Operation completed successfully (CMD_DONE). > + 3) DMA transfer completed successfully (DMA_DONE). > + 4) Operation encountered an error (CMD_ERR). > + 5) DMA transfer encountered an error (DMA_ERR). > + 6) Switch operation completed successfully (SWITCH_DONE). > + 7) Switch operation encountered an error (SWITCH_ERR). > + 8) Internal DMA engine request completion interrupt (DONE). > + 9) Internal DMA FIFO underflow (FIFO). Why do h/w designers think doing this speeds up interrupt handling... > +- #address-cells : Must be <1> > +- #size-cells : Must be <0> > + > +The node contains child nodes for each slot that the platform uses. > + > +Example: > +mmc@1180000002000 { > + compatible = "cavium,octeon-6130-mmc"; > + reg = <0x11800 0x00002000 0x0 0x100>, > + <0x11800 0x00000168 0x0 0x20>; > + #address-cells = <1>; > + #size-cells = <0>; > + /* EMM irq, DMA irq */ > + interrupts = <1 19>, <0 63>; > + > + [ child node definitions...] > +}; > + > + > +2) Slot nodes > +Properties in mmc.txt apply to each slot node that the platform uses. > + > +Required properties: > +- reg : The slot number. > + > +Optional properties: > +- cavium,cmd-clk-skew : the amount of delay (in pS) past the clock edge > + to sample the command pin. > +- cavium,dat-clk-skew : the amount of delay (in pS) past the clock edge > + to sample the data pin. Are you trying to maintain compatibility with legacy bindings here? If not, append units (-ps). > + > +Example: > + mmc@1180000002000 { > + compatible = "cavium,octeon-6130-mmc"; > + reg = <0x11800 0x00002000 0x0 0x100>, > + <0x11800 0x00000168 0x0 0x20>; > + #address-cells = <1>; > + #size-cells = <0>; > + /* EMM irq, DMA irq */ > + interrupts = <1 19>, <0 63>; > + > + /* The board only has a single MMC slot */ > + mmc-slot@0 { Most mmc bindings don't separately describe the slot. This is probably a more correct h/w description, but then again I've never seen more than 1 slot. Otherwise, this looks fine to me. > + reg = <0>; > + max-frequency = <20000000>; > + bus-width = <8>; > + vmmc-supply = <®_vmmc3>; > + cd-gpios = <&gpio 9 0>; > + wp-gpios = <&gpio 10 0>; > + }; > + }; -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
