On 3/7/19 5:48 PM, Paul Whalen wrote:
Hi Robert,
----- Original Message -----
I just tested with Fedora-Minimal-armhfp-30-20190307.n.0-sda
On a Cubieboard2:
I installed the image on a 4GB uSD card and deleted all partitions.
I installed the image on a 240GB SSD drive and enlarged the rootfs
partition to about 6GB.
I installed the cards on a Cubieboard2, attached the console and
booted. The boot failed. This process has been working for years, so
something serious has been broken in the uboot.
Thanks for testing and reporting the issue. It seems to affect the allwinner
boards (Cubietruck, Banana Pi etc).
I figured it would effect all Allwinner boards.
Not fixed in uboot-tools-2019.04-0.4.rc3.fc30. You can use the F29
builds to continue testing until we can get a fix in F30.
Have you tested with something after 2018-09 rc3? I am assuming that
the current F29 is later than this...
Paul
U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Cubietech Cubieboard2
I2C: ready
DRAM: 1 GiB
MMC: mmc@1c0f000: 0
Loading Environment from FAT... ** No valid partitions found **
In: serial
Out: serial
Err: serial
SCSI: Target spinup took 0 ms.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net: sunxi_set_gate: (CLK#66) unhandled
eth0: ethernet@1c50000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning bus 3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
** Invalid partition 1 **
scanning bus for devices...
data abort
pc : [<7ef86b0e>] lr : [<7ef82d89>]
reloc pc : [<4a01ab0e>] lr : [<4a016d89>]
sp : 7af43ad0 ip : 0000001c fp : 000000c0
r10: 00000000 r9 : 7af4bed8 r8 : 00000000
r7 : 7af43d50 r6 : 7efc4894 r5 : 7efcc2f8 r4 : 7efcc2f8
r3 : 00000000 r2 : 00000000 r1 : ea000016 r0 : 7efcc2f8
Flags: nZcv IRQs off FIQs off Mode SVC_32
Code: e92dbd10 f8d045f0 b0858080 1000f8d8 (f8d14604)
Resetting CPU ...
resetting ...
U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Cubietech Cubieboard2
I2C: ready
DRAM: 1 GiB
MMC: mmc@1c0f000: 0
Loading Environment from FAT... ** No valid partitions found **
In: serial
Out: serial
Err: serial
and so forth.
On 3/3/19 5:45 PM, Peter Robinson wrote:
On Sun, Mar 3, 2019 at 10:18 PM Robert Moskowitz <rgm@xxxxxxxxxxxxxxx>
wrote:
The environment is only the uboot on the uSD and all partitions on the
sata HD.
I have been doing this for years now with no problem. uboot has always
switched to looking for the sata hd for partitions if no partitions on
the uSD:
U-Boot SPL 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Cubietech Cubieboard2
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
Loading Environment from FAT... ** No valid partitions found **
In: serial
Out: serial
Err: serial
SCSI: Target spinup took 0 ms.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net: eth0: ethernet@01c50000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
** Invalid partition 1 **
scanning bus for devices...
Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0
Type: Hard Disk
Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)
Found 1 device(s).
Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0
Type: Hard Disk
Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)
... is now current device
Scanning scsi 0:2...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
567 bytes read in 33 ms (16.6 KiB/s)
Ignoring unknown command: ui
Ignoring malformed menu command: autoboot
Ignoring malformed menu command: hidden
Ignoring unknown command: totaltimeout
CentOS-Userland-7-armv7hl-generic-Minimal-1810 Boot Options.
1: CentOS-Userland-7-armv7hl-generic-Minimal-1810
(4.14.82-201.el7.armv7hl)
Enter choice: 1: CentOS-Userland-7-armv7hl-generic-Minimal-1810
(4.14.82-
201.el7.armv7hl)
Retrieving file: /initramfs-4.14.82-201.el7.armv7hl.img
Yes, this particular event is with the current Centos arm image, but
that should not matter. I have to get this Centos image built and
installed before I can test with Fedora arm image....
I grabbed a more recent uboot via:
Fedora-Minimal-armhfp-30-20190301.n.0-sda
When I try booting with the uboot in that image I get:
U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Cubietech Cubieboard2
I2C: ready
DRAM: 1 GiB
MMC: mmc@1c0f000: 0
Loading Environment from FAT... ** No valid partitions found **
In: serial
Out: serial
Err: serial
SCSI: Target spinup took 0 ms.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net: sunxi_set_gate: (CLK#66) unhandled
eth0: ethernet@1c50000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning bus 3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
** Invalid partition 1 **
scanning bus for devices...
data abort
pc : [<7ef86b0e>] lr : [<7ef82d89>]
reloc pc : [<4a01ab0e>] lr : [<4a016d89>]
sp : 7af43ad0 ip : 0000001c fp : 000000c0
r10: 00000000 r9 : 7af4bed8 r8 : 00000000
r7 : 7af43d50 r6 : 7efc4894 r5 : 7efcc2f8 r4 : 7efcc2f8
r3 : 00000000 r2 : 00000000 r1 : ea000016 r0 : 7efcc2f8
Flags: nZcv IRQs off FIQs off Mode SVC_32
Code: e92dbd10 f8d045f0 b0858080 1000f8d8 (f8d14604)
Resetting CPU ...
resetting ...
U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Cubietech Cubieboard2
I2C: ready
DRAM: 1 GiB
MMC: mmc@1c0f000: 0
Loading Environment from FAT... ** No valid partitions found **
In: serial
Out: serial
Err: serial
and so forth....
If there is a rc3 available, please tell me what image to grab for it
and I can test with that.
There should be a rc3 this week.
_______________________________________________
arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html
List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines
List Archives:
https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
_______________________________________________
arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html
List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines
List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
