Thanks Alfredo. Is there any other possible way that will work for my situation? Anything would be helpful Johnu On 10/7/14, 2:25 PM, "Alfredo Deza" <adeza@xxxxxxxxxx> wrote: >On Tue, Oct 7, 2014 at 5:05 PM, Johnu George (johnugeo) ><johnugeo@xxxxxxxxx> wrote: >> Even when I try ceph-deploy install --dev <my ceph- branch in github>, I >> am seeing that it is getting installed from official ceph repo. How can >>I >> install ceph from my github repo or my local repo in all ceph nodes? (Or >> any other possibility? ). Someone can help me in setting this? > >That is just not possible. Only branches that are pushed to the Ceph >repo are available through the >`--dev` flag because they rely on a URL structure and repo that we >maintain. > > >> >> Johnu >> >> >> >> On 10/2/14, 1:55 PM, "Somnath Roy" <Somnath.Roy@xxxxxxxxxxx> wrote: >> >>>I think you should just skip 'ceph-deploy install' command and install >>>your version of the ceph package in all the nodes manually. >>>Otherwise there is ceph-deploy install --dev <git-branch> you can try >>>out. >>> >>>Thanks & Regards >>>Somnath >>> >>>-----Original Message----- >>>From: ceph-users [mailto:ceph-users-bounces@xxxxxxxxxxxxxx] On Behalf Of >>>Johnu George (johnugeo) >>>Sent: Thursday, October 02, 2014 1:08 PM >>>To: Loic Dachary >>>Cc: ceph-users@xxxxxxxxxxxxxx >>>Subject: Re: Multi node dev environment >>> >>>How do I use ceph-deploy in this case?. How do I get ceph-deploy to use >>>my privately built ceph package (with my changes) and install them in >>>all >>>ceph nodes? >>> >>> >>>Johnu >>> >>>On 10/2/14, 7:22 AM, "Loic Dachary" <loic@xxxxxxxxxxx> wrote: >>> >>>>Hi, >>>> >>>>I would use ceph-deploy >>>>http://ceph.com/docs/master/start/quick-start-preflight/#ceph-deploy-se >>>>tup but ... I've only done tests a few times and other people may have >>>>a more elaborate answer to this question ;-) >>>> >>>>Cheers >>>> >>>>On 02/10/2014 15:44, Johnu George (johnugeo) wrote:> Hi, >>>>> I was trying to set up a multi node dev environment. Till now, I was >>>>>building ceph by executing ./configure and make. I then used to test >>>>>the features by using vstart in a single node. Instead of it, if I >>>>>still need to use the multi node cluster for testing, what is the >>>>>proper way to do?. If I need to run benchmarks(using rados bench or >>>>>other benchmarking tools) after any code change, what is the right >>>>>practice to test some change in a multi node dev setup? ( Multi node >>>>>setup is needed as part of getting right performance results in >>>>>benchmark tests) >>>>> >>>>> >>>>> Thanks, >>>>> Johnu >>>>> >>>>> >>>>> _______________________________________________ >>>>> ceph-users mailing list >>>>> ceph-users@xxxxxxxxxxxxxx >>>>> http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com >>>>> >>>> >>>>-- >>>>Loïc Dachary, Artisan Logiciel Libre >>>> >>> >>>_______________________________________________ >>>ceph-users mailing list >>>ceph-users@xxxxxxxxxxxxxx >>>http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com >>> >>>________________________________ >>> >>>PLEASE NOTE: The information contained in this electronic mail message >>>is >>>intended only for the use of the designated recipient(s) named above. If >>>the reader of this message is not the intended recipient, you are hereby >>>notified that you have received this message in error and that any >>>review, dissemination, distribution, or copying of this message is >>>strictly prohibited. If you have received this communication in error, >>>please notify the sender by telephone or e-mail (as shown above) >>>immediately and destroy any and all copies of this message in your >>>possession (whether hard copies or electronically stored copies). >>> >> >> _______________________________________________ >> ceph-users mailing list >> ceph-users@xxxxxxxxxxxxxx >> http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com _______________________________________________ ceph-users mailing list ceph-users@xxxxxxxxxxxxxx http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
 |