SS7 2 T1s >>> 2 linksets same point code

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Found a typo in cicbeginswith that solve the CIC numbering.  

We are now passing calls on both T1s.  However the d channels on the second
t1 is not aligning.  See our config below.  The carrier is getting an alarm
on his d channel on the second T1.  Carrier is using Nortel DMS.


Link state change: NOTALIGNED -> IDLE
Link state change: IDLE -> NOTALIGNED

T4XXP (PCI) Card 0 Span 1                OK      0      0      0      ESF
B8ZS YEL      0 db (CSU)/0-133 feet (DSX-1)
T4XXP (PCI) Card 0 Span 2                OK      0      0      0      ESF
B8ZS YEL      0 db (CSU)/0-133 feet (DSX-1)

Chan_dahdi.conf
cicbeginswith = 102
sigchan = 1
channel = 2-24
sigchan = 25
cicbeginswith = 126
channel = 26-48



system.conf

span=1,1,0,esf,b8zs
span=2,1,0,esf,b8zs


bchan=2-24
mtp2=1

bchan=26-48
mtp2=25







Thanks,
Dave George
Teletone Inc.
561 674 3838


-----Original Message-----
From: asterisk-ss7-bounces@xxxxxxxxxxxxxxxx
[mailto:asterisk-ss7-bounces at lists.digium.com] On Behalf Of Dave George
Sent: Friday, February 05, 2010 12:31 PM
To: asterisk-ss7 at lists.digium.com
Subject: Re: SS7 2 T1s >>> 2 linksets same point code

I decided to use 1 signaling link.  My new problem is that the CIC on the
second T1 does not line up.  It is starting at 125 instead of 126.

This is what the carrier want.
T1 1:  Slot 1 D channel CIC 102 to 124
T2 2: Slot 25 D Channel  CIC 126 to 148

cicbeginswith = 102
channel = 2-24
cicbeginwith = 126
channel = 26-48
sigchan = 1
sigchan = 25


asterisk is counting 125 as a CIC.  See results from: ss7 unblock linkset 1

Sending remote unblock request on CIC 122
Sending remote unblock request on CIC 123
Sending remote unblock request on CIC 124
Sending remote unblock request on CIC 125
Sending remote unblock request on CIC 126
Sending remote unblock request on CIC 127



Thanks,
Dave George
Teletone Inc.
561 674 3838


-----Original Message-----
From: asterisk-ss7-bounces@xxxxxxxxxxxxxxxx
[mailto:asterisk-ss7-bounces at lists.digium.com] On Behalf Of Paul Timmins
Sent: Friday, February 05, 2010 11:17 AM
To: asterisk-ss7 at lists.digium.com
Subject: Re: SS7 2 T1s >>> 2 linksets same point code

You'll want to set up the same linkset, and use slc=0 and slc=1, the SLC 
has to match what the remote end is using. This is of course assuming 
you're connected using F links since the adjpointcode and defaultdpc are 
the same as each other.

Dave George wrote:
> Hi,
>
> I am using two T1 for SS7 on the same box.  Both T1s are using the same
point codes.  I have each T1 setup as its own linkset (Linkset 1 and linkset
2).
>
> The second linkset is not coming up. 
>
> Is there any thing wrong with my config or setup?  Can I have both T1s
usins the same point code.  I did it this way so that if 1 T1 goes down the
second linkset and T1 stays up.
>
> [trunkgroups]
> [channels]
>  
>  context=in_dahdi
>   
>  switchtype=national
>  
>  usecallerid=yes
>  callwaiting=yes
>  usecallingpres=yes
>  callwaitingcallerid=yes
>  threewaycalling=yes
>  transfer=yes
>  canpark=yes
>   cancallforward=yes
>   callreturn=yes
>   echocancel=yes
>   echocancelwhenbridged=yes
>   signalling = ss7
>   ss7type = ansi
>  
>   
>  
>   
>  
>  group=1
>   callgroup=1
>   pickupgroup=1
>   ss7_called_nai=dynamic
>   ss7_calling_nai=dynamic
>   ss7_internationalprefix = 00
>   ss7_nationalprefix = 0
>   
>  ; All settings apply to linkset 1
>   linkset = 1
>   context=in_dahdi
>   pointcode = 157
>   adjpointcode = 163
>   defaultdpc = 163
>   networkindicator=national
>   cicbeginswith = 102
>   channel = 2-24
>   sigchan = 1
>  
>
>  group = 2
>  linkset = 2
>  context=in_dahdi
>  pointcode = 157
>  adjpointcode = 163
>  defaultdpc = 163
>  networkindicator=national
>  cicbeginswith = 126
>  channel = 26-48
>  sigchan = 25
>
>
>
>
> Thanks,
> Dave George
> Teletone Inc.
> 561 674 3838
>
>
>
>
>   


-- 
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --

asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-ss7


-- 
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --

asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-ss7




[Index of Archives]     [Asterisk App Development]     [PJ SIP]     [Gnu Gatekeeper]     [IETF Sipping]     [Info Cyrus]     [ALSA User]     [Fedora Linux Users]     [Linux SCTP]     [DCCP]     [Gimp]     [Yosemite Backpacking]     [Deep Creek Hot Springs]     [Yosemite Campsites]     [ISDN Cause Codes]     [Asterisk Books]

  Powered by Linux