I am connecting to a Siemens switch. I waited for hours, T23 timer are also appearing. Currently I see in the chan_ss7 code that the timeout value is set at 30 seconds, are you suggesting that I should modify the code so that it is >120 seconds?
Thanks.
Yu Siang
--- On Mon, 21/7/08, Anton <anton.vazir at gmail.com> wrote:
> From: Anton <anton.vazir at gmail.com>
> Subject: Re: [asterisk-ss7] chan_ss7 - T22 timeout (No 'circuit group reset acknowledge' from peer)
> To: asterisk-ss7 at lists.digium.com, yusiang at yahoo.com
> Date: Monday, 21 July, 2008, 2:22 PM
> I have similar issue with connecting to ZTE and HUAWEI
> switches. GRA comes not imediatelly, but after 1-2 minutes.
>
> Maybe you have the same issue. Did you wait long enough?
>
> On Saturday 19 July 2008 19:39, Low Yu Siang wrote:
> > Hi all,
> >
> > Thanks to the generous help from Mr. Pawel Ratajewski,
> I
> > have managed to solve the initial alignment
> problem(was
> > using the beta version 1.0.93 of chan_ss7 and it is
> > solved by downgrading to 1.0.0 following some
> reboots).
> > But I still couldn't get the ss7 link ready for
> making
> > calls. All CIC are in 'idle reset pending'
> status. The
> > below's is the log messages.
> >
> > [Jul 19 22:26:00] NOTICE[7676]: config.c:549
> > load_config_link: Configured link 'l1' on
> linkset 'siuc',
> > firstcic=1 [Jul 19 22:26:00] DEBUG[7676]: config.c:674
> > load_config_host: links 'l1:1' [Jul 19
> 22:26:00]
> > DEBUG[7676]: config.c:693 load_config_host: linkname
> > 'l1', no 1 [Jul 19 22:26:00] DEBUG[7676]:
> config.c:711
> > load_config_host: host n_spans 1 [Jul 19 22:26:00]
> > WARNING[7676]: config.c:795 load_config_host: Missing
> > interface entries for host 'scvideo'. [Jul 19
> 22:26:00]
> > DEBUG[7676]: config.c:800 load_config_host: host
> scvideo,
> > n_spans 1 [Jul 19 22:26:00] NOTICE[7676]: config.c:959
> > load_config: Configuring DPC 12864 for linkset
> 'siuc'.
> > [Jul 19 22:26:00] DEBUG[7676]: config.c:975
> load_config:
> > Setting linkset 0 'siuc' enabled 1 [Jul 19
> 22:26:00]
> > DEBUG[7676]: config.c:173 show_config: Host scvideo,
> > links 1, ifs 0 [Jul 19 22:26:00] DEBUG[7676]:
> > l4isup.c:4302 isup_init: Links 1, host scvideo [Jul 19
> > 22:26:00] DEBUG[7676]: l4isup.c:4310 isup_init: New
> CIC,
> > first_zapid 0, channelmask 0x7fff7fff, connector 1,
> > firstcic 1, schannel 16 [Jul 19 22:26:00] DEBUG[7676]:
> > transport.c:127 openchannel: Configuring CIC 1 on
> zaptel
> > device 1. [Jul 19 22:26:00] DEBUG[7676]:
> transport.c:127
> > openchannel: Configuring CIC 2 on zaptel device 2.
> [Jul
> > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel:
> > Configuring CIC 3 on zaptel device 3. [Jul 19
> 22:26:00]
> > DEBUG[7676]: transport.c:127 openchannel: Configuring
> CIC
> > 4 on zaptel device 4. [Jul 19 22:26:00] DEBUG[7676]:
> > transport.c:127 openchannel: Configuring CIC 5 on
> zaptel
> > device 5. [Jul 19 22:26:00] DEBUG[7676]:
> transport.c:127
> > openchannel: Configuring CIC 6 on zaptel device 6.
