For reference this issue is now fixed in the 2019.04 GA build on it's way to F-30 testing repos. Peter On Sun, Mar 3, 2019 at 10:18 PM Robert Moskowitz <rgm@xxxxxxxxxxxxxxx> wrote: > > The environment is only the uboot on the uSD and all partitions on the > sata HD. > > I have been doing this for years now with no problem. uboot has always > switched to looking for the sata hd for partitions if no partitions on > the uSD: > > U-Boot SPL 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000) > DRAM: 1024 MiB > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > Trying to boot from MMC1 > > > U-Boot 2018.09-rc3 (Sep 05 2018 - 19:12:48 +0000) Allwinner Technology > > CPU: Allwinner A20 (SUN7I) > Model: Cubietech Cubieboard2 > I2C: ready > DRAM: 1 GiB > MMC: SUNXI SD/MMC: 0 > Loading Environment from FAT... ** No valid partitions found ** > In: serial > Out: serial > Err: serial > SCSI: Target spinup took 0 ms. > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > flags: ncq stag pm led clo only pmp pio slum part ccc apst > > Net: eth0: ethernet@01c50000 > starting USB... > USB0: USB EHCI 1.00 > USB1: USB OHCI 1.0 > USB2: USB EHCI 1.00 > USB3: USB OHCI 1.0 > scanning bus 0 for devices... 1 USB Device(s) found > scanning bus 2 for devices... 1 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > ** Invalid partition 1 ** > scanning bus for devices... > Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0 > Type: Hard Disk > Capacity: 76319.0 MB = 74.5 GB (156301488 x 512) > Found 1 device(s). > > Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0 > Type: Hard Disk > Capacity: 76319.0 MB = 74.5 GB (156301488 x 512) > ... is now current device > Scanning scsi 0:2... > Found /extlinux/extlinux.conf > Retrieving file: /extlinux/extlinux.conf > 567 bytes read in 33 ms (16.6 KiB/s) > Ignoring unknown command: ui > Ignoring malformed menu command: autoboot > Ignoring malformed menu command: hidden > Ignoring unknown command: totaltimeout > CentOS-Userland-7-armv7hl-generic-Minimal-1810 Boot Options. > 1: CentOS-Userland-7-armv7hl-generic-Minimal-1810 > (4.14.82-201.el7.armv7hl) > > Enter choice: 1: CentOS-Userland-7-armv7hl-generic-Minimal-1810 (4.14.82- > 201.el7.armv7hl) > Retrieving file: /initramfs-4.14.82-201.el7.armv7hl.img > > Yes, this particular event is with the current Centos arm image, but > that should not matter. I have to get this Centos image built and > installed before I can test with Fedora arm image.... > > I grabbed a more recent uboot via: > > Fedora-Minimal-armhfp-30-20190301.n.0-sda > > When I try booting with the uboot in that image I get: > > U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) > DRAM: 1024 MiB > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > Trying to boot from MMC1 > > > U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology > > CPU: Allwinner A20 (SUN7I) > Model: Cubietech Cubieboard2 > I2C: ready > DRAM: 1 GiB > MMC: mmc@1c0f000: 0 > Loading Environment from FAT... ** No valid partitions found ** > In: serial > Out: serial > Err: serial > SCSI: Target spinup took 0 ms. > AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode > flags: ncq stag pm led clo only pmp pio slum part ccc apst > > Net: sunxi_set_gate: (CLK#66) unhandled > eth0: ethernet@1c50000 > starting USB... > USB0: USB EHCI 1.00 > USB1: USB OHCI 1.0 > USB2: USB EHCI 1.00 > USB3: USB OHCI 1.0 > scanning bus 0 for devices... 1 USB Device(s) found > scanning bus 1 for devices... 1 USB Device(s) found > scanning bus 2 for devices... 1 USB Device(s) found > scanning bus 3 for devices... 1 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > ** Invalid partition 1 ** > scanning bus for devices... > data abort > pc : [<7ef86b0e>] lr : [<7ef82d89>] > reloc pc : [<4a01ab0e>] lr : [<4a016d89>] > sp : 7af43ad0 ip : 0000001c fp : 000000c0 > r10: 00000000 r9 : 7af4bed8 r8 : 00000000 > r7 : 7af43d50 r6 : 7efc4894 r5 : 7efcc2f8 r4 : 7efcc2f8 > r3 : 00000000 r2 : 00000000 r1 : ea000016 r0 : 7efcc2f8 > Flags: nZcv IRQs off FIQs off Mode SVC_32 > Code: e92dbd10 f8d045f0 b0858080 1000f8d8 (f8d14604) > Resetting CPU ... > > resetting ... > > U-Boot SPL 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) > DRAM: 1024 MiB > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > Trying to boot from MMC1 > > > U-Boot 2019.04-rc2 (Feb 19 2019 - 10:00:37 +0000) Allwinner Technology > > CPU: Allwinner A20 (SUN7I) > Model: Cubietech Cubieboard2 > I2C: ready > DRAM: 1 GiB > MMC: mmc@1c0f000: 0 > Loading Environment from FAT... ** No valid partitions found ** > In: serial > Out: serial > Err: serial > > and so forth.... > > If there is a rc3 available, please tell me what image to grab for it > and I can test with that. > > Meanwhile, it seems there is a problem here. > > thanks > _______________________________________________ > arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx > To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx > Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html > List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines > List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
