----- Original Message ----- > > > On 3/7/19 5:48 PM, Paul Whalen wrote: > > Hi Robert, > > > > ----- Original Message ----- > >> I just tested with Fedora-Minimal-armhfp-30-20190307.n.0-sda > >> > >> On a Cubieboard2: > >> > >> I installed the image on a 4GB uSD card and deleted all partitions. > >> I installed the image on a 240GB SSD drive and enlarged the rootfs > >> partition to about 6GB. > >> > >> I installed the cards on a Cubieboard2, attached the console and > >> booted. The boot failed. This process has been working for years, so > >> something serious has been broken in the uboot. > > Thanks for testing and reporting the issue. It seems to affect the > > allwinner > > boards (Cubietruck, Banana Pi etc). > > I figured it would effect all Allwinner boards. > > > Not fixed in uboot-tools-2019.04-0.4.rc3.fc30. You can use the F29 > > builds to continue testing until we can get a fix in F30. > > Have you tested with something after 2018-09 rc3? I am assuming that > the current F29 is later than this... Yes, uboot-tools-2018.09-2.fc29 is the latest in F29 and working on the Cubietruck and Banana Pi. Paul > > > > > >> U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) > >> DRAM: 1024 MiB > >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > >> Trying to boot from MMC1 > >> > >> > >> U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology > >> > >> CPU: Allwinner A20 (SUN7I) > >> Model: Cubietech Cubieboard2 > >> I2C: ready > >> DRAM: 1 GiB > >> MMC: mmc@1c0f000: 0 > >> Loading Environment from FAT... ** No valid partitions found ** > >> In: serial > >> Out: serial > >> Err: serial > >> SCSI: Target spinup took 0 ms. > >> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > >> flags: ncq stag pm led clo only pmp pio slum part ccc apst > >> > >> Net: sunxi_set_gate: (CLK#66) unhandled > >> eth0: ethernet@1c50000 > >> starting USB... > >> USB0: USB EHCI 1.00 > >> USB1: USB OHCI 1.0 > >> USB2: USB EHCI 1.00 > >> USB3: USB OHCI 1.0 > >> scanning bus 0 for devices... 1 USB Device(s) found > >> scanning bus 1 for devices... 1 USB Device(s) found > >> scanning bus 2 for devices... 1 USB Device(s) found > >> scanning bus 3 for devices... 1 USB Device(s) found > >> scanning usb for storage devices... 0 Storage Device(s) found > >> Hit any key to stop autoboot: 0 > >> switch to partitions #0, OK > >> mmc0 is current device > >> ** Invalid partition 1 ** > >> scanning bus for devices... > >> data abort > >> pc : [<7ef86b0e>] lr : [<7ef82d89>] > >> reloc pc : [<4a01ab0e>] lr : [<4a016d89>] > >> sp : 7af43ad0 ip : 0000001c fp : 000000c0 > >> r10: 00000000 r9 : 7af4bed8 r8 : 00000000 > >> r7 : 7af43d50 r6 : 7efc4894 r5 : 7efcc2f8 r4 : 7efcc2f8 > >> r3 : 00000000 r2 : 00000000 r1 : ea000016 r0 : 7efcc2f8 > >> Flags: nZcv IRQs off FIQs off Mode SVC_32 > >> Code: e92dbd10 f8d045f0 b0858080 1000f8d8 (f8d14604) > >> Resetting CPU ... > >> > >> resetting ... > >> > >> U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) > >> DRAM: 1024 MiB > >> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > >> Trying to boot from MMC1 > >> > >> > >> U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology > >> > >> CPU: Allwinner A20 (SUN7I) > >> Model: Cubietech Cubieboard2 > >> I2C: ready > >> DRAM: 1 GiB > >> MMC: mmc@1c0f000: 0 > >> Loading Environment from FAT... ** No valid partitions found ** > >> In: serial > >> Out: serial > >> Err: serial > >> > >> and so forth. > >> > >> On 3/3/19 5:45 PM, Peter Robinson wrote: > >>> On Sun, Mar 3, 2019 at 10:18 PM Robert Moskowitz <rgm@xxxxxxxxxxxxxxx> > >>> wrote: > >>>> The environment is only the uboot on the uSD and all partitions on the > >>>> sata HD. > >>>> > >>>> I have been doing this for years now with no problem. uboot has always > >>>> switched to looking for the sata hd for partitions if no partitions on > >>>> the uSD: > >>>> > >>>> U-Boot SPL 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000) > >>>> DRAM: 1024 MiB > >>>> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > >>>> Trying to boot from MMC1 > >>>> > >>>> > >>>> U-Boot 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000) Allwinner Technology > >>>> > >>>> CPU: Allwinner A20 (SUN7I) > >>>> Model: Cubietech Cubieboard2 > >>>> I2C: ready > >>>> DRAM: 1 GiB > >>>> MMC: SUNXI SD/MMC: 0 > >>>> Loading Environment from FAT... ** No valid partitions found ** > >>>> In: serial > >>>> Out: serial > >>>> Err: serial > >>>> SCSI: Target spinup took 0 ms. > >>>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > >>>> flags: ncq stag pm led clo only pmp pio slum part ccc apst > >>>> > >>>> Net: eth0: ethernet@01c50000 > >>>> starting USB... > >>>> USB0: USB EHCI 1.00 > >>>> USB1: USB OHCI 1.0 > >>>> USB2: USB EHCI 1.00 > >>>> USB3: USB OHCI 1.0 > >>>> scanning bus 0 for devices... 