El mar, 22-08-2017 a las 18:18 -0700, Stewart Samuels escribió:
> Dennis,
>
> How do I rebuild the initrd? I can do this on my raspberryPI 2
> running Fedora 26 if I know the procedure to do it?
you would have to use an arm device mount the filesystems, bind mount
in /dev /proc /sys chroot in, install dracut-config-generic and run
dracut to regenerate it looking at the man page or help to get the
options to install any missing modules
> In the mean time, I will try to do the modprobe. Would I do this
> within the dracut shell when the system aborts?
yes you would do it in the dracut shell
I setup a new SD card installing the released server image, and after
appending cpuidle.off=1 it booted fine
U-Boot 2017.05 (Jun 24 2017 - 16:40:39 +0000) for ODROID-XU3
CPU: Exynos5422 @ 800 MHz
Model: Odroid XU3 based on EXYNOS5422
Board: Odroid XU3 based on EXYNOS5422
Type: xu4
DRAM: 2 GiB
MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
mmc_init: -5, time 3
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:2...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
523 bytes read in 20 ms (25.4 KiB/s)
Ignoring unknown command: ui
Ignoring malformed menu command: autoboot
Ignoring malformed menu command: hidden
Ignoring unknown command: totaltimeout
Fedora-Server-armhfp-26-1.5 Boot Options.
1: Fedora-Server-armhfp-26-1.5 (4.11.8-300.fc26.armv7hl)
Enter choice: 1: Fedora-Server-armhfp-26-1.5 (4.11.8-
300.fc26.armv7hl)
Retrieving file: /initramfs-4.11.8-300.fc26.armv7hl.img
55990814 bytes read in 4195 ms (12.7 MiB/s)
Retrieving file: /vmlinuz-4.11.8-300.fc26.armv7hl
6267616 bytes read in 493 ms (12.1 MiB/s)
append: ro root=UUID=7b8bbc09-f016-489a-8288-fac9c8de58d0 cpuidle.off=1
Retrieving file: /dtb-4.11.8-300.fc26.armv7hl/exynos5422-odroidxu4.dtb
54941 bytes read in 83 ms (645.5 KiB/s)
Kernel image @ 0x42000000 [ 0x000000 - 0x5fa2e0 ]
## Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000
Loading Ramdisk to 4ca9a000, end 4ffffa1e ... OK
Loading Device Tree to 4ca89000, end 4ca9969c ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x100
[ 0.000000] Linux version 4.11.8-300.fc26.armv7hl (mockbuild@buildvm
-armv7-13.arm.fedoraproject.org) (gcc version 7.1.1 20170622 (Red Hat
7.1.1-3) (GCC) ) #1 SMP Thu Jun 29 21:24:11 UTC 2017
[ 0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7),
cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing
instruction cache
[ 0.000000] OF: fdt: Machine model: Hardkernel Odroid XU4
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: created DMA memory pool at 0xbe200000,
size 8 MiB
[ 0.000000] OF: reserved mem: initialized node region_mfc_right,
compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0xbbe00000,
size 36 MiB
[ 0.000000] OF: reserved mem: initialized node region_mfc_left,
compatible id shared-dma-pool
[ 0.000000] cma: Reserved 64 MiB at 0xb7c00000
[ 0.000000] Samsung CPU ID: 0xe5422001
[ 0.000000] Running under secure firmware.
[ 0.000000] percpu: Embedded 15 pages/cpu @eede0000 s31628 r8192
d21620 u61440
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping
on. Total pages: 505664
[ 0.000000] Kernel command line: ro root=UUID=7b8bbc09-f016-489a-
8288-fac9c8de58d0 cpuidle.off=1
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7,
524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Memory: 1874804K/2029568K available (7440K kernel code,
1301K rwdata, 3528K rodata, 2048K init, 518K bss, 89228K reserved,
65536K cma-reserved, 1177600K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0208000 - 0xc0a4408c (8433 kB)
[ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB)
[ 0.000000] .data : 0xc1000000 - 0xc1145584 (1302 kB)
[ 0.000000] .bss : 0xc1145584 - 0xc11c7160 ( 519 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8,
Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=8.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32,
nr_cpu_ids=8
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] GIC physical location is 0x10481000
[ 0.000000] Switching to timer-based delay loop, resolution 41ns
[ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000007] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps
every 89478484971ns
[ 0.007594] Console: colour dummy device 80x30
[ 0.008714] console [tty0] enabled
[ 0.008775] Calibrating delay loop (skipped), value calculated using
timer frequency.. 48.00 BogoMIPS (lpj=24000)
[ 0.008837] pid_max: default: 32768 minimum: 301
[ 0.009328] Security Framework initialized
[ 0.009365] Yama: becoming mindful.
[ 0.009411] SELinux: Initializing.
[ 0.009828] Mount-cache hash table entries: 2048 (order: 1, 8192
bytes)
[ 0.009867] Mountpoint-cache hash table entries: 2048 (order: 1,
8192 bytes)
[ 0.011168] CPU: Testing write buffer coherency: ok
[ 0.011243] ftrace: allocating 31692 entries in 62 pages
[ 0.090880] CPU0: update cpu_capacity 448
[ 0.090930] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[ 0.091693] Setting up static identity map for 0x40300000 -
0x40300098
[ 0.092453] ARM CCI driver probed
[ 0.092685] Exynos MCPM support installed
[ 0.101290] EFI services will not be available.
[ 0.102011] smp: Bringing up secondary CPUs ...
[ 0.103107] CPU1: update cpu_capacity 448
[ 0.103115] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[ 0.104260] CPU2: update cpu_capacity 448
[ 0.104269] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[ 0.105407] CPU3: update cpu_capacity 448
[ 0.105415] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[ 0.106579] CPU4: update cpu_capacity 1535
[ 0.106588] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.107844] CPU5: update cpu_capacity 1535
[ 0.107852] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.109002] CPU6: update cpu_capacity 1535
[ 0.109010] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.110165] CPU7: update cpu_capacity 1535
[ 0.110173] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.110312] smp: Brought up 1 node, 8 CPUs
[ 0.110620] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[ 0.110649] CPU: WARNING: CPU(s) started in wrong/inconsistent modes
(primary CPU mode 0x1a)
[ 0.110687] CPU: This may indicate a broken bootloader or firmware.
