I have similar issue with connecting to ZTE and HUAWEI switches. GRA comes not imediatelly, but after 1-2 minutes. Maybe you have the same issue. Did you wait long enough? On Saturday 19 July 2008 19:39, Low Yu Siang wrote: > Hi all, > > Thanks to the generous help from Mr. Pawel Ratajewski, I > have managed to solve the initial alignment problem(was > using the beta version 1.0.93 of chan_ss7 and it is > solved by downgrading to 1.0.0 following some reboots). > But I still couldn't get the ss7 link ready for making > calls. All CIC are in 'idle reset pending' status. The > below's is the log messages. > > [Jul 19 22:26:00] NOTICE[7676]: config.c:549 > load_config_link: Configured link 'l1' on linkset 'siuc', > firstcic=1 [Jul 19 22:26:00] DEBUG[7676]: config.c:674 > load_config_host: links 'l1:1' [Jul 19 22:26:00] > DEBUG[7676]: config.c:693 load_config_host: linkname > 'l1', no 1 [Jul 19 22:26:00] DEBUG[7676]: config.c:711 > load_config_host: host n_spans 1 [Jul 19 22:26:00] > WARNING[7676]: config.c:795 load_config_host: Missing > interface entries for host 'scvideo'. [Jul 19 22:26:00] > DEBUG[7676]: config.c:800 load_config_host: host scvideo, > n_spans 1 [Jul 19 22:26:00] NOTICE[7676]: config.c:959 > load_config: Configuring DPC 12864 for linkset 'siuc'. > [Jul 19 22:26:00] DEBUG[7676]: config.c:975 load_config: > Setting linkset 0 'siuc' enabled 1 [Jul 19 22:26:00] > DEBUG[7676]: config.c:173 show_config: Host scvideo, > links 1, ifs 0 [Jul 19 22:26:00] DEBUG[7676]: > l4isup.c:4302 isup_init: Links 1, host scvideo [Jul 19 > 22:26:00] DEBUG[7676]: l4isup.c:4310 isup_init: New CIC, > first_zapid 0, channelmask 0x7fff7fff, connector 1, > firstcic 1, schannel 16 [Jul 19 22:26:00] DEBUG[7676]: > transport.c:127 openchannel: Configuring CIC 1 on zaptel > device 1. [Jul 19 22:26:00] DEBUG[7676]: transport.c:127 > openchannel: Configuring CIC 2 on zaptel device 2. [Jul > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel: > Configuring CIC 3 on zaptel device 3. [Jul 19 22:26:00] > DEBUG[7676]: transport.c:127 openchannel: Configuring CIC > 4 on zaptel device 4. [Jul 19 22:26:00] DEBUG[7676]: > transport.c:127 openchannel: Configuring CIC 5 on zaptel > device 5. [Jul 19 22:26:00] DEBUG[7676]: transport.c:127 > openchannel: Configuring CIC 6 on zaptel device 6. [Jul > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel: > Configuring CIC 7 on zaptel device 7. [Jul 19 22:26:00] > DEBUG[7676]: transport.c:127 openchannel: Configuring CIC > 8 on zaptel device 8. [Jul 19 22:26:00] DEBUG[7676]: > transport.c:127 openchannel: Configuring CIC 9 on zaptel > device 9. [Jul 19 22:26:00] DEBUG[7676]: transport.c:127 > openchannel: Configuring CIC 10 on zaptel device 10. [Jul > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel: > Configuring CIC 11 on zaptel device 11. [Jul 19 22:26:00] > DEBUG[7676]: transport.c:127 openchannel: Configuring CIC > 12 on zaptel device 12. [Jul 19 22:26:00] DEBUG[7676]: > transport.c:127 openchannel: Configuring CIC 13 on zaptel > device 13. [Jul 19 22:26:00] DEBUG[7676]: transport.c:127 > openchannel: Configuring CIC 14 on zaptel device 14. [Jul > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel: > Configuring CIC 15 on zaptel device 15. [Jul 19 22:26:00] > DEBUG[7676]: transport.c:127 openchannel: Configuring CIC > 17 on zaptel device 17. [Jul 19 22:26:00] DEBUG[7676]: > transport.c:127 openchannel: Configuring CIC 18 on zaptel > device 18. [Jul 19 22:26:00] DEBUG[7676]: transport.c:127 > openchannel: Configuring