> [Jul
> > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel:
> > Configuring CIC 7 on zaptel device 7. [Jul 19
> 22:26:00]
> > DEBUG[7676]: transport.c:127 openchannel: Configuring
> CIC
> > 8 on zaptel device 8. [Jul 19 22:26:00] DEBUG[7676]:
> > transport.c:127 openchannel: Configuring CIC 9 on
> zaptel
> > device 9. [Jul 19 22:26:00] DEBUG[7676]:
> transport.c:127
> > openchannel: Configuring CIC 10 on zaptel device 10.
> [Jul
> > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel:
> > Configuring CIC 11 on zaptel device 11. [Jul 19
> 22:26:00]
> > DEBUG[7676]: transport.c:127 openchannel: Configuring
> CIC
> > 12 on zaptel device 12. [Jul 19 22:26:00] DEBUG[7676]:
> > transport.c:127 openchannel: Configuring CIC 13 on
> zaptel
> > device 13. [Jul 19 22:26:00] DEBUG[7676]:
> transport.c:127
> > openchannel: Configuring CIC 14 on zaptel device 14.
> [Jul
> > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel:
> > Configuring CIC 15 on zaptel device 15. [Jul 19
> 22:26:00]
> > DEBUG[7676]: transport.c:127 openchannel: Configuring
> CIC
> > 17 on zaptel device 17. [Jul 19 22:26:00] DEBUG[7676]:
> > transport.c:127 openchannel: Configuring CIC 18 on
> zaptel
> > device 18. [Jul 19 22:26:00] DEBUG[7676]:
> transport.c:127
> > openchannel: Configuring CIC 19 on zaptel device 19.
> [Jul
> > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel:
> > Configuring CIC 20 on zaptel device 20. [Jul 19
> 22:26:00]
> > DEBUG[7676]: transport.c:127 openchannel: Configuring
> CIC
> > 21 on zaptel device 21. [Jul 19 22:26:00] DEBUG[7676]:
> > transport.c:127 openchannel: Configuring CIC 22 on
> zaptel
> > device 22. [Jul 19 22:26:00] DEBUG[7676]:
> transport.c:127
> > openchannel: Configuring CIC 23 on zaptel device 23.
> [Jul
> > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel:
> > Configuring CIC 24 on zaptel device 24. [Jul 19
> 22:26:00]
> > DEBUG[7676]: transport.c:127 openchannel: Configuring
> CIC
> > 25 on zaptel device 25. [Jul 19 22:26:00] DEBUG[7676]:
> > transport.c:127 openchannel: Configuring CIC 26 on
> zaptel
> > device 26. [Jul 19 22:26:00] DEBUG[7676]:
> transport.c:127
> > openchannel: Configuring CIC 27 on zaptel device 27.
> [Jul
> > 19 22:26:00] DEBUG[7676]: transport.c:127 openchannel:
> > Configuring CIC 28 on zaptel device 28. [Jul 19
> 22:26:00]
> > DEBUG[7676]: transport.c:127 openchannel: Configuring
> CIC
> > 29 on zaptel device 29. [Jul 19 22:26:00] DEBUG[7676]:
> > transport.c:127 openchannel: Configuring CIC 30 on
> zaptel
> > device 30. [Jul 19 22:26:00] DEBUG[7676]:
> transport.c:127
> > openchannel: Configuring CIC 31 on zaptel device 31.
> [Jul
> > 19 22:26:00] DEBUG[7676]: cluster.c:780
> > build_sender_list: Found no senders to supervise --
> > Starting cluster thread, pid=7676.
> > [Jul 19 22:26:00] DEBUG[7676]: cluster.c:798
> > wait_for_connections: wait 0 0 0 0 -- Starting
> continuity
> > check thread, pid=7676. == Registered channel type
> 'SS7'
> > (SS7 Protocol Driver) [Jul 19 22:26:00] NOTICE[7676]:
> > mtp.c:2190 mtp_init: Initialising 1 signalling links
> --
> > Starting MTP thread, pid=7676.
> > -- SS7 channel loaded successfully.
> > Loaded chan_ss7 => (SS7 Protocol Support)
> > The 'load' command is deprecated and will be
> removed in a
> > future release. Please use 'module load'
> instead. *CLI>
> > -- Starting monitor thread, pid=7676.