[ 0.113441] devtmpfs: initialized
[ 0.136821] VFP support v0.3: implementor 41 architecture 2 part 30
variant 7 rev 3
[ 0.137415] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.137479] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.141949] pinctrl core: initialized pinctrl subsystem
[ 0.145547] NET: Registered protocol family 16
[ 0.147955] DMA: preallocated 256 KiB pool for atomic coherent
allocations
[ 0.153971] No ATAGs?
[ 0.154337] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4
watchpoint registers.
[ 0.154405] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.156236] Serial: AMBA PL011 UART driver
[ 0.169418] random: fast init done
[ 0.192895] EXYNOS5420 PMU initialized
[ 0.235545] vgaarb: loaded
[ 0.236599] SCSI subsystem initialized
[ 0.237323] usbcore: registered new interface driver usbfs
[ 0.237443] usbcore: registered new interface driver hub
[ 0.237650] usbcore: registered new device driver usb
[ 0.240275] NetLabel: Initializing
[ 0.240311] NetLabel: domain hash size = 128
[ 0.240335] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.240480] NetLabel: unlabeled traffic allowed by default
[ 0.241029] clocksource: Switched to clocksource mct-frc
[ 0.343777] VFS: Disk quotas dquot_6.6.0
[ 0.343936] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[ 0.362615] NET: Registered protocol family 2
[ 0.363955] TCP established hash table entries: 8192 (order: 3,
32768 bytes)
[ 0.364148] TCP bind hash table entries: 8192 (order: 4, 65536
bytes)
[ 0.364352] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.364622] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.364695] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.365342] NET: Registered protocol family 1
[ 0.366270] Unpacking initramfs...
[ 5.774142] Freeing initrd memory: 54680K
[ 5.844438] audit: initializing netlink subsys (disabled)
[ 5.844710] audit: type=2000 audit(5.788:1): state=initialized
audit_enabled=0 res=1
[ 5.845180] Initialise system trusted keyrings
[ 5.845422] workingset: timestamp_bits=14 max_order=19
bucket_order=5
[ 5.853389] zbud: loaded
[ 6.147911] NET: Registered protocol family 38
[ 6.147946] Key type asymmetric registered
[ 6.147969] Asymmetric key parser 'x509' registered
[ 6.148128] bounce: pool size: 64 pages
[ 6.148227] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 250)
[ 6.148463] io scheduler noop registered
[ 6.148487] io scheduler deadline registered
[ 6.148887] io scheduler cfq registered (default)
[ 6.148912] io scheduler mq-deadline registered
[ 6.149588] atomic64_test: passed
[ 6.175064] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 6.188016] Serial: AMBA driver
[ 6.188372] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 58,
base_baud = 0) is a S3C6400/10
[ 6.188891] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 59,
base_baud = 0) is a S3C6400/10
[ 6.189448] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 60,
base_baud = 0) is a S3C6400/10
[ 6.942616] console [ttySAC2] enabled
[ 6.946790] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61,
base_baud = 0) is a S3C6400/10
[ 6.957384] msm_serial: driver initialized
[ 6.960394] STMicroelectronics ASC driver initialized
[ 6.969469] libphy: Fixed MDIO Bus: probed
[ 6.972858] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
[ 6.978682] ehci-pci: EHCI PCI platform driver
[ 6.983130] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.989234] ohci-pci: OHCI PCI platform driver
[ 6.993694] uhci_hcd: USB Universal Host Controller Interface driver
[ 7.000334] usbcore: registered new interface driver usbserial
[ 7.005830] usbcore: registered new interface driver
usbserial_generic
[ 7.012320] usbserial: USB Serial support registered for generic
[ 7.018520] mousedev: PS/2 mouse device common for all mice
[ 7.031679] device-mapper: uevent: version 1.0.3
[ 7.035540] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23)
initialised: dm-devel@xxxxxxxxxx
[ 7.044048] failed to register cpuidle driver
[ 7.048629] ledtrig-cpu: registered to indicate activity on CPUs
[ 7.053967] hidraw: raw HID events driver (C) Jiri Kosina
[ 7.059215] usbcore: registered new interface driver usbhid
[ 7.064502] usbhid: USB HID core driver
[ 7.071239] drop_monitor: Initializing network drop monitor service
[ 7.076334] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.081532] Initializing XFRM netlink socket
[ 7.086536] NET: Registered protocol family 10
[ 7.107078] Segment Routing with IPv6
[ 7.109372] mip6: Mobile IPv6
[ 7.112255] NET: Registered protocol family 17
[ 7.117361] ThumbEE CPU extension supported.
[ 7.120924] Registering SWP/SWPB emulation handler
[ 7.125690] big.LITTLE switcher initializing
[ 7.129931] CPU0 paired with CPU7
[ 7.133221] CPU1 paired with CPU6
[ 7.136511] CPU2 paired with CPU5
[ 7.139803] CPU3 paired with CPU4
[ 7.143100] GIC ID for CPU 0 cluster 1 is 4
[ 7.147259] GIC ID for CPU 1 cluster 1 is 5
[ 7.151418] GIC ID for CPU 2 cluster 1 is 6
[ 7.155577] GIC ID for CPU 3 cluster 1 is 7
[ 7.159736] GIC ID for CPU 0 cluster 0 is 0
[ 7.165557] IRQ54 no longer affine to CPU4
[ 7.169793] GIC ID for CPU 1 cluster 0 is 1
[ 7.177984] IRQ55 no longer affine to CPU5
[ 7.179350] GIC ID for CPU 2 cluster 0 is 2
[ 7.187498] IRQ56 no longer affine to CPU6
[ 7.191353] GIC ID for CPU 3 cluster 0 is 3
[ 7.199338] IRQ57 no longer affine to CPU7
[ 7.203698] big.LITTLE switcher initialized
[ 7.211711] registered taskstats version 1
[ 7.214667] Loading compiled-in X.509 certificates
[ 7.235598] alg: No test for pkcs1pad(rsa,sha256) (pkcs1pad(rsa-
generic,sha256))
[ 7.250626] Loaded X.509 cert 'Fedora kernel signing key:
03162a918d07b67ba6af65b45b2ec58dafb524d8'
[ 7.258448] zswap: loaded using pool lzo/zbud
[ 7.279761] Key type big_key registered
[ 7.299023] Key type encrypted registered
[ 7.336596] hctosys: unable to open rtc device (rtc0)
[ 7.340260] sr_init: No PMIC hook to init smartreflex
[ 7.346139] sr_init: platform driver register failed for SR
[ 7.352906] samsung-uart 12c20000.serial: DMA request failed, DMA
will not be used
[ 7.364349] Freeing unused kernel memory: 2048K
[ 7.367723] rodata_test: test data was not read only
[ 7.411636] systemd[1]: System time before build time, advancing
clock.
