On Tue, 22 Oct 2013 13:08:46 +0530, Laxman Dewangan <ldewangan@xxxxxxxxxx> wrote: > The ams AS3722 is a compact system PMU suitable for mobile phones, > tablets etc. It has 4 DC/DC step-down regulators, 3 DC/DC step-down > controller, 11 LDOs, RTC, automatic battery, temperature and > over-current monitoring, 8 GPIOs, ADC and a watchdog. > > Add MFD core driver for the AS3722 to support core functionality. > > Signed-off-by: Laxman Dewangan <ldewangan@xxxxxxxxxx> > Signed-off-by: Florian Lobmaier <florian.lobmaier@xxxxxxx> > Acked-by: Lee Jones <lee.jones@xxxxxxxxxx> > Acked-by: Stephen Warren <swarren@xxxxxxxxxx> > --- > Changes from V1: > - Remove compatible string from DT for subnode. > - Nit cleanups in driver and use module_i2c_driver > > Changes from V2: > - Change DT file to reflect the changes in gpio/pincntrl driver. > Now there is no extra subnode. > > Changes from V3: > - Combine DT of pincontrol and regulator to mfd. > - Nits cleanups. > - AMS to ams. > > Changes from V4: > - Rephrased the dt binding documents. > - Added dt-binding header for DTS file. > - Fix some of indention issue in dt documents. > > Reposting V5 as per Lee's. > > Documentation/devicetree/bindings/mfd/as3722.txt | 194 ++++++++++ > drivers/mfd/Kconfig | 12 + > drivers/mfd/Makefile | 1 + > drivers/mfd/as3722.c | 449 ++++++++++++++++++++++ > include/dt-bindings/mfd/as3722.h | 52 +++ > include/linux/mfd/as3722.h | 423 ++++++++++++++++++++ > 6 files changed, 1131 insertions(+), 0 deletions(-) > create mode 100644 Documentation/devicetree/bindings/mfd/as3722.txt > create mode 100644 drivers/mfd/as3722.c > create mode 100644 include/dt-bindings/mfd/as3722.h > create mode 100644 include/linux/mfd/as3722.h > > diff --git a/Documentation/devicetree/bindings/mfd/as3722.txt b/Documentation/devicetree/bindings/mfd/as3722.txt > new file mode 100644 > index 0000000..fc2191e > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/as3722.txt > @@ -0,0 +1,194 @@ > +* ams AS3722 Power management IC. > + > +Required properties: > +------------------- > +- compatible: Must be "ams,as3722". > +- reg: I2C device address. > +- interrupt-controller: AS3722 has internal interrupt controller which takes the > + interrupt request from internal sub-blocks like RTC, regulators, GPIOs as well > + as external input. > +- #interrupt-cells: Should be set to 2 for IRQ number and flags. > + The first cell is the IRQ number. IRQ numbers for different interrupt source > + of AS3722 are defined at dt-bindings/mfd/as3722.h > + The second cell is the flags, encoded as the trigger masks from binding document > + interrupts.txt, using dt-bindings/irq. > + > +Optional submodule and their properties: > +======================================= > + > +Pinmux and GPIO: > +=============== > +Device has 8 GPIO pins which can be configured as GPIO as well as the special IO > +functions. > + > +Please refer to pinctrl-bindings.txt in this directory for details of the > +common pinctrl bindings used by client devices, including the meaning of the > +phrase "pin configuration node". > + > +Following are properties which is needed if GPIO and pinmux functionality > +is required: > + Required properties: > + ------------------- > + - gpio-controller: Marks the device node as a GPIO controller. > + - #gpio-cells: Number of GPIO cells. Refer to binding document > + gpio/gpio.txt > + > + Optional properties: > + -------------------- > + Following properties are require if pin control setting is required > + at boot. > + - pinctrl-names: A pinctrl state named "default" be defined, using the > + bindings in pinctrl/pinctrl-binding.txt. > + - pinctrl[0...n]: Properties to contain the phandle that refer to > + different nodes of pin control settings. These nodes represents > + the pin control setting of state 0 to state n. Each of these > + nodes contains different subnodes to represents some desired > + configuration for a list of pins. This configuration can > + include the mux function to select on those pin(s), and > + various pin configuration parameters, such as pull-up, > + open drain. > + > + Each subnode have following properties: > + Required properties: > + - pins: List of pins. Valid values of pins properties are: > + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, > + gpio6, gpio7 > + > + Optional properties: > + function, bias-disable, bias-pull-up, bias-pull-down, > + bias-high-impedance, drive-open-drain. > + > + Valid values for function properties are: > + gpio, interrupt-out, gpio-in-interrupt, > + vsup-vbat-low-undebounce-out, > + vsup-vbat-low-debounce-out, > + voltage-in-standby, oc-pg-sd0, oc-pg-sd6, > + powergood-out, pwm-in, pwm-out, clk32k-out, > + watchdog-in, soft-reset-in > + > +Regulators: > +=========== > +Device has multiple DCDC and LDOs. The node "regulators" is require if regulator > +functionality is needed. > + > +Following are properties of regulator subnode. > + > + Optional properties: > + ------------------- > + The input supply of regulators are the optional properties on the > + regulator node. The input supply of these regulators are provided > + through following properties: > + vsup-sd2-supply: Input supply for SD2. > + vsup-sd3-supply: Input supply for SD3. > + vsup-sd4-supply: Input supply for SD4. > + vsup-sd5-supply: Input supply for SD5. > + vin-ldo0-supply: Input supply for LDO0. > + vin-ldo1-6-supply: Input supply for LDO1 and LDO6. > + vin-ldo2-5-7-supply: Input supply for LDO2, LDO5 and LDO7. > + vin-ldo3-4-supply: Input supply for LDO3 and LDO4. > + vin-ldo9-10-supply: Input supply for LDO9 and LDO10. > + vin-ldo11-supply: Input supply for LDO11. What is the data in these properties? The documentation isn't clear. In principle, the binding looks okay to me. g. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