1 USB Device(s) found > >>>> scanning bus 2 for devices... 1 USB Device(s) found > >>>> scanning usb for storage devices... 0 Storage Device(s) found > >>>> Hit any key to stop autoboot: 0 > >>>> switch to partitions #0, OK > >>>> mmc0 is current device > >>>> ** Invalid partition 1 ** > >>>> scanning bus for devices... > >>>> Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0 > >>>> Type: Hard Disk > >>>> Capacity: 76319.0 MB = 74.5 GB (156301488 x 512) > >>>> Found 1 device(s). > >>>> > >>>> Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0 > >>>> Type: Hard Disk > >>>> Capacity: 76319.0 MB = 74.5 GB (156301488 x 512) > >>>> ... is now current device > >>>> Scanning scsi 0:2... > >>>> Found /extlinux/extlinux.conf > >>>> Retrieving file: /extlinux/extlinux.conf > >>>> 567 bytes read in 33 ms (16.6 KiB/s) > >>>> Ignoring unknown command: ui > >>>> Ignoring malformed menu command: autoboot > >>>> Ignoring malformed menu command: hidden > >>>> Ignoring unknown command: totaltimeout > >>>> CentOS-Userland-7-armv7hl-generic-Minimal-1810 Boot Options. > >>>> 1: CentOS-Userland-7-armv7hl-generic-Minimal-1810 > >>>> (4.14.82-201.el7.armv7hl) > >>>> > >>>> Enter choice: 1: CentOS-Userland-7-armv7hl-generic-Minimal-1810 > >>>> (4.14.82- > >>>> 201.el7.armv7hl) > >>>> Retrieving file: /initramfs-4.14.82-201.el7.armv7hl.img > >>>> > >>>> Yes, this particular event is with the current Centos arm image, but > >>>> that should not matter. I have to get this Centos image built and > >>>> installed before I can test with Fedora arm image.... > >>>> > >>>> I grabbed a more recent uboot via: > >>>> > >>>> Fedora-Minimal-armhfp-30-20190301.n.0-sda > >>>> > >>>> When I try booting with the uboot in that image I get: > >>>> > >>>> U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) > >>>> DRAM: 1024 MiB > >>>> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > >>>> Trying to boot from MMC1 > >>>> > >>>> > >>>> U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology > >>>> > >>>> CPU: Allwinner A20 (SUN7I) > >>>> Model: Cubietech Cubieboard2 > >>>> I2C: ready > >>>> DRAM: 1 GiB > >>>> MMC: mmc@1c0f000: 0 > >>>> Loading Environment from FAT... ** No valid partitions found ** > >>>> In: serial > >>>> Out: serial > >>>> Err: serial > >>>> SCSI: Target spinup took 0 ms. > >>>> AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > >>>> flags: ncq stag pm led clo only pmp pio slum part ccc apst > >>>> > >>>> Net: sunxi_set_gate: (CLK#66) unhandled > >>>> eth0: ethernet@1c50000 > >>>> starting USB... > >>>> USB0: USB EHCI 1.00 > >>>> USB1: USB OHCI 1.0 > >>>> USB2: USB EHCI 1.00 > >>>> USB3: USB OHCI 1.0 > >>>> scanning bus 0 for devices... 1 USB Device(s) found > >>>> scanning bus 1 for devices... 1 USB Device(s) found > >>>> scanning bus 2 for devices... 1 USB Device(s) found > >>>> scanning bus 3 for devices... 1 USB Device(s) found > >>>> scanning usb for storage devices... 0 Storage Device(s) found > >>>> Hit any key to stop autoboot: 0 > >>>> switch to partitions #0, OK > >>>> mmc0 is current device > >>>> ** Invalid partition 1 ** > >>>> scanning bus for devices... > >>>> data abort > >>>> pc : [<7ef86b0e>] lr : [<7ef82d89>] > >>>> reloc pc : [<4a01ab0e>] lr : [<4a016d89>] > >>>> sp : 7af43ad0 ip : 0000001c fp : 000000c0 > >>>> r10: 00000000 r9 : 7af4bed8 r8 : 00000000 > >>>> r7 : 7af43d50 r6 : 7efc4894 r5 : 7efcc2f8 r4 : 7efcc2f8 > >>>> r3 : 00000000 r2 : 00000000 r1 : ea000016 r0 : 7efcc2f8 > >>>> Flags: nZcv IRQs off FIQs off Mode SVC_32 > >>>> Code: e92dbd10 f8d045f0 b0858080 1000f8d8 (f8d14604) > >>>> Resetting CPU ... > >>>> > >>>> resetting ... > >>>> > >>>> U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) > >>>> DRAM: 1024 MiB > >>>> CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > >>>> Trying to boot from MMC1 > >>>> > >>>> > >>>> U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology > >>>> > >>>> CPU: Allwinner A20 (SUN7I) > >>>> Model: Cubietech Cubieboard2 > >>>> I2C: ready > >>>> DRAM: 1 GiB > >>>> MMC: mmc@1c0f000: 0 > >>>> Loading Environment from FAT... ** No valid partitions found ** > >>>> In: serial > >>>> Out: serial > >>>> Err: serial > >>>> > >>>> and so forth.... > >>>> > >>>> If there is a rc3 available, please tell me what image to grab for it > >>>> and I can test with that. > >>> There should be a rc3 this week. > >>> > >> _______________________________________________ > >> arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx > >> To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx > >> Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html > >> List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines > >> List Archives: > >> https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx > >> > > _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