CIC 19 on zaptel device 19. [Jul > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel: > Configuring CIC 20 on zaptel device 20. [Jul 19 22:26:00] > DEBUG[7676]: transport.c:127 openchannel: Configuring CIC > 21 on zaptel device 21. [Jul 19 22:26:00] DEBUG[7676]: > transport.c:127 openchannel: Configuring CIC 22 on zaptel > device 22. [Jul 19 22:26:00] DEBUG[7676]: transport.c:127 > openchannel: Configuring CIC 23 on zaptel device 23. [Jul > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel: > Configuring CIC 24 on zaptel device 24. [Jul 19 22:26:00] > DEBUG[7676]: transport.c:127 openchannel: Configuring CIC > 25 on zaptel device 25. [Jul 19 22:26:00] DEBUG[7676]: > transport.c:127 openchannel: Configuring CIC 26 on zaptel > device 26. [Jul 19 22:26:00] DEBUG[7676]: transport.c:127 > openchannel: Configuring CIC 27 on zaptel device 27. [Jul > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel: > Configuring CIC 28 on zaptel device 28. [Jul 19 22:26:00] > DEBUG[7676]: transport.c:127 openchannel: Configuring CIC > 29 on zaptel device 29. [Jul 19 22:26:00] DEBUG[7676]: > transport.c:127 openchannel: Configuring CIC 30 on zaptel > device 30. [Jul 19 22:26:00] DEBUG[7676]: transport.c:127 > openchannel: Configuring CIC 31 on zaptel device 31. [Jul > 19 22:26:00] DEBUG[7676]: cluster.c:780 > build_sender_list: Found no senders to supervise -- > Starting cluster thread, pid=7676. > [Jul 19 22:26:00] DEBUG[7676]: cluster.c:798 > wait_for_connections: wait 0 0 0 0 -- Starting continuity > check thread, pid=7676. == Registered channel type 'SS7' > (SS7 Protocol Driver) [Jul 19 22:26:00] NOTICE[7676]: > mtp.c:2190 mtp_init: Initialising 1 signalling links -- > Starting MTP thread, pid=7676. > -- SS7 channel loaded successfully. > Loaded chan_ss7 => (SS7 Protocol Support) > The 'load' command is deprecated and will be removed in a > future release. Please use 'module load' instead. *CLI> > -- Starting monitor thread, pid=7676. > [Jul 19 22:26:00] DEBUG[7711]: mtp.c:2085 mtp_init_link: > init link l1, linkset siuc, schannel 16. [Jul 19 > 22:26:00] DEBUG[7711]: mtp.c:681 start_initial_alignment: > Starting initial alignment on link 'l1', reason: Initial. > *CLI> [Jul 19 22:26:00] NOTICE[7711]: mtp.c:1792 > mtp_thread_main: Empty Zaptel output buffer detected, > outgoing packets may have been lost on link 'l1'. [Jul 19 > 22:26:00] DEBUG[7711]: mtp.c:988 mtp2_process_lssu: > Entering proving state for link 'l1'. [Jul 19 22:26:00] > DEBUG[7711]: mtp.c:499 t4_timeout: Proving successful on > link 'l1'. [Jul 19 22:26:00] NOTICE[7711]: mtp.c:1130 > mtp2_good_frame: Sending TRA to peer on link 'l1'.... > [Jul 19 22:26:00] DEBUG[7711]: mtp.c:1567 > mtp2_fill_zaptel_buf: Sending buffer to zaptel len=9, on > link 'l1' bsn=127, fsn=0. [Jul 19 22:26:00] DEBUG[7711]: > mtp.c:1567 mtp2_fill_zaptel_buf: Sending buffer to zaptel > len=25, on link 'l1' bsn=127, fsn=1. [Jul 19 22:26:00] > DEBUG[7711]: mtp.c:1250 mtp2_good_frame: Got MSU on link > 'l1' sio=1 slc=0 m.sls=0 bsn=1/1, fsn=1/0, sio=81, > len=15: 47 34 90 0c 11 80 f2 54 5c 10 aa ff 55 00 [Jul 19 > 22:26:00] DEBUG[7711]: mtp.c:1323 process_msu: Got SLTM, > sending SLTA 'l1', state=5. [Jul 19 22:26:00] > DEBUG[7711]: mtp.c:1567 mtp2_fill_zaptel_buf: Sending > buffer to zaptel len=18, on link 'l1' bsn=0, fsn=2. [Jul > 19 22:26:00] DEBUG[7711]: mtp.c:1250 mtp2_good_frame: Got > MSU on link 'l1' sio=1 slc=0 m.sls=0 bsn=1/1, fsn=1/1, > sio=81, len=22: 47 34 90 0c 21 f0 11 22 33 44 55 66 77 88 > 99 aa bb cc dd