On April 17, 2021 8:57:22 AM EDT, angel Hall-Coulston <rammsteinium@xxxxxx.INVALID> wrote: >With due respect, please STOP abusing the mailing list and using it >like a 'chat room'. Please RTM as it’s all a bit lazy otherwise. > >> On 17 Apr 2021, at 01:57, H <agents@xxxxxxxxxxxxxx> wrote: >> >> On 04/16/2021 08:51 PM, H wrote: >>> On 04/16/2021 08:23 PM, Jonathon Koyle wrote: >>>>> The OP, ie me, just read up on virtual host configuration. I now >understand that it is not possible to have site1.conf and site2.conf as >in my first e-mail where I wanted to access the different sites using >1.2.3.4/site1 and 1.2.3.4/site2 etc. >>>>> >>>>> My reading suggests that instead accessing them as site1.1.2.3.4 >and site2.1.2.3.4 should work with the following minimal conf >>>> ServerName should either be a hostname or an IP Address. Httpd is >>>> going to compare this value to the HOST header in an HTTP request >and >>>> it should match what you are putting in host section of the URL >For >>>> example, if you owned example.com the ServerName directives would >>>> site1.example.com and site2.example.com. >>>> >>>> If you are just testing and don't have a domain or DNS, you could >just >>>> set SeverName to site1 and site2 and add entries in your host file >>>> that map to the IP address >>>> >>>> 1.2.3.4 site1 >>>> 1.2.3.4 site2 >>>> >>>> >--------------------------------------------------------------------- >>>> To unsubscribe, e-mail: users-unsubscribe@xxxxxxxxxxxxxxxx >>>> For additional commands, e-mail: users-help@xxxxxxxxxxxxxxxx >>>> >>> I am using one external IP -address for now so you are saying the >ServerName should be site1.a.b.c.d and site2.a.b.c.d, respectively, >where a.b.c.d is the same? >>> >>> >>> >--------------------------------------------------------------------- >>> To unsubscribe, e-mail: users-unsubscribe@xxxxxxxxxxxxxxxx >>> For additional commands, e-mail: users-help@xxxxxxxxxxxxxxxx >>> >> The four sites I have are loading fine - and have through most of >this testing BUT, the logging always goes to the access and error log >defined in the conf file first in the /etc/httpd/conf.d directory. I >understand this is because they are loaded in alphabetical order and >defaults to the first one mentioned unless a later match is found. >> >> Could there be some /very/ basic configuration I have missed to >enable/disable and that's why this occurring? >> >> I should also mention that once I have all sites loading and logging >done correctly, the next step is to load php-fpm to be able to use >different php versions for some of the sites. However, until I have the >logging working as intended I am not working on that... >> >> >> --------------------------------------------------------------------- >> To unsubscribe, e-mail: users-unsubscribe@xxxxxxxxxxxxxxxx >> For additional commands, e-mail: users-help@xxxxxxxxxxxxxxxx >> > > >--------------------------------------------------------------------- >To unsubscribe, e-mail: users-unsubscribe@xxxxxxxxxxxxxxxx >For additional commands, e-mail: users-help@xxxxxxxxxxxxxxxx Well, if my problem is so easily solved, perhaps you can tell me what I am doing wrong? That would solve two issues, I no longer have to post questions on this topic and you could show that you are helpful and knowledgable... Obviously I have consulted other sources, including the documentation. This is a user support list, is it not? And, you can always ignore posts... Perhaps i misremember, but was not your previous post a suggestion to switch to MAMP?? --------------------------------------------------------------------- To unsubscribe, e-mail: users-unsubscribe@xxxxxxxxxxxxxxxx For additional commands, e-mail: users-help@xxxxxxxxxxxxxxxx
![]() |