[ 7.440586] systemd[1]: systemd 233 running in system mode. (+PAM
+AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP
+GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN
default-hierarchy=hybrid)
[ 7.460108] systemd[1]: Detected architecture arm.
[ 7.464112] systemd[1]: Running in initial RAM disk.
Welcome to Fedora 26 (Server Edition) dracut-044-183.fc26 (Initramfs)!
[ 7.480205] systemd[1]: No hostname configured.
[ 7.483370] systemd[1]: Set hostname to <localhost>.
[ 7.488405] systemd[1]: Initializing machine ID from random
generator.
[ 7.940300] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 7.952524] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 7.964658] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Audit Socket.
[ 7.976229] systemd[1]: Reached target Timers.
[ OK ] Reached target Timers.
[ OK ] Listening on Journal Socket.
[ OK ] Reached target Swap.
[ OK ] Created slice System Slice.
[ OK ] Reached target Slices.
Starting Apply Kernel Variables...
Starting Setup Virtual Console...
[ OK ] Listening on Journal Socket (/dev/log).
Starting dracut cmdline hook...
[ OK ] Reached target Local File Systems.
Starting Create list of required st…ce nodes for the current
kernel...
Starting Journal Service...
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Setup Virtual Console.
[ OK ] Started Create list of required sta…vice nodes for the current
kernel.
[ 8.143378] audit: type=1130 audit(1498599911.731:2): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=kmod-static-nodes
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
Starting Create Static Device Nodes in /dev...
[ 8.188096] random: crng init done
[ OK ] Started Create Static Device Nodes in /dev.
[ 8.209520] audit: type=1130 audit(1498599911.797:3): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-tmpfiles-
setup-dev comm="systemd" exe="/usr/lib/systemd/systemd" hostname=?
addr=? terminal=? res=success'
[ OK ] Started Journal Service.
[ 8.236759] audit: type=1130 audit(1498599911.824:4): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-journald
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
[ OK ] Started dracut cmdline hook.
[ 9.263372] audit: type=1130 audit(1498599912.851:5): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-cmdline
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
Starting Open-iSCSI...
Starting dracut pre-udev hook...
[ 9.321629] Loading iSCSI transport class v2.0-870.
[ OK ] Started Open-iSCSI.
[ 9.334509] audit: type=1130 audit(1498599912.922:6): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=iscsid
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
[ 9.504725] RPC: Registered named UNIX socket transport module.
[ 9.509259] RPC: Registered udp transport module.
[ 9.513922] RPC: Registered tcp transport module.
[ 9.518600] RPC: Registered tcp NFSv4.1 backchannel transport
module.
[ 9.597623] dracut-pre-udev[344]: rpcbind:
/run/rpcbind/rpcbind.lock: No such file or directory
[ 9.902683] dracut-pre-udev[344]: rpc.idmapd: conf_reinit: open
("(null)", O_RDONLY) failed
[ 9.915135] dracut-pre-udev[344]: rpc.idmapd: conf_reinit: open
("(null)", O_RDONLY) failed
[ OK ] Started dracut pre-udev hook.
[ 10.099347] audit: type=1130 audit(1498599913.687:7): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-pre-udev
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
Starting udev Kernel Device Manager...
[ OK ] Started udev Kernel Device Manager.
[ 10.160215] audit: type=1130 audit(1498599913.746:8): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-udevd
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
Starting dracut pre-trigger hook...
[ OK ] Started dracut pre-trigger hook.
[ 10.848421] audit: type=1130 audit(1498599914.436:9): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-pre-trigger
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
Starting udev Coldplug all Devices...
Mounting Configuration File System...
[ OK ] Mounted Configuration File System.
[ OK ] Started udev Coldplug all Devices.
[ 11.461548] audit: type=1130 audit(1498599915.049:10): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-udev-
trigger comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
Starting dracut initqueue hook...
Starting Show Plymouth Boot Screen...
[ 11.693795] ehci-exynos: EHCI EXYNOS driver
[ OK ] Started Show Plymouth Bo[ 11.730091] audit: type=1130
audit(1498599915.314:11): pid=1 uid=0 auid=4294967295 ses=4294967295
subj=kernel msg='unit=plymouth-start comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
ot Screen.
[ OK ] Reached target Paths.
[ OK ] Reached target Encryp[ 11.755855] s5p-secss 10830000.sss:
s5p-sss driver registered
ted Volumes.
[ OK ] Reached target System Initialization.
[ OK ] Listening on Open-iSCSI iscsiuio Socket.
[ OK ] Reached target Sockets.
[ OK ] Started Forward Password Requests to Plymouth Directory Watch.
[ OK ] Reached target Basic System.
[ 11.834124] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply
vbus not found, using dummy regulator
[ 11.843580] ohci-exynos: OHCI EXYNOS driver
[ 11.848496] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply
vbus-boost not found, using dummy regulator
[ 11.868075] exynos-hdmi 14530000.hdmi: Failed to get supply 'vdd':
-517
[ 11.892071] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus
not found, using dummy regulator
[ 11.901041] s3c-i2c 12c80000.i2c: slave address 0x00
[ 11.902711] Synopsys Designware Multimedia Card Interface Driver
[ 11.905866] exynos-ehci 12110000.usb: EHCI Host Controller
[ 11.906355] exynos-ehci 12110000.usb: new USB bus registered,
assigned bus number 1
[ 11.923818] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz
[ 11.934889] exynos-ehci 12110000.usb: irq 71, io mem 0x12110000
[ 11.935074] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter
[ 11.936565] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply
vbus not found, using dummy regulator
[ 11.936671] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply
vbus-boost not found, using dummy regulator
[ 11.940105] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address
mode.
[ 11.978733] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[ 11.980290] dwmmc_exynos 12200000.mmc: Using internal DMA
controller.
