|
Hello Dennis, The parameter you provided me below was incorrect (spelling error). I used cpuidle.off=1 and the system now boot much further, but eventually goes into a: dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scriptsloop and never completes the boot process. Any other suggestions? See the output from the serial port that follows: ----------------------------------------------------------------------------------------------------- U-Boot 2017.05 (Jun 24 2017 - 16:40:39 +0000) for ODROID-XU3 CPU: Exynos5422 @ 800 MHz Model: Odroid XU3 based on EXYNOS5422 Board: Odroid XU3 based on EXYNOS5422 Type: xu4 DRAM: 2 GiB MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 Card did not respond to voltage select! mmc_init: -95, time 11 switch to partitions #0, OK mmc0(part 0) is current device Scanning mmc 0:2... Found /extlinux/extlinux.conf Retrieving file: /extlinux/extlinux.conf 527 bytes read in 14 ms (36.1 KiB/s) Ignoring unknown command: ui Ignoring malformed menu command: autoboot Ignoring malformed menu command: hidden Ignoring unknown command: totaltimeout Fedora-Mate-armhfp-26-1.5 Boot Options. 1: Fedora-Mate-armhfp-26-1.5 (4.11.8-300.fc26.armv7hl) Enter choice: 1: Fedora-Mate-armhfp-26-1.5 (4.11.8-300.fc26.armv7hl) Retrieving file: /initramfs-4.11.8-300.fc26.armv7hl.img 55227208 bytes read in 2480 ms (21.2 MiB/s) Retrieving file: /vmlinuz-4.11.8-300.fc26.armv7hl 6267616 bytes read in 306 ms (19.5 MiB/s) append: ro root=UUID=11cf09b5-43b2-4588-969d-550b4e2af055 cpuidle.off=1 cma=192MB Retrieving file: /dtb-4.11.8-300.fc26.armv7hl/exynos5422-odroidxu4.dtb 54941 bytes read in 52 ms (1 MiB/s) Kernel image @ 0x42000000 [ 0x000000 - 0x5fa2e0 ] ## Flattened Device Tree blob at 43000000 Booting using the fdt blob at 0x43000000 Loading Ramdisk to 4cb54000, end 4ffff348 ... OK Loading Device Tree to 4cb43000, end 4cb5369c ... OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x100 [ 0.000000] Linux version 4.11.8-300.fc26.armv7hl (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 7.1.1 201707 [ 0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Hardkernel Odroid XU4 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created DMA memory pool at 0xbe200000, size 8 MiB [ 0.000000] OF: reserved mem: initialized node region_mfc_right, compatible id shared-dma-pool [ 0.000000] Reserved memory: created DMA memory pool at 0xbbe00000, size 36 MiB [ 0.000000] OF: reserved mem: initialized node region_mfc_left, compatible id shared-dma-pool [ 0.000000] cma: Reserved 192 MiB at 0xafc00000 [ 0.000000] Samsung CPU ID: 0xe5422001 [ 0.000000] Running under secure firmware. [ 0.000000] percpu: Embedded 15 pages/cpu @eede0000 s31628 r8192 d21620 u61440 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 505664 [ 0.000000] Kernel command line: ro root=UUID=11cf09b5-43b2-4588-969d-550b4e2af055 cpuidle.off=1 cma=192MB [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 1744476K/2029568K available (7440K kernel code, 1301K rwdata, 3528K rodata, 2048K init, 518K bss, 88484K ) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0a4408c (8433 kB) [ 0.000000] .init : 0xc0e00000 - 0xc1000000 (2048 kB) [ 0.000000] .data : 0xc1000000 - 0xc1145584 (1302 kB) [ 0.000000] .bss : 0xc1145584 - 0xc11c7160 ( 519 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=8. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=8 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] GIC physical location is 0x10481000 [ 0.000000] Switching to timer-based delay loop, resolution 41ns [ 0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.000007] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns [ 0.007591] Console: colour dummy device 80x30 [ 0.008713] console [tty0] enabled [ 0.008774] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000) [ 0.008835] pid_max: default: 32768 minimum: 301 [ 0.009324] Security Framework initialized [ 0.009361] Yama: becoming mindful. [ 0.009408] SELinux: Initializing. [ 0.009826] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.009867] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.011169] CPU: Testing write buffer coherency: ok [ 0.011245] ftrace: allocating 31692 entries in 62 pages [ 0.090906] CPU0: update cpu_capacity 448 [ 0.090956] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100 [ 0.091722] Setting up static identity map for 0x40300000 - 0x40300098 [ 0.092479] ARM CCI driver probed [ 0.092713] Exynos MCPM support installed [ 0.101325] EFI services will not be available. [ 0.102047] smp: Bringing up secondary CPUs ... [ 0.103139] CPU1: update cpu_capacity 448 [ 0.103147] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101 [ 0.104319] CPU2: update cpu_capacity 448 [ 0.104327] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102 [ 0.105462] CPU3: update cpu_capacity 448 [ 0.105470] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103 [ 0.106648] CPU4: update cpu_capacity 1535 [ 0.106657] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.107903] CPU5: update cpu_capacity 1535 [ 0.107911] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.109069] CPU6: update cpu_capacity 1535 [ 0.109078] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.110219] CPU7: update cpu_capacity 1535 [ 0.110227] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.110367] smp: Brought up 1 node, 8 CPUs [ 0.110677] SMP: Total of 8 processors activated (384.00 BogoMIPS). [ 0.110705] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x1a) [ 0.110743] CPU: This may indicate a broken bootloader or firmware. [ 0.113492] devtmpfs: initialized [ 0.136911] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 3 [ 0.137504] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns [ 0.137567] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.149473] pinctrl core: initialized pinctrl subsystem [ 0.153110] NET: Registered protocol family 16 [ 0.155566] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.161569] No ATAGs? [ 0.161913] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.161981] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.163819] Serial: AMBA PL011 UART driver [ 0.169473] random: fast init done [ 0.200419] EXYNOS5420 PMU initialized [ 0.242967] vgaarb: loaded [ 0.244031] SCSI subsystem initialized [ 0.244774] usbcore: registered new interface driver usbfs [ 0.244893] usbcore: registered new interface driver hub [ 0.245111] usbcore: registered new device driver usb [ 0.247788] NetLabel: Initializing [ 0.247826] NetLabel: domain hash size = 128 [ 0.247850] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.247960] NetLabel: unlabeled traffic allowed by default [ 0.248528] clocksource: Switched to clocksource mct-frc [ 0.351325] VFS: Disk quotas dquot_6.6.0 [ 0.351485] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.370155] NET: Registered protocol family 2 [ 0.371485] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.371691] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.371893] TCP: Hash tables configured (established 8192 bind 8192) [ 0.372167] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.372239] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.372890] NET: Registered protocol family 1 [ 0.373826] Unpacking initramfs... [ 4.732409] Freeing initrd memory: 53936K [ 4.804263] audit: initializing netlink subsys (disabled) [ 4.804481] audit: type=2000 audit(4.748:1): state=initialized audit_enabled=0 res=1 [ 4.804946] Initialise system trusted keyrings [ 4.805183] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 4.813102] zbud: loaded [ 5.107473] NET: Registered protocol family 38 [ 5.107512] Key type asymmetric registered [ 5.107602] Asymmetric key parser 'x509' registered [ 5.107694] bounce: pool size: 64 pages [ 5.107791] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250) [ 5.108020] io scheduler noop registered [ 5.108043] io scheduler deadline registered [ 5.108441] io scheduler cfq registered (default) [ 5.108465] io scheduler mq-deadline registered [ 5.109078] atomic64_test: passed [ 5.134056] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 5.143635] Serial: AMBA driver [ 5.143928] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 58, base_baud = 0) is a S3C6400/10 [ 5.144342] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 59, base_baud = 0) is a S3C6400/10 [ 5.144745] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 60, base_baud = 0) is a S3C6400/10 [ 5.898934] console [ttySAC2] enabled [ 5.902981] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10 [ 5.913583] msm_serial: driver initialized [ 5.916619] STMicroelectronics ASC driver initialized [ 5.925886] libphy: Fixed MDIO Bus: probed [ 5.929367] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 5.935100] ehci-pci: EHCI PCI platform driver [ 5.939602] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 5.945651] ohci-pci: OHCI PCI platform driver [ 5.950121] uhci_hcd: USB Universal Host Controller Interface driver [ 5.956765] usbcore: registered new interface driver usbserial [ 5.962235] usbcore: registered new interface driver usbserial_generic [ 5.968733] usbserial: USB Serial support registered for generic [ 5.974929] mousedev: PS/2 mouse device common for all mice [ 5.988066] device-mapper: uevent: version 1.0.3 [ 5.991921] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@xxxxxxxxxx [ 6.000408] failed to register cpuidle driver [ 6.005053] ledtrig-cpu: registered to indicate activity on CPUs [ 6.010350] hidraw: raw HID events driver (C) Jiri Kosina [ 6.015608] usbcore: registered new interface driver usbhid [ 6.020886] usbhid: USB HID core driver [ 6.027682] drop_monitor: Initializing network drop monitor service [ 6.032810] ip_tables: (C) 2000-2006 Netfilter Core