On Tue, Oct 7, 2014 at 5:05 PM, Johnu George (johnugeo) <johnugeo@xxxxxxxxx> wrote: > Even when I try ceph-deploy install --dev <my ceph- branch in github>, I > am seeing that it is getting installed from official ceph repo. How can I > install ceph from my github repo or my local repo in all ceph nodes? (Or > any other possibility? ). Someone can help me in setting this? That is just not possible. Only branches that are pushed to the Ceph repo are available through the `--dev` flag because they rely on a URL structure and repo that we maintain. > > Johnu > > > > On 10/2/14, 1:55 PM, "Somnath Roy" <Somnath.Roy@xxxxxxxxxxx> wrote: > >>I think you should just skip 'ceph-deploy install' command and install >>your version of the ceph package in all the nodes manually. >>Otherwise there is ceph-deploy install --dev <git-branch> you can try out. >> >>Thanks & Regards >>Somnath >> >>-----Original Message----- >>From: ceph-users [mailto:ceph-users-bounces@xxxxxxxxxxxxxx] On Behalf Of >>Johnu George (johnugeo) >>Sent: Thursday, October 02, 2014 1:08 PM >>To: Loic Dachary >>Cc: ceph-users@xxxxxxxxxxxxxx >>Subject: Re: Multi node dev environment >> >>How do I use ceph-deploy in this case?. How do I get ceph-deploy to use >>my privately built ceph package (with my changes) and install them in all >>ceph nodes? >> >> >>Johnu >> >>On 10/2/14, 7:22 AM, "Loic Dachary" <loic@xxxxxxxxxxx> wrote: >> >>>Hi, >>> >>>I would use ceph-deploy >>>http://ceph.com/docs/master/start/quick-start-preflight/#ceph-deploy-se >>>tup but ... I've only done tests a few times and other people may have >>>a more elaborate answer to this question ;-) >>> >>>Cheers >>> >>>On 02/10/2014 15:44, Johnu George (johnugeo) wrote:> Hi, >>>> I was trying to set up a multi node dev environment. Till now, I was >>>>building ceph by executing ./configure and make. I then used to test >>>>the features by using vstart in a single node. Instead of it, if I >>>>still need to use the multi node cluster for testing, what is the >>>>proper way to do?. If I need to run benchmarks(using rados bench or >>>>other benchmarking tools) after any code change, what is the right >>>>practice to test some change in a multi node dev setup? ( Multi node >>>>setup is needed as part of getting right performance results in >>>>benchmark tests) >>>> >>>> >>>> Thanks, >>>> Johnu >>>> >>>> >>>> _______________________________________________ >>>> ceph-users mailing list >>>> ceph-users@xxxxxxxxxxxxxx >>>> http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com >>>> >>> >>>-- >>>Loïc Dachary, Artisan Logiciel Libre >>> >> >>_______________________________________________ >>ceph-users mailing list >>ceph-users@xxxxxxxxxxxxxx >>http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com >> >>________________________________ >> >>PLEASE NOTE: The information contained in this electronic mail message is >>intended only for the use of the designated recipient(s) named above. If >>the reader of this message is not the intended recipient, you are hereby >>notified that you have received this message in error and that any >>review, dissemination, distribution, or copying of this message is >>strictly prohibited. If you have received this communication in error, >>please notify the sender by telephone or e-mail (as shown above) >>immediately and destroy any and all copies of this message in your >>possession (whether hard copies or electronically stored copies). >> > > _______________________________________________ > ceph-users mailing list > ceph-users@xxxxxxxxxxxxxx > http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com _______________________________________________ ceph-users mailing list ceph-users@xxxxxxxxxxxxxx http://lists.ceph.com/listinfo.cgi/ceph-users-ceph.com
 |