> > [Jul 19 22:26:00] DEBUG[7711]: mtp.c:2085
> mtp_init_link:
> > init link l1, linkset siuc, schannel 16. [Jul 19
> > 22:26:00] DEBUG[7711]: mtp.c:681
> start_initial_alignment:
> > Starting initial alignment on link 'l1',
> reason: Initial.
> > *CLI> [Jul 19 22:26:00] NOTICE[7711]: mtp.c:1792
> > mtp_thread_main: Empty Zaptel output buffer detected,
> > outgoing packets may have been lost on link
> 'l1'. [Jul 19
> > 22:26:00] DEBUG[7711]: mtp.c:988 mtp2_process_lssu:
> > Entering proving state for link 'l1'. [Jul 19
> 22:26:00]
> > DEBUG[7711]: mtp.c:499 t4_timeout: Proving successful
> on
> > link 'l1'. [Jul 19 22:26:00] NOTICE[7711]:
> mtp.c:1130
> > mtp2_good_frame: Sending TRA to peer on link
> 'l1'....
> > [Jul 19 22:26:00] DEBUG[7711]: mtp.c:1567
> > mtp2_fill_zaptel_buf: Sending buffer to zaptel len=9,
> on
> > link 'l1' bsn=127, fsn=0. [Jul 19 22:26:00]
> DEBUG[7711]:
> > mtp.c:1567 mtp2_fill_zaptel_buf: Sending buffer to
> zaptel
> > len=25, on link 'l1' bsn=127, fsn=1. [Jul 19
> 22:26:00]
> > DEBUG[7711]: mtp.c:1250 mtp2_good_frame: Got MSU on
> link
> > 'l1' sio=1 slc=0 m.sls=0 bsn=1/1, fsn=1/0,
> sio=81,
> > len=15: 47 34 90 0c 11 80 f2 54 5c 10 aa ff 55 00 [Jul
> 19
> > 22:26:00] DEBUG[7711]: mtp.c:1323 process_msu: Got
> SLTM,
> > sending SLTA 'l1', state=5. [Jul 19 22:26:00]
> > DEBUG[7711]: mtp.c:1567 mtp2_fill_zaptel_buf: Sending
> > buffer to zaptel len=18, on link 'l1' bsn=0,
> fsn=2. [Jul
> > 19 22:26:00] DEBUG[7711]: mtp.c:1250 mtp2_good_frame:
> Got
> > MSU on link 'l1' sio=1 slc=0 m.sls=0 bsn=1/1,
> fsn=1/1,
> > sio=81, len=22: 47 34 90 0c 21 f0 11 22 33 44 55 66 77
> 88
> > 99 aa bb cc dd ee ff [Jul 19 22:26:00] DEBUG[7711]:
> > mtp.c:1338 process_msu: Got valid SLTA response on
> link
> > 'l1', state=5. [Jul 19 22:26:00] DEBUG[7711]:
> > l4isup.c:1344 send_init_grs: Sending GROUP RESET
> messages
> > on linkset 'siuc'. [Jul 19 22:26:00]
> DEBUG[7711]:
> > l4isup.c:389 mtp_enqueue_isup_packet: Queue packet
> CIC=1,
> > len=10, linkset='siuc', link='l1',
> slinkset='siuc',
> > slink='l1' [Jul 19 22:26:00] DEBUG[7711]:
> l4isup.c:1377
> > send_init_grs: Group reset first 1, range 14 [Jul 19
> > 22:26:00] DEBUG[7711]: l4isup.c:389
> > mtp_enqueue_isup_packet: Queue packet CIC=17, len=10,
> > linkset='siuc', link='l1',
> slinkset='siuc', slink='l1'
> > [Jul 19 22:26:00] DEBUG[7711]: l4isup.c:1377
> > send_init_grs: Group reset first 17, range 14 [Jul 19
> > 22:26:00] WARNING[7711]: chan_ss7.c:617 process_event:
> > MTP is now UP on link 'l1'. [Jul 19 22:26:00]
> > DEBUG[7711]: mtp.c:1859 mtp_thread_main: Queue MSU,
> > lsi=0, last_send_ix=0, linkset=siuc, m->link=l1
> [Jul 19
> > 22:26:00] DEBUG[7711]: mtp.c:1859 mtp_thread_main:
> Queue
> > MSU, lsi=0, last_send_ix=0, linkset=siuc,
> m->link=l1 [Jul
> > 19 22:26:00] DEBUG[7711]: mtp.c:1567