[ 11.980308] dwmmc_exynos 12200000.mmc: Version ID is 250a
[ 11.980384] dwmmc_exynos 12200000.mmc: DW MMC controller at irq
73,64 bit host data width,64 deep fifo
[ 11.994247] exynos-rot 11c00000.rotator: The exynos rotator is
probed successfully
[ 11.996843] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address
mode.
[ 11.997154] dwmmc_exynos 12220000.mmc: Using internal DMA
controller.
[ 11.997171] dwmmc_exynos 12220000.mmc: Version ID is 250a
[ 11.997264] dwmmc_exynos 12220000.mmc: DW MMC controller at irq
74,64 bit host data width,64 deep fifo
[ 11.998889] exynos-drm-gsc 13e00000.video-scaler: failed to get
system register.
[ 11.999388] exynos-drm-gsc 13e00000.video-scaler: drm gsc registered
successfully.
[ 12.000830] exynos-drm-gsc 13e10000.video-scaler: failed to get
system register.
[ 12.001352] exynos-drm-gsc 13e10000.video-scaler: drm gsc registered
successfully.
[ 12.002677] exynos-drm-ipp exynos-drm-ipp: drm ipp registered
successfully.
[ 12.076945] usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002
[ 12.083387] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 12.090537] usb usb1: Product: EHCI Host Controller
[ 12.095375] usb usb1: Manufacturer: Linux 4.11.8-300.fc26.armv7hl
ehci_hcd
[ 12.102213] usb usb1: SerialNumber: 12110000.usb
[ 12.110520] hub 1-0:1.0: USB hub found
[ 12.112952] hub 1-0:1.0: 3 ports detected
[ 12.123321] exynos-hdmi 14530000.hdmi: Failed to get supply 'vdd':
-517
[ 12.129684] exynos-ohci 12120000.usb: USB Host Controller
[ 12.132875] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-
241330
[ 12.132886] dma-pl330 121a0000.pdma: DBUFF-32x4bytes
Num_Chans-8 Num_Peri-32 Num_Events-32
[ 12.148863] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-
241330
[ 12.148874] dma-pl330 121b0000.pdma: DBUFF-32x4bytes
Num_Chans-8 Num_Peri-32 Num_Events-32
[ 12.154459] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-
241330
[ 12.154469] dma-pl330 10800000.mdma: DBUFF-64x8bytes
Num_Chans-8 Num_Peri-1 Num_Events-32
[ 12.179312] exynos-ohci 12120000.usb: new USB bus registered,
assigned bus number 2
[ 12.186717] exynos-ohci 12120000.usb: irq 71, io mem 0x12120000
[ 12.249412] usb usb2: New USB device found, idVendor=1d6b,
idProduct=0001
[ 12.254855] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 12.262054] usb usb2: Product: USB Host Controller
[ 12.266772] usb usb2: Manufacturer: Linux 4.11.8-300.fc26.armv7hl
ohci_hcd
[ 12.273610] usb usb2: SerialNumber: 12120000.usb
[ 12.281041] hub 2-0:1.0: USB hub found
[ 12.283459] hub 2-0:1.0: 3 ports detected
[ 12.293622] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address
mode.
[ 12.299310] dwmmc_exynos 12200000.mmc: Using internal DMA
controller.
[ 12.305554] dwmmc_exynos 12200000.mmc: Version ID is 250a
[ 12.310956] dwmmc_exynos 12200000.mmc: DW MMC controller at irq
73,64 bit host data width,64 deep fifo
[ 12.322534] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address
mode.
[ 12.328291] alloc_contig_range: [b7c47, b7c48) PFNs busy
[ 12.336196] dwmmc_exynos 12220000.mmc: Using internal DMA
controller.
[ 12.341258] dwmmc_exynos 12220000.mmc: Version ID is 250a
[ 12.346678] dwmmc_exynos 12220000.mmc: DW MMC controller at irq
74,64 bit host data width,64 deep fifo
[ 12.359839] exynos-hdmi 14530000.hdmi: Failed to get supply 'vdd':
-517
[ 12.414731] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address
mode.
[ 12.420618] dwmmc_exynos 12200000.mmc: Using internal DMA
controller.
[ 12.426708] dwmmc_exynos 12200000.mmc: Version ID is 250a
[ 12.432156] dwmmc_exynos 12200000.mmc: DW MMC controller at irq
73,64 bit host data width,64 deep fifo
[ 12.445423] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address
mode.
[ 12.448628] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[ 12.457174] dwmmc_exynos 12220000.mmc: Using internal DMA
controller.
[ 12.463229] dwmmc_exynos 12220000.mmc: Version ID is 250a
[ 12.465078] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV
[ 12.472535] vdd_ldo15: Bringing 3300000uV into 3100000-3100000uV
[ 12.480560] dwmmc_exynos 12220000.mmc: DW MMC controller at irq
74,64 bit host data width,64 deep fifo
[ 12.487626] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[ 12.517641] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req
400000Hz, actual 396825HZ div = 63)
[ 12.537145] dwmmc_exynos 12220000.mmc: 1 slots initialized
[ 12.543144] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[ 12.547485] s3c-rtc 101e0000.rtc: warning: invalid RTC value so
initializing it
[ 12.554827] rtc rtc1: invalid alarm value: 1900-1-2 0:0:0
[ 12.559264] s5m-rtc s2mps14-rtc: rtc core: registered s5m-rtc as
rtc0
[ 12.569209] s3c-rtc 101e0000.rtc: rtc core: registered s3c as rtc1
[ 12.577672] exynos-tmu 10060000.tmu: More trip points than supported
by this TMU.
[ 12.583801] exynos-tmu 10060000.tmu: 2 trip points should be
configured in polling mode.
[ 12.598403] OF: graph: no port node found in /soc/hdmi@14530000
[ 12.606934] [drm] Exynos DRM: using 14450000.mixer device for DMA
mapping operations
[ 12.613816] exynos-drm exynos-drm: bound 14450000.mixer (ops
mixer_component_ops [exynosdrm])
[ 12.622627] exynos-drm exynos-drm: bound 14530000.hdmi (ops
hdmi_component_ops [exynosdrm])
[ 12.630693] exynos-drm exynos-drm: bound exynos-drm-vidi (ops
vidi_component_ops [exynosdrm])
[ 12.638669] [drm] Supports vblank timestamp caching Rev 2
(21.10.2013).
