The environment is only the uboot on the uSD and all partitions on the
sata HD.
I have been doing this for years now with no problem. uboot has always
switched to looking for the sata hd for partitions if no partitions on
the uSD:
U-Boot SPL 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Cubietech Cubieboard2
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
Loading Environment from FAT... ** No valid partitions found **
In: serial
Out: serial
Err: serial
SCSI: Target spinup took 0 ms.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net: eth0: ethernet@01c50000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
** Invalid partition 1 **
scanning bus for devices...
Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0
Type: Hard Disk
Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)
Found 1 device(s).
Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0
Type: Hard Disk
Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)
... is now current device
Scanning scsi 0:2...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
567 bytes read in 33 ms (16.6 KiB/s)
Ignoring unknown command: ui
Ignoring malformed menu command: autoboot
Ignoring malformed menu command: hidden
Ignoring unknown command: totaltimeout
CentOS-Userland-7-armv7hl-generic-Minimal-1810 Boot Options.
1: CentOS-Userland-7-armv7hl-generic-Minimal-1810
(4.14.82-201.el7.armv7hl)
Enter choice: 1: CentOS-Userland-7-armv7hl-generic-Minimal-1810 (4.14.82-
201.el7.armv7hl)
Retrieving file: /initramfs-4.14.82-201.el7.armv7hl.img
Yes, this particular event is with the current Centos arm image, but
that should not matter. I have to get this Centos image built and
installed before I can test with Fedora arm image....
I grabbed a more recent uboot via:
Fedora-Minimal-armhfp-30-20190301.n.0-sda
When I try booting with the uboot in that image I get:
U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Cubietech Cubieboard2
I2C: ready
DRAM: 1 GiB
MMC: mmc@1c0f000: 0
Loading Environment from FAT... ** No valid partitions found **
In: serial
Out: serial
Err: serial
SCSI: Target spinup took 0 ms.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net: sunxi_set_gate: (CLK#66) unhandled
eth0: ethernet@1c50000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
USB2: USB EHCI 1.00
USB3: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning bus 3 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
** Invalid partition 1 **
scanning bus for devices...
data abort
pc : [<7ef86b0e>] lr : [<7ef82d89>]
reloc pc : [<4a01ab0e>] lr : [<4a016d89>]
sp : 7af43ad0 ip : 0000001c fp : 000000c0
r10: 00000000 r9 : 7af4bed8 r8 : 00000000
r7 : 7af43d50 r6 : 7efc4894 r5 : 7efcc2f8 r4 : 7efcc2f8
r3 : 00000000 r2 : 00000000 r1 : ea000016 r0 : 7efcc2f8
Flags: nZcv IRQs off FIQs off Mode SVC_32
Code: e92dbd10 f8d045f0 b0858080 1000f8d8 (f8d14604)
Resetting CPU ...
resetting ...
U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from MMC1
U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Cubietech Cubieboard2
I2C: ready
DRAM: 1 GiB
MMC: mmc@1c0f000: 0
Loading Environment from FAT... ** No valid partitions found **
In: serial
Out: serial
Err: serial
and so forth....
If there is a rc3 available, please tell me what image to grab for it
and I can test with that.
Meanwhile, it seems there is a problem here.
thanks
_______________________________________________
arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html
List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines
List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
