2018-03-13 8:18 GMT+09:00 Peter Robinson <pbrobinson@xxxxxxxxx>: > On Mon, Mar 12, 2018 at 10:47 PM, sakurai <sakurai@xxxxxxxxxx> wrote: >> Hi Peter, >> >> Thank you for your prompt comment. >> I removed uEnv.txt but following message was displayed. (snip) > > I don't know what you've done to now, you're likely possibly better > off starting again with arm-image-installer to setup the image again > with am335x_evm and then try booting with the boot button held down. I tried again using arm-image-installer by following command. > fedora-arm-image-installer --image=Fedora-Server-armhfp-27-1.6-sda.raw.xz --target=am335x_evm --media=/dev/sdd --norootpass --resizefs --addconsole --selinux=off Not am335x_boneblack? Anyway I installed using arm335x_evm this time. My boot loader may be new because Angstrom will not boot without holding the boot button. > You might also want to give the full output. Here is the full output. U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14) musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 OMAP SD/MMC: 0 mmc_send_cmd : timeout: No status update reading u-boot.img reading u-boot.img U-Boot 2013.04-dirty (Jun 19 2013 - 09:57:14) I2C: ready DRAM: 512 MiB WARNING: Caches not enabled NAND: No NAND device found!!! 0 MiB MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 *** Warning - readenv() failed, using default environment musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Peripheral mode controller at 47401000 using PIO, IRQ 0 musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, SoftConn) musb-hdrc: MHDRC RTL version 2.0 musb-hdrc: setup fifo_mode 4 musb-hdrc: 28/31 max ep, 16384/16384 memory USB Host mode controller at 47401800 using PIO, IRQ 0 Net: <ethaddr> not set. Validating first E-fuse MAC cpsw, usb_ether Hit any key to stop autoboot: 0 gpio: pin 53 (gpio 53) value is 1 mmc0 is current device micro SD card found mmc0 is current device gpio: pin 54 (gpio 54) value is 1 SD/MMC found on device 0 reading uEnv.txt ** Unable to read file uEnv.txt ** gpio: pin 55 (gpio 55) value is 1 ** File not found /boot/uImage ** U-Boot# -- SAKURAI, Atsushi <sakurai@xxxxxxxxxx> _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