[ 12.645218] [drm] No driver support for vblank timestamp query.
[ 12.651361] [drm] Initialized exynos 1.0.0 20110530 for exynos-drm
on minor 0
[ 12.670171] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req
50000000Hz, actual 50000000HZ div = 0)
[ 12.678644] mmc0: new high speed SDHC card at address 59b4
[ 12.684385] usb_phy_generic usb_phy_generic.0.auto:
usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[ 12.684895] usb_phy_generic usb_phy_generic.2.auto:
usb_phy_generic.2.auto supply vcc not found, using dummy regulator
[ 12.685494] usb_phy_generic usb_phy_generic.3.auto:
usb_phy_generic.3.auto supply vcc not found, using dummy regulator
[ 12.711086] mmcblk0: mmc0:59b4 00000 7.37 GiB
[ 12.720799] usb_phy_generic usb_phy_generic.1.auto:
usb_phy_generic.1.auto supply vcc not found, using dummy regulator
[ 12.734693] mmcblk0: p1 p2 p3 p4
[ 12.735582] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address
mode.
[ 12.735813] dwmmc_exynos 12200000.mmc: Using internal DMA
controller.
[ 12.735832] dwmmc_exynos 12200000.mmc: Version ID is 250a
[ 12.735877] dwmmc_exynos 12200000.mmc: DW MMC controller at irq
73,64 bit host data width,64 deep fifo
[ 12.767464] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address
mode.
[ 12.773470] dwmmc_exynos 12200000.mmc: Using internal DMA
controller.
[ 12.779402] dwmmc_exynos 12200000.mmc: Version ID is 250a
[ 12.784782] dwmmc_exynos 12200000.mmc: DW MMC controller at irq
73,64 bit host data width,64 deep fifo
[ 12.791900] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 12.792355] xhci-hcd xhci-hcd.4.auto: new USB bus registered,
assigned bus number 3
[ 12.793106] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220f04c hci
version 0x100 quirks 0x02010010
[ 12.793209] xhci-hcd xhci-hcd.4.auto: irq 135, io mem 0x12000000
[ 12.793548] usb usb3: New USB device found, idVendor=1d6b,
idProduct=0002
[ 12.793558] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 12.793566] usb usb3: Product: xHCI Host Controller
[ 12.793573] usb usb3: Manufacturer: Linux 4.11.8-300.fc26.armv7hl
xhci-hcd
[ 12.793580] usb usb3: SerialNumber: xhci-hcd.4.auto
[ 12.794679] hub 3-0:1.0: USB hub found
[ 12.794751] hub 3-0:1.0: 1 port detected
[ 12.795499] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
[ 12.795868] xhci-hcd xhci-hcd.4.auto: new USB bus registered,
assigned bus number 4
[ 12.796112] usb usb4: We don't know the algorithms for LPM for this
host, disabling LPM.
[ 12.796354] usb usb4: New USB device found, idVendor=1d6b,
idProduct=0003
[ 12.796364] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 12.796372] usb usb4: Product: xHCI Host Controller
[ 12.796379] usb usb4: Manufacturer: Linux 4.11.8-300.fc26.armv7hl
xhci-hcd
[ 12.796386] usb usb4: SerialNumber: xhci-hcd.4.auto
[ 12.797484] hub 4-0:1.0: USB hub found
[ 12.797553] hub 4-0:1.0: 1 port detected
[ 12.798344] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 12.798712] xhci-hcd xhci-hcd.5.auto: new USB bus registered,
assigned bus number 5
[ 12.799384] xhci-hcd xhci-hcd.5.auto: hcc params 0x0220f04c hci
version 0x100 quirks 0x02010010
[ 12.799468] xhci-hcd xhci-hcd.5.auto: irq 136, io mem 0x12400000
[ 12.799801] usb usb5: New USB device found, idVendor=1d6b,
idProduct=0002
[ 12.799812] usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 12.799820] usb usb5: Product: xHCI Host Controller
[ 12.799827] usb usb5: Manufacturer: Linux 4.11.8-300.fc26.armv7hl
xhci-hcd
[ 12.799834] usb usb5: SerialNumber: xhci-hcd.5.auto
[ 12.801066] hub 5-0:1.0: USB hub found
[ 12.801139] hub 5-0:1.0: 1 port detected
[ 12.801633] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller
[ 12.801950] xhci-hcd xhci-hcd.5.auto: new USB bus registered,
assigned bus number 6
[ 12.802159] usb usb6: We don't know the algorithms for LPM for this
host, disabling LPM.
[ 12.802399] usb usb6: New USB device found, idVendor=1d6b,
idProduct=0003
[ 12.802410] usb usb6: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 12.802417] usb usb6: Product: xHCI Host Controller
[ 12.802425] usb usb6: Manufacturer: Linux 4.11.8-300.fc26.armv7hl
xhci-hcd
[ 12.802432] usb usb6: SerialNumber: xhci-hcd.5.auto
[ 12.803399] hub 6-0:1.0: USB hub found
[ 12.803466] hub 6-0:1.0: 1 port detected
[ OK ] Found de[ 13.046711] dwmmc_exynos 12200000.mmc: IDMAC
supports 32-bit address mode.
[ 13.053682] alloc_contig_range: [b7c49, b7c4a) PFNs busy
[ 13.058976] dwmmc_exynos 12200000.mmc: Using internal DMA
controller.
[ 13.065226] dwmmc_exynos 12200000.mmc: Version ID is 250a
[ 13.070664] dwmmc_exynos 12200000.mmc: DW MMC controller at irq
73,64 bit host data width,64 deep fifo
vice /dev/disk/by-uuid/7b8bbc09-f016-489a-8288-fac9c8de58d0.
[ OK ] Reached target Initrd Root Device.
[ OK 13.110810] audit: type=1130 audit(1498599916.698:12): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-
initqueue comm="systemd" exe="/usr/lib/systemd/systemd" hostname=?
addr=? terminal=? res=success'
0m] Started dracut initqueue hook.
Starting dracut pre-mount hook...
[ OK ] Reached target Remote File Systems (Pre).
[ OK ] Reached target Remote File Systems.
[ OK 13.260087] audit: type=1130 audit(1498599916.847:13): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-pre-
mount comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
0m] Started dracut pre-mount hook.
