On Wednesday, 23 August 2023 at 09:25, Peter Robinson wrote: > Hi Dominik, > > > > The 2023.10 RC series are now landing in F-39 and rawhide. There's > > > been the beginnings of a few enhancements. > > > > > > The first one that is noticeable is a bootmenu during the firmware > > > init process where it will allow you to select the > > > device/partition you wish to boot from, with the default selected > > > and the usual time out. It should make things a little easier for > > > things like reinstalling off a USB stick for devices that support > > > that sort of install. > > > > > > I've done some testing across a bunch of devices, various RPi, the > > > Pinebook pro and numerous SBCs so I think it should work just > > > fine, at least be no different than the usual process but I'd like > > > to hear any feedback. > > > > I copied the Pinebook Pro u-boot binaries from > > uboot-images-armv8-2023.10-0.4.rc3.fc39.noarch.rpm > > (https://koji.fedoraproject.org/koji/buildinfo?buildID=2277261) from > > /usr/share/uboot/pinebook-pro-rk3399/ to a μSD card (previously > > formatted using spi-flashing disk script). Then I did the steps from > > https://nullr0ute.com/2021/05/fedora-on-the-pinebook-pro/ "Write the > > firmware to flash" section. > > > > Unfortunately, after reset (or power-off/power-on cycle), I get this: > > ... > > U-Boot SPL 2023.10-rc3 (Aug 21 2023 - 00:00:00 +0000) > > Trying to boot from SPI > > Trying to boot from MMC1 > > mmc_load_image_raw_sector: mmc block read error > > Trying to boot from SPI > > Trying to boot from MMC2 > > Card did not respond to voltage select! : -110 > > spl: mmc init failed with error: -95 > > SPL: failed to boot from all boot devices > > ### ERROR ### Please RESET the board ### > > > > I checked the spi-flashing-disk script, and all it does is create a > > vfat formatted partition and copy the 4 binaries from the directory > > corresponding to the board model. I think I did everything > > correctly, so is the new u-boot broken on PBP? > > I've confirmed a similar problem, I was testing some of this on the > PBP against RC2 as I was developing it but never tested the RC3. I wish I had known that before trying the latest build. :( > Any chance you can grab one of the RC2 builds from koji [1] and see if > you have better luck? Also maybe 2023.07 from koji too. I'll try and > get to the bottom of this in the next week or so. Unfortunately, it'll take some time, because the SPL is unable to load the next stage from SD and I have to enter the maskrom mode[1] to zero the SPI. Would you happen to have instructions on how to build an image that can be flashed in that mode using rkdeveloptool wl 0 newspi.bin ? That'd make things easier. I don't have time to open my PBP right now and probably won't have it for a couple of weeks. [1] https://wiki.pine64.org/wiki/Pinebook_Pro_SPI Regards, Dominik -- Fedora https://fedoraproject.org There should be a science of discontent. People need hard times and oppression to develop psychic muscles. -- from "Collected Sayings of Muad'Dib" by the Princess Irulan _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx Fedora Code of Conduct: https://docs.fedoraproject.org/en-US/project/code-of-conduct/ List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx Do not reply to spam, report it: https://pagure.io/fedora-infrastructure/new_issue