ee ff [Jul 19 22:26:00] DEBUG[7711]: > mtp.c:1338 process_msu: Got valid SLTA response on link > 'l1', state=5. [Jul 19 22:26:00] DEBUG[7711]: > l4isup.c:1344 send_init_grs: Sending GROUP RESET messages > on linkset 'siuc'. [Jul 19 22:26:00] DEBUG[7711]: > l4isup.c:389 mtp_enqueue_isup_packet: Queue packet CIC=1, > len=10, linkset='siuc', link='l1', slinkset='siuc', > slink='l1' [Jul 19 22:26:00] DEBUG[7711]: l4isup.c:1377 > send_init_grs: Group reset first 1, range 14 [Jul 19 > 22:26:00] DEBUG[7711]: l4isup.c:389 > mtp_enqueue_isup_packet: Queue packet CIC=17, len=10, > linkset='siuc', link='l1', slinkset='siuc', slink='l1' > [Jul 19 22:26:00] DEBUG[7711]: l4isup.c:1377 > send_init_grs: Group reset first 17, range 14 [Jul 19 > 22:26:00] WARNING[7711]: chan_ss7.c:617 process_event: > MTP is now UP on link 'l1'. [Jul 19 22:26:00] > DEBUG[7711]: mtp.c:1859 mtp_thread_main: Queue MSU, > lsi=0, last_send_ix=0, linkset=siuc, m->link=l1 [Jul 19 > 22:26:00] DEBUG[7711]: mtp.c:1859 mtp_thread_main: Queue > MSU, lsi=0, last_send_ix=0, linkset=siuc, m->link=l1 [Jul > 19 22:26:00] DEBUG[7711]: mtp.c:1567 > mtp2_fill_zaptel_buf: Sending buffer to zaptel len=14, on > link 'l1' bsn=1, fsn=3. [Jul 19 22:26:00] DEBUG[7711]: > mtp.c:1567 mtp2_fill_zaptel_buf: Sending buffer to zaptel > len=14, on link 'l1' bsn=1, fsn=4. [Jul 19 22:26:30] > NOTICE[7711]: l4isup.c:1220 t22_timeout: T22 timeout (No > "circuit group reset acknowledge" from peer) CIC=1. [Jul > 19 22:26:30] DEBUG[7711]: l4isup.c:389 > mtp_enqueue_isup_packet: Queue packet CIC=1, len=10, > linkset='siuc', link='l1', slinkset='siuc', slink='l1' > [Jul 19 22:26:30] NOTICE[7711]: l4isup.c:1220 > t22_timeout: T22 timeout (No "circuit group reset > acknowledge" from peer) CIC=17. [Jul 19 22:26:30] > DEBUG[7711]: l4isup.c:389 mtp_enqueue_isup_packet: Queue > packet CIC=17, len=10, linkset='siuc', link='l1', > slinkset='siuc', slink='l1' [Jul 19 22:26:30] > DEBUG[7711]: mtp.c:1859 mtp_thread_main: Queue MSU, > lsi=0, last_send_ix=0, linkset=siuc, m->link=l1 [Jul 19 > 22:26:30] DEBUG[7711]: mtp.c:1859 mtp_thread_main: Queue > MSU, lsi=0, last_send_ix=0, linkset=siuc, m->link=l1 [Jul > 19 22:26:30] DEBUG[7711]: mtp.c:1567 > mtp2_fill_zaptel_buf: Sending buffer to zaptel len=14, on > link 'l1' bsn=1, fsn=5. [Jul 19 22:26:30] DEBUG[7711]: > mtp.c:1567 mtp2_fill_zaptel_buf: Sending buffer to zaptel > len=14, on link 'l1' bsn=1, fsn=6. [Jul 19 22:27:00] > NOTICE[7711]: l4isup.c:1220 t22_timeout: T22 timeout (No > "circuit group reset acknowledge" from peer) CIC=1. [Jul > 19 22:27:00] DEBUG[7711]: l4isup.c:389 > mtp_enqueue_isup_packet: Queue packet CIC=1, len=10, > linkset='siuc', link='l1', slinkset='siuc', slink='l1' > [Jul 19 22:27:00] NOTICE[7711]: l4isup.c:1220 > t22_timeout: T22 timeout (No "circuit group reset > acknowledge" from peer) CIC=17. [Jul 19 22:27:00] > DEBUG[7711]: l4isup.c:389 mtp_enqueue_isup_packet: Queue > packet CIC=17, len=10, linkset='siuc', link='l1', > slinkset='siuc', slink='l1' > > Any help would be greatly appreciated. Thank you! > > Regards, > Low Yu Siang > > > > _________________________________________________________ >_ Not happy with your email address?. > Get the one you really want - millions of new email > addresses available now at Yahoo! > http://uk.docs.yahoo.com/ymail/new.html > > _______________________________________________ > --Bandwidth and Colocation Provided by > http://www.api-digital.com-- > > asterisk-ss7 mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-ss7
|