I did that intentionally for posting. The format I am using is xxx-xxx-xxx Thanks, Dave George Teletone Inc. 561 674 3838 -----Original Message----- From: asterisk-ss7-bounces@xxxxxxxxxxxxxxxx [mailto:asterisk-ss7-bounces at lists.digium.com] On Behalf Of Paul Timmins Sent: Friday, February 05, 2010 2:49 PM To: asterisk-ss7 at lists.digium.com Subject: Re: SS7 2 T1s >>> 2 linksets same point code Also it looks like you're using ANSI signaling with pointcodes that are not like 000-000-000 format. Is that intentional? Dave George wrote: > Found a typo in cicbeginswith that solve the CIC numbering. > > We are now passing calls on both T1s. However the d channels on the second > t1 is not aligning. See our config below. The carrier is getting an alarm > on his d channel on the second T1. Carrier is using Nortel DMS. > > > Link state change: NOTALIGNED -> IDLE > Link state change: IDLE -> NOTALIGNED > > T4XXP (PCI) Card 0 Span 1 OK 0 0 0 ESF > B8ZS YEL 0 db (CSU)/0-133 feet (DSX-1) > T4XXP (PCI) Card 0 Span 2 OK 0 0 0 ESF > B8ZS YEL 0 db (CSU)/0-133 feet (DSX-1) > > Chan_dahdi.conf > cicbeginswith = 102 > sigchan = 1 > channel = 2-24 > sigchan = 25 > cicbeginswith = 126 > channel = 26-48 > > > > system.conf > > span=1,1,0,esf,b8zs > span=2,1,0,esf,b8zs > > > bchan=2-24 > mtp2=1 > > bchan=26-48 > mtp2=25 > > > > > > > > Thanks, > Dave George > Teletone Inc. > 561 674 3838 > > > -----Original Message----- > From: asterisk-ss7-bounces at lists.digium.com > [mailto:asterisk-ss7-bounces at lists.digium.com] On Behalf Of Dave George > Sent: Friday, February 05, 2010 12:31 PM > To: asterisk-ss7 at lists.digium.com > Subject: Re: [asterisk-ss7] SS7 2 T1s >>> 2 linksets same point code > > I decided to use 1 signaling link. My new problem is that the CIC on the > second T1 does not line up. It is starting at 125 instead of 126. > > This is what the carrier want. > T1 1: Slot 1 D channel CIC 102 to 124 > T2 2: Slot 25 D Channel CIC 126 to 148 > > cicbeginswith = 102 > channel = 2-24 > cicbeginwith = 126 > channel = 26-48 > sigchan = 1 > sigchan = 25 > > > asterisk is counting 125 as a CIC. See results from: ss7 unblock linkset 1 > > Sending remote unblock request on CIC 122 > Sending remote unblock request on CIC 123 > Sending remote unblock request on CIC 124 > Sending remote unblock request on CIC 125 > Sending remote unblock request on CIC 126 > Sending remote unblock request on CIC 127 > > > > Thanks, > Dave George > Teletone Inc. > 561 674 3838 > > > -----Original Message----- > From: asterisk-ss7-bounces at lists.digium.com > [mailto:asterisk-ss7-bounces at lists.digium.com] On Behalf Of Paul Timmins > Sent: Friday, February 05, 2010 11:17 AM > To: asterisk-ss7 at lists.digium.com > Subject: Re: [asterisk-ss7] SS7 2 T1s >>> 2 linksets same point code > > You'll want to set up the same linkset, and use slc=0 and slc=1, the SLC > has to match what the remote end is using. This is of course assuming > you're connected using F links since the adjpointcode and defaultdpc are > the same as each other. > > Dave George wrote: > >> Hi, >> >> I am using two T1 for SS7 on the same box. Both T1s are using the same >> > point codes. I have each T1 setup as its own linkset (Linkset 1 and linkset > 2). > >> The second linkset is not coming up. >> >> Is there any thing wrong with my config or setup? Can I have both T1s >> > usins the same point code. I did it this way so that if 1 T1 goes down the > second linkset and T1 stays up. > >> [trunkgroups] >> [channels] >> >> context=in_dahdi >> >> switchtype=national >> >> usecallerid=yes >> callwaiting=yes >> usecallingpres=yes >> callwaitingcallerid=yes >> threewaycalling=yes >> transfer=yes >> canpark=yes >> cancallforward=yes >> callreturn=yes >> echocancel=yes >> echocancelwhenbridged=yes >> signalling = ss7 >> ss7type = ansi >> >> >> >> >> >> group=1 >> callgroup=1 >> pickupgroup=1 >> ss7_called_nai=dynamic >> ss7_calling_nai=dynamic >> ss7_internationalprefix = 00 >> ss7_nationalprefix = 0 >> >> ; All settings apply to linkset 1 >> linkset = 1 >> context=in_dahdi >> pointcode = 157 >> adjpointcode = 163 >> defaultdpc = 163 >> networkindicator=national >> cicbeginswith = 102 >> channel = 2-24 >> sigchan = 1 >> >> >> group = 2 >> linkset = 2 >> context=in_dahdi >> pointcode = 157 >> adjpointcode = 163 >> defaultdpc = 163 >> networkindicator=national >> cicbeginswith = 126 >> channel = 26-48 >> sigchan = 25 >> >> >> >> >> Thanks, >> Dave George >> Teletone Inc. >> 561 674 3838 >> >> >> >> >> >> > > > -- _____________________________________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-ss7 mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-ss7
|