Starting File System Check on /dev/…c09-f016-489a-8288-
fac9c8de58d0...
[ OK 13.415704] audit: type=1130 audit(1498599917.003:14): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-
fsck-root comm="systemd" exe="/usr/lib/systemd/systemd" hostname=?
addr=? terminal=? res=success'
0m] Started File System Check on /dev/d…bbc09-f016-489a-8288-
fac9c8de58d0.
Mounting /sysroot...
[ 13.676603] SGI XFS with ACLs, security attributes, no debug enabled
[ 13.698391] XFS (mmcblk0p4): Mounting V5 Filesystem
[ 14.326779] XFS (mmcblk0p4): Ending clean mount
[ OK ] Mounted /sysroot.
[ OK ] Reached target Initrd Root File System.
Starting Reload Configuration from the Real Root...
[ OK 15.154176] audit: type=1130 audit(1498599918.742:15): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=initrd-
parse-etc comm="systemd" exe="/usr/lib/systemd/systemd" hostname=?
addr=? terminal=? res=success'
[ 15.173881] audit: type=1131 audit(1498599918.742:16): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=initrd-parse-etc
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
0m] Started Reload Configuration from the Real Root.
[ OK ] Reached target Initrd File Systems.
[ OK ] Reached target Initrd Default Target.
Starting dracut pre-pivot and cleanup hook...
[ 15.279632] usb usb3-port1: connect-debounce failed
[ OK 15.899414] audit: type=1130 audit(1498599919.487:17): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-pre-
pivot comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
[ 15.904966] dma-pl330 3880000.adma: Loaded driver for PL330 DMAC-
241330
[ 15.905074] dma-pl330 3880000.adma: DBUFF-4x8bytes Num_Chans-6
Num_Peri-16 Num_Events-6
[ 15.910090] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address
mode.
[ 15.918252] dwmmc_exynos 12200000.mmc: Using internal DMA
controller.
[ 15.918272] dwmmc_exynos 12200000.mmc: Version ID is 250a
[ 15.918322] dwmmc_exynos 12200000.mmc: DW MMC controller at irq
73,64 bit host data width,64 deep fifo
0m] Started dracut pre-pivot and cleanup hook.
Starting Cleaning Up and Shutting Down Daemons...
[ OK ] Stopped target Timers.
Starting Setup Virtual Console...
[ 16.011318] audit: type=1131 audit(1498599919.597:18): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-pre-pivot
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
Starting Plymouth switch root service...
[ OK ] Stopped dracut pre-pivot and cleanup hoo[ 16.040472] audit:
type=1130 audit(1498599919.625:19): pid=1 uid=0 auid=4294967295
ses=4294967295 subj=kernel msg='unit=systemd-sysctl comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
[ 16.059276] audit: type=1131 audit(1498599919.625:20): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-sysctl
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
k.
[ O[ 16.059898] audit: type=1130 audit(1498599919.647:21): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-pre-
mount comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
[ 16.059976] audit: type=1131 audit(1498599919.647:22): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-pre-mount
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
K ] Stopped target Initrd Default Target.
[ 16.125953] audit: type=1130 audit(1498599919.713:23): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-initqueue
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
[ 16.145251] audit: type=1131 audit(1498599919.714:24): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut-initqueue
comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
[ 16.165087] audit: type=1130 audit(1498599919.733:25): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=kernel msg='unit=systemd-udev-
trigger comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=?
terminal=? res=success'
m OK ] Sto[ 16.165113] audit: type=1131 audit(1498599919.733:26):
pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel
msg='unit=systemd-udev-trigger comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
pped target Initrd Root Device.
[ OK ] Stopped target Basic System.
[ OK ] Stopped target Sockets.
[ OK ] Closed Open-iSCSI iscsiuio Socket.
[ OK ] Stopped target System Initialization.
[ OK ] Stopped Apply Kernel Variables.
[ OK ] Stopped target Swap.
[ OK ] Stopped target Slices.
[ OK ] Stopped dracut pre-mount hook.
[ OK ] Stopped target Encrypted Volumes.
[ OK ] Stopped target Remote File Systems.
[ OK ] Stopped target Remote File Systems (Pre).
[ OK ] Stopped dracut initqueue hook.
[ OK ] Stopped udev Coldplug all Devices.
[ OK ] Stopped dracut pre-trigger hook.
Stopping udev Kernel Device Manager...
Stopping Open-iSCSI...
[ OK ] Stopped target Local File Systems.
[ OK ] Stopped target Paths.
[ OK ] Stopped udev Kernel Device Manager.
[ OK ] Started Setup Virtual Console.
[ OK ] Started Plymouth switch root service.
[ OK ] Stopped Open-iSCSI.
[ OK ] Stopped dracut pre-udev hook.
[ OK ] Stopped dracut cmdline hook.
[ OK ] Stopped Create Static Device Nodes in /dev.
[ OK ] Stopped Create list of required sta…vice nodes for the current
kernel.
[ OK ] Closed udev Kernel Socket.
[ OK ] Closed udev Control Socket.
Starting Cleanup udevd DB...
[ OK ] Started Cleaning Up and Shutting Down Daemons.
[ OK ] Started Cleanup udevd DB.
[ OK ] Reached target Switch Root.
Starting Switch Root...
[ 16.477957] systemd-journald[222]: Received SIGTERM from PID 1
(systemd).
[ 16.886362] systemd: 17 output lines suppressed due to ratelimiting
[ 18.126756] SELinux: Class sctp_socket not defined in policy.
[ 18.131191] SELinux: Class icmp_socket not defined in policy.
[ 18.137005] SELinux: Class ax25_socket not defined in policy.
[ 18.142782] SELinux: Class ipx_socket not defined in policy.
[ 18.148500] SELinux: Class netrom_socket not defined in policy.
[ 18.154480] SELinux: Class atmpvc_socket not defined in policy.
[ 18.160459] SELinux: Class x25_socket not defined in policy.
[ 18.166177] SELinux: Class rose_socket not defined in policy.
[ 18.172008] SELinux: Class decnet_socket not defined in policy.
[ 18.177962] SELinux: Class atmsvc_socket not defined in policy.
[ 18.183941] SELinux: Class rds_socket not defined in policy.
[ 18.189660] SELinux: Class irda_socket not defined in policy.
[ 18.195467] SELinux: Class pppox_socket not defined in policy.
