On 12/5/18 5:47 PM, Stewart Samuels wrote:
BTW, another issue I found, and I don't know if it has been fixed or
not because my script does this automatically, is that with my odroid,
I begin my boot partition on disk block 3072 rather than the default
Fedorad disk block of 2048. The reason for this is that I found that
if I use the default 2048, flashing the u-boot information to the sd
or emmc cards would then corrupt the boot partition such that you can
get errors such as you are seeing now..."No block device". I have
never seen these problems since I started my partions from block 3072.
The "No block device" is the expected behavior. uboot cannot find a
partition on the uSD and then starts searching elsewhere.
I have never had a problem with the supplied images install as
provided. But then this is my 2nd non-cubieboard attempt and the other
(Linksprite_pcDuino3_Nano) which is also an Allwinner SOC.
And I have been using the install script since Paul provided it. In
fact I was STILL using his old one to my chagrin!
Stewart
On 12/5/18 2:40 PM, Robert Moskowitz wrote:
On 12/5/18 5:15 PM, Peter Robinson wrote:
U-Boot 2018.09 (Sep 11 2018 - 09:51:41 +0000) for ODROID-XU3/XU4/HC1
CPU: Exynos5422 @ 800 MHz
Model: Odroid XU3 based on EXYNOS5422
Board: Odroid XU3 based on EXYNOS5422
Type: hc1
DRAM: 2 GiB
MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 2
Loading Environment from MMC... Card did not respond to voltage
select!
*** Warning - No block device, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
MMC Device 1 not found
no mmc device at slot 1
Card did not respond to voltage select!
switch to partitions #0, OK
mmc2 is current device
** Invalid partition 1 **
starting USB...
USB0: USB EHCI 1.00
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
USB2: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning bus 2 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s)
found
scanning usb for ethernet devices... 1 Ethernet
Device(s) found
Waiting for Ethernet connection... done.
BOOTP broadcast 1
BOOTP broadcast 2
DHCP client bound to address 192.168.192.15 (5004 ms)
*** ERROR: `serverip' not set
==================================
Setup was a 4GB uSD that only had the hardkernel bootloader and
uboot.
No partitions.
Well that bit seems to be working from the details above.
sata drive (SSD) had the image (all partitions) installed. Including
changes to extlinux.conf
It finds the USB storage in the output above.
Why do you need to change the extlinux.conf? It should just work no
matter what the storage. What changes did you make?
Per
https://blog.christophersmart.com/2018/04/28/fedora-on-odroid-hc1-mini-nas-armv7/
"First things first, we need to enable the serial console, turn off
cpuidle else it won’t boot, and fix a bug where USB doesn’t load in
the
right order. We do this by mounting the boot partition on the SD card
and modifying the extlinux bootloader configuration."
sed -i "s|append|& cpuidle.off=1 \
console=tty1 console=ttySAC2,115200n8 \
rd.driver.pre=ledtrig-heartbeat,xhci-plat-hcd no_bL_switcher|" \
/run/media/rgm/__boot/extlinux/extlinux.conf
But I don't see above where it is even getting to the boot
partition on
the sata drive. But you understand this much better than I, so all
help
appreciated!
So if you interrupt the boot process can you use the U-Boot ls command
to see if it can see the contents of the first partition on the disk?
How do I interrupt boot process at the right point (I assume at the
bootp point)?
thanks
_______________________________________________
arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html
List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines
List Archives:
https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
_______________________________________________
arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html
List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines
List Archives:
https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
_______________________________________________
arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx
To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
Fedora Code of Conduct: https://getfedora.org/code-of-conduct.html
List Guidelines: https://fedoraproject.org/wiki/Mailing_list_guidelines
List Archives: https://lists.fedoraproject.org/archives/list/arm@xxxxxxxxxxxxxxxxxxxxxxx