> > mtp2_fill_zaptel_buf: Sending buffer to zaptel len=14,
> on
> > link 'l1' bsn=1, fsn=3. [Jul 19 22:26:00]
> DEBUG[7711]:
> > mtp.c:1567 mtp2_fill_zaptel_buf: Sending buffer to
> zaptel
> > len=14, on link 'l1' bsn=1, fsn=4. [Jul 19
> 22:26:30]
> > NOTICE[7711]: l4isup.c:1220 t22_timeout: T22 timeout
> (No
> > "circuit group reset acknowledge" from peer)
> CIC=1. [Jul
> > 19 22:26:30] DEBUG[7711]: l4isup.c:389
> > mtp_enqueue_isup_packet: Queue packet CIC=1, len=10,
> > linkset='siuc', link='l1',
> slinkset='siuc', slink='l1'
> > [Jul 19 22:26:30] NOTICE[7711]: l4isup.c:1220
> > t22_timeout: T22 timeout (No "circuit group reset
> > acknowledge" from peer) CIC=17. [Jul 19 22:26:30]
> > DEBUG[7711]: l4isup.c:389 mtp_enqueue_isup_packet:
> Queue
> > packet CIC=17, len=10, linkset='siuc',
> link='l1',
> > slinkset='siuc', slink='l1' [Jul 19
> 22:26:30]
> > DEBUG[7711]: mtp.c:1859 mtp_thread_main: Queue MSU,
> > lsi=0, last_send_ix=0, linkset=siuc, m->link=l1
> [Jul 19
> > 22:26:30] DEBUG[7711]: mtp.c:1859 mtp_thread_main:
> Queue
> > MSU, lsi=0, last_send_ix=0, linkset=siuc,
> m->link=l1 [Jul
> > 19 22:26:30] DEBUG[7711]: mtp.c:1567
> > mtp2_fill_zaptel_buf: Sending buffer to zaptel len=14,
> on
> > link 'l1' bsn=1, fsn=5. [Jul 19 22:26:30]
> DEBUG[7711]:
> > mtp.c:1567 mtp2_fill_zaptel_buf: Sending buffer to
> zaptel
> > len=14, on link 'l1' bsn=1, fsn=6. [Jul 19
> 22:27:00]
> > NOTICE[7711]: l4isup.c:1220 t22_timeout: T22 timeout
> (No
> > "circuit group reset acknowledge" from peer)
> CIC=1. [Jul
> > 19 22:27:00] DEBUG[7711]: l4isup.c:389
> > mtp_enqueue_isup_packet: Queue packet CIC=1, len=10,
> > linkset='siuc', link='l1',
> slinkset='siuc', slink='l1'
> > [Jul 19 22:27:00] NOTICE[7711]: l4isup.c:1220
> > t22_timeout: T22 timeout (No "circuit group reset
> > acknowledge" from peer) CIC=17. [Jul 19 22:27:00]
> > DEBUG[7711]: l4isup.c:389 mtp_enqueue_isup_packet:
> Queue
> > packet CIC=17, len=10, linkset='siuc',
> link='l1',
> > slinkset='siuc', slink='l1'
> >
> > Any help would be greatly appreciated. Thank you!
> >
> > Regards,
> > Low Yu Siang
> >
> >
> >
> >
> _________________________________________________________
> >_ Not happy with your email address?.
> > Get the one you really want - millions of new email
> > addresses available now at Yahoo!
> > http://uk.docs.yahoo.com/ymail/new.html
> >
> > _______________________________________________
> > --Bandwidth and Colocation Provided by
> > http://www.api-digital.com--
> >
> > asterisk-ss7 mailing list
> > To UNSUBSCRIBE or update options visit:
> >
> http://lists.digium.com/mailman/listinfo/asterisk-ss7
__________________________________________________________
Not happy with your email address?.
Get the one you really want - millions of new email addresses available now at Yahoo! http://uk.docs.yahoo.com/ymail/new.html
|