[ 18.201358] SELinux: Class llc_socket not defined in policy.
[ 18.207078] SELinux: Class can_socket not defined in policy.
[ 18.212797] SELinux: Class tipc_socket not defined in policy.
[ 18.218603] SELinux: Class bluetooth_socket not defined in policy.
[ 18.224842] SELinux: Class iucv_socket not defined in policy.
[ 18.230649] SELinux: Class rxrpc_socket not defined in policy.
[ 18.236540] SELinux: Class isdn_socket not defined in policy.
[ 18.242526] SELinux: Class phonet_socket not defined in policy.
[ 18.248325] SELinux: Class ieee802154_socket not defined in policy.
[ 18.254653] SELinux: Class caif_socket not defined in policy.
[ 18.260456] SELinux: Class alg_socket not defined in policy.
[ 18.266176] SELinux: Class nfc_socket not defined in policy.
[ 18.271895] SELinux: Class vsock_socket not defined in policy.
[ 18.277787] SELinux: Class kcm_socket not defined in policy.
[ 18.283506] SELinux: Class qipcrtr_socket not defined in policy.
[ 18.289573] SELinux: Class smc_socket not defined in policy.
[ 18.295292] SELinux: the above unknown classes and permissions will
be allowed
[ 18.419669] systemd[1]: Successfully loaded SELinux policy in
1.045771s.
[ 18.803799] systemd[1]: Relabelled /dev and /run in 240.195ms.
Welcome to Fedora 26 (Server Edition)!
[ OK ] Stopped Switch Root.
[ OK ] Stopped Journal Service.
Starting Journal Service...
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ OK ] Listening on udev Control Socket.
[ OK ] Created slice system-sshd\x2dkeygen.slice.
[ OK ] Created slice system-getty.slice.
[ OK ] Stopped target Switch Root.
[ OK ] Stopped target Initrd File Systems.
[ OK ] Stopped target Initrd Root File System.
Starting Create list of required st…ce nodes for the current
kernel...
[ OK ] Created slice system-serial\x2dgetty.slice.
Mounting POSIX Message Queue File System...
[ OK ] Listening on Device-mapper event daemon FIFOs.
[ OK ] Reached target rpc_pipefs.target.
Starting Setup Virtual Console...
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on LVM2 metadata daemon socket.
[ OK ] Listening on LVM2 poll daemon socket.
[ OK ] Listening on Process Core Dump Socket.
[ OK ] Reached target Paths.
[ OK ] Created slice User and Session Slice.
[ OK ] Reached target Slices.
[ OK ] Listening on udev Kernel Socket.
Starting Monitoring of LVM2 mirrors…ng dmeventd or progress
polling...
Starting Apply Kernel Variables...
[ OK ] Set up automount Arbitrary Executab…rmats File System
Automount Point.
Mounting Debug File System...
[ OK ] Stopped File System Check on Root Device.
Starting Remount Root and Kernel File Systems...
[ OK ] Mounted Debug File System.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Started Journal Service.
[ OK ] Started Create list of required sta…vice nodes for the current
kernel.
[ OK ] Started Apply Kernel Variables.
[ OK ] Started LVM2 metadata daemon.
[ OK ] Started Remount Root and Kernel File Systems.
Starting udev Coldplug all Devices...
Starting Flush Journal to Persistent Storage...
Starting Create Static Device Nodes in /dev...
Starting Configure read-only root support...
[ 20.480348] systemd-journald[676]: Received request to flush runtime
journal from PID 1
[ 20.681784] systemd-journald[676]: File
/var/log/journal/97e60d4efcaf4302880532e97752f587/system.journal
corrupted or uncleanly shut down, renaming and replacing.
[ OK ] Started Setup Virtual Console.
[ OK 20.985859] kauditd_printk_skb: 40 callbacks suppressed
[ 20.990463] audit: type=1130 audit(1498599924.573:67): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=fedora-readonly comm="systemd" exe="/usr/lib/systemd/systemd"
hostname=? addr=? terminal=? res=success'
0m] Started Configure read-only root support.
Starting Load/Save Random Seed...
[ OK 21.024637] audit: type=1130 audit(1498599924.612:68): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=systemd-tmpfiles-setup-dev comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
m] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
[ OK ] Started Load/Save Random Seed.
[ 21.074691] audit: type=1130 audit(1498599924.658:69): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=systemd-random-seed comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
[ OK 21.158352] audit: type=1130 audit(1498599924.746:70): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=systemd-journal-flush comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
0m] Started Flush Journal to Persistent Storage.
[ OK 21.486290] audit: type=1130 audit(1498599925.074:71): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=systemd-udev-trigger comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
0m] Started udev Coldplug all Devices.
Starting udev Wait for Complete Device Initialization...
[ OK 22.472347] audit: type=1130 audit(1498599926.060:72): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=systemd-udevd comm="systemd" exe="/usr/lib/systemd/systemd"
hostname=? addr=? terminal=? res=success'
0m] Started udev Kernel Device Manager.
[ 23.040068] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address
mode.
[ 23.045833] dwmmc_exynos 12200000.mmc: Using internal DMA
controller.
[ 23.052090] dwmmc_exynos 12200000.mmc: Version ID is 250a
[ 23.059702] dwmmc_exynos 12200000.mmc: DW MMC controller at irq
73,64 bit host data width,64 deep fifo
[ 23.070530] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[ 23.090821] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req
400000Hz, actual 396825HZ div = 63)
[ 23.110215] dwmmc_exynos 12200000.mmc: 1 slots initialized
[ 23.285490] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset
disabled, irq disabled
[ 23.330471] exynos-nocp: new NoC Probe device registered:
10ca1000.nocp
[ 23.340685] media: Linux media interface: v0.10
[ 23.345210] exynos-nocp: new NoC Probe device registered:
10ca1400.nocp
[ 23.355296] exynos-nocp: new NoC Probe device registered:
10ca1800.nocp
[ 23.362860] exynos-nocp: new NoC Probe device registered:
10ca1c00.nocp
[ 23.457606] Linux video capture interface: v2.00
[ OK ] Found device /dev/ttySAC2.
[ 23.783328] platform 11000000.codec:left: assigned reserved memory
node region_mfc_left
[ OK ] Found device /dev/disk/by-uuid/444ba0f3-9123-4bf8-9786-
98906faf18f6.
