On Sun, Mar 18, 2018 at 12:37 AM, sakurai <sakurai@xxxxxxxxxx> wrote: > Hi Dennis and Peter, > > Of course I tried both pushing button and without it, but the result > was the same. > I remember the specification of the first version of the boot program > was designed as what you said. > I probably re-programmed the boot program according to the Ubuntu > without pushing the boot button > in order to boot from SD card. I'm not sure what we can do if you've reprogrammed it, one thing you can do is if you can boot off the OS that's on the emmc you can dd out the first few MB of the emmc to remove that version of u-boot at which it would use the one on the mSD without the need of the boot button. I've had numerous reports of F-27 GA working just fine on the BBB. Peter > 2018-03-14 1:58 GMT+09:00 Peter Robinson <pbrobinson@xxxxxxxxx>: >> On Tue, Mar 13, 2018 at 1:51 PM, sakurai <sakurai@xxxxxxxxxx> wrote: >>> 2018-03-13 8:18 GMT+09:00 Peter Robinson <pbrobinson@xxxxxxxxx>: >>>> On Mon, Mar 12, 2018 at 10:47 PM, sakurai <sakurai@xxxxxxxxxx> wrote: >>>>> Hi Peter, >>>>> >>>>> Thank you for your prompt comment. >>>>> I removed uEnv.txt but following message was displayed. >>> (snip) >>>> >>>> I don't know what you've done to now, you're likely possibly better >>>> off starting again with arm-image-installer to setup the image again >>>> with am335x_evm and then try booting with the boot button held down. >>> >>> I tried again using arm-image-installer by following command. >>> >>>> fedora-arm-image-installer --image=Fedora-Server-armhfp-27-1.6-sda.raw.xz --target=am335x_evm --media=/dev/sdd --norootpass --resizefs --addconsole --selinux=off >>> >>> Not am335x_boneblack? Anyway I installed using arm335x_evm this time. >>> >>> My boot loader may be new because Angstrom will not boot without >>> holding the boot button. >>> >>>> You might also want to give the full output. >>> >>> Here is the full output. >>> >>> U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14) >>> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) >>> musb-hdrc: MHDRC RTL version 2.0 >>> musb-hdrc: setup fifo_mode 4 >>> musb-hdrc: 28/31 max ep, 16384/16384 memory >>> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 >>> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) >>> musb-hdrc: MHDRC RTL version 2.0 >>> musb-hdrc: setup fifo_mode 4 >>> musb-hdrc: 28/31 max ep, 16384/16384 memory >>> USB Host mode controller at 47401800 using PIO, IRQ 0 >>> OMAP SD/MMC: 0 >>> mmc_send_cmd : timeout: No status update >>> reading u-boot.img >>> reading u-boot.img >>> >>> >>> U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14) >> >> As Dennis had already stated this isn't Fedora's u-boot, what you see >> is as I would expect, basically the problem here is dealing with the >> boot button correctly. _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