Activating swap [ 23.816915] platform 11000000.codec:right:
assigned reserved memory node region_mfc_right
/dev/disk/by-uuid/4…0f3-9123-4bf8-9786-98906faf18f6...
[ 23.831188] s5p-mfc 11000000.codec: decoder registered as
/dev/video0
[ 23.874094] s5p-mfc 11000000.codec: encoder registered as
/dev/video1
[ 23.917279] s5p-jpeg 11f50000.jpeg: encoder device registered as
/dev/video2
[ 23.917954] Adding 499708k swap on /dev/mmcblk0p3. Priority:-1
extents:1 across:499708k SSFS
[ 23.945363] s5p-jpeg 11f50000.jpeg: decoder device registered as
/dev/video3
[ 23.951084] s5p-jpeg 11f50000.jpeg: Samsung S5P JPEG codec
[ OK ] Activated swap /dev/disk/by-uuid/444ba0f3-9123-4bf8-9786-
98906faf18f6.
[ OK ] Found devi[ 23.995548] s5p-jpeg 11f60000.jpeg: encoder
device registered as /dev/video4
ce /dev/disk/b[ 24.004242] s5p-jpeg 11f60000.jpeg: decoder device
registered as /dev/video5
[ 24.010727] s5p-jpeg 11f60000.jpeg: Samsung S5P JPEG codec
y-uuid/0377ede3-065f-4468-b58c-41f39718981f.
[ OK ] Reached target Swap.
[ OK ] Started Mo[ 24.032740] audit: type=1130
audit(1498599927.620:73): pid=1 uid=0 auid=4294967295 ses=4294967295
subj=system_u:system_r:init_t:s0 msg='unit=lvm2-monitor comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
nitoring of LVM2 mirrors,…sing dmeventd or progress polling.
[ 24.086157] exynos-bus soc:bus_wcore: devfreq_add_device: Unable to
find governor for the device
[ 24.097637] devfreq devfreq0: releasing devfreq which doesn't exist
[ 24.102614] exynos-bus soc:bus_wcore: failed to add devfreq device
[ 24.109595] exynos-bus: probe of soc:bus_wcore failed with error -12
[ OK[ 37.646891] audit: type=1130 audit(1498599941.234:74): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=systemd-udev-settle comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
] Started udev Wait for Complete Device Initialization.
Starting Activation of DM RAID sets...
[ OK 37.845774] audit: type=1130 audit(1498599941.433:75): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=dmraid-activation comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
[ 37.867447] audit: type=1131 audit(1498599941.433:76): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=dmraid-activation comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
0m] Started Activation of DM RAID sets.
[ OK ] Reached target Local File Systems (Pre).
Mounting /boot...
[ OK ] Reached target Encrypted Volumes.
[ 37.925384] EXT4-fs (mmcblk0p2): mounted filesystem with ordered
data mode. Opts: (null)
[ OK ] Mounted /boot.
[ OK ] Reached target Local File Systems.
Starting Restore /run/initramfs on shutdown...
Starting Tell Plymouth To Write Out Runtime Data...
Starting Preprocess NFS configuration...
Starting Import network configuration from initramfs...
[ OK 37.995422] audit: type=1130 audit(1498599941.583:77): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=dracut-shutdown comm="systemd" exe="/usr/lib/systemd/systemd"
hostname=? addr=? terminal=? res=success'
0m] Started Restore /run/initramfs on shutdown.
[ OK 38.032194] audit: type=1130 audit(1498599941.620:78): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=plymouth-read-write comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
[ 38.053416] audit: type=1131 audit(1498599941.620:79): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=plymouth-read-write comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
0m] Started Te[ 38.076869] audit: type=1130 audit(1498599941.664:80):
pid=1 uid=0 auid=4294967295 ses=4294967295
subj=system_u:system_r:init_t:s0 msg='unit=nfs-config comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
[ 38.097697] audit: type=1131 audit(1498599941.664:81): pid=1 uid=0
auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=nfs-config comm="systemd" exe="/usr/lib/systemd/systemd"
hostname=? addr=? terminal=? res=success'
ll Plymouth To Write Out Runtime Data.
[ OK ] Started Preprocess NFS configuration.
[ OK 38.250750] audit: type=1130 audit(1498599941.838:82): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=fedora-import-state comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
0m] Started Import network configuration from initramfs.
Starting Create Volatile Files and Directories...
[ OK 38.605272] audit: type=1130 audit(1498599942.193:83): pid=1
uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:init_t:s0
msg='unit=systemd-tmpfiles-setup comm="systemd"
exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=?
res=success'
0m] Started Create Volatile Files and Directories.
Starting Security Auditing Service...
[ OK ] Started Security Auditing Service.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Listening on Open-iSCSI iscsid Socket.
[ OK ] Started Updates mlocate database every day.
[ OK ] Listening on PC/SC Smart Card Daemon Activation Socket.
[ OK ] Listening on Open-iSCSI iscsiuio Socket.
[ OK ] Listening on Cockpit Web Service Socket.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Started dnf makecache timer.
[ OK ] Reached target Timers.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started Self Monitoring and Reporting Technology (SMART)
Daemon.
Starting Initial Setup configuration program...
[ OK ] Started irqbalance daemon.
Starting System Security Services Daemon...
[ OK ] Started D-Bus System Message Bus.
Starting System Logging Service...
Starting GSSAPI Proxy Daemon...
Starting ABRT Automated Bug Reporting Tool...
Starting NTP client/server...
Starting Authorization Manager...
[ OK ] Reached target sshd-keygen.target.
[ OK ] Started Hardware RNG Entropy Gatherer Daemon.
[ 48.753734] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 49.047719] Ebtables v2.0 registered
[ 49.798147] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 50.798282] bridge: filtering via arp/ip/ip6tables is no longer
available by default. Update your scripts to load br_netfilter if you
need this.
[ 51.590603] Netfilter messages via NETLINK v0.30.
[ 51.668881] ip_set: protocol 6
Fedora 26 (Server Edition)
Kernel 4.11.8-300.fc26.armv7hl on an armv7l (ttySAC2)
Admin Console: https://127.0.0.1:9090/ or https://[::ffff:127.0.0.1]:90
90/
localhost login:Attachment:
signature.asc
Description: This is a digitally signed message part
_______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