Team [ 6.037978] Initializing XFRM netlink socket [ 6.042966] NET: Registered protocol family 10 [ 6.063610] Segment Routing with IPv6 [ 6.065901] mip6: Mobile IPv6 [ 6.068788] NET: Registered protocol family 17 [ 6.073899] ThumbEE CPU extension supported. [ 6.077453] Registering SWP/SWPB emulation handler [ 6.082220] big.LITTLE switcher initializing [ 6.086462] CPU0 paired with CPU7 [ 6.089751] CPU1 paired with CPU6 [ 6.093041] CPU2 paired with CPU5 [ 6.096334] CPU3 paired with CPU4 [ 6.099630] GIC ID for CPU 0 cluster 1 is 4 [ 6.103789] GIC ID for CPU 1 cluster 1 is 5 [ 6.107948] GIC ID for CPU 2 cluster 1 is 6 [ 6.112107] GIC ID for CPU 3 cluster 1 is 7 [ 6.116267] GIC ID for CPU 0 cluster 0 is 0 [ 6.122086] IRQ54 no longer affine to CPU4 [ 6.127324] GIC ID for CPU 1 cluster 0 is 1 [ 6.135604] IRQ55 no longer affine to CPU5 [ 6.139319] GIC ID for CPU 2 cluster 0 is 2 [ 6.147667] IRQ56 no longer affine to CPU6 [ 6.151813] GIC ID for CPU 3 cluster 0 is 3 [ 6.159788] IRQ57 no longer affine to CPU7 [ 6.164315] big.LITTLE switcher initialized [ 6.172209] registered taskstats version 1 [ 6.175295] Loading compiled-in X.509 certificates [ 6.196506] alg: No test for pkcs1pad(rsa,sha256) (pkcs1pad(rsa-generic,sha256)) [ 6.211622] Loaded X.509 cert 'Fedora kernel signing key: 03162a918d07b67ba6af65b45b2ec58dafb524d8' [ 6.219446] zswap: loaded using pool lzo/zbud [ 6.240940] Key type big_key registered [ 6.260362] Key type encrypted registered [ 6.297985] hctosys: unable to open rtc device (rtc0) [ 6.301652] sr_init: No PMIC hook to init smartreflex [ 6.307608] sr_init: platform driver register failed for SR [ 6.314282] samsung-uart 12c20000.serial: DMA request failed, DMA will not be used [ 6.325695] Freeing unused kernel memory: 2048K [ 6.329074] rodata_test: test data was not read only [ 6.372735] systemd[1]: System time before build time, advancing clock. [ 6.401997] systemd[1]: systemd 233 running in system mode. (+PAM +AUDIT +SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP +LIBC) [ 6.421489] systemd[1]: Detected architecture arm. [ 6.425542] systemd[1]: Running in initial RAM disk. Welcome to Fedora 26 (Twenty Six) dracut-044-183.fc26 (Initramfs)! [ 6.440745] systemd[1]: No hostname configured. [ 6.443912] systemd[1]: Set hostname to <localhost>. [ 6.448948] systemd[1]: Initializing machine ID from random generator. [ 6.913011] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ 6.922083] systemd[1]: Listening on Journal Socket (/dev/log). [ OK ] Listening on Journal Socket (/dev/log). [ 6.935762] systemd[1]: Reached target Timers. [ OK ] Reached target Timers. [ 6.946731] systemd[1]: Reached target Local File Systems. [ OK ] Reached target Local File Systems. [ OK ] Listening on Journal Socket. [ OK ] Listening on udev Kernel Socket. [ OK ] Created slice System Slice. Starting Apply Kernel Variables... Starting Setup Virtual Console... Starting dracut cmdline hook... Starting Create list of required st��…ce nodes for the current kernel... [ OK ] Listening on udev Control Socket. [ OK ] Listening on Journal Audit Socket. Starting Journal Service... [ OK ] Reached target Slices. [ OK ] Started Apply Kernel Variables. [ OK ] Started Setup Virtual Console. [ OK 7.106072] audit: type=1130 audit(1498599911.729:2): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=' [ 7.126370] audit: type=1131 audit(1498599911.729:3): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=system' m] Started Create list of required sta��…vice nodes for the current kernel. [ 7.156982] audit: type=1130 audit(1498599911.783:4): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=kmod-s' Starting Create Static Device Nodes in /dev... [ OK ] Started Journal Service. [ 7.199339] audit: type=1130 audit(1498599911.825:5): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=system' [ OK ] Started Create Static Device Nodes in /dev. [ 7.228040] audit: type=1130 audit(1498599911.854:6): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=system' [ 7.702637] random: crng init done [ OK ] Started dracut cmdline hook. [ 8.254886] audit: type=1130 audit(1498599912.881:7): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut' Starting Open-iSCSI... Starting dracut pre-udev hook... [ 8.322323] Loading iSCSI transport class v2.0-870. [ OK ] Started Open-iSCSI. [ 8.335111] audit: type=1130 audit(1498599912.961:8): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=iscsid' [ 8.501809] RPC: Registered named UNIX socket transport module. [ 8.506341] RPC: Registered udp transport module. [ 8.511023] RPC: Registered tcp transport module. [ 8.515689] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 8.594771] dracut-pre-udev[342]: rpcbind: /run/rpcbind/rpcbind.lock: No such file or directory [ 8.899178] dracut-pre-udev[342]: rpc.idmapd: conf_reinit: open ("(null)", O_RDONLY) failed [ 8.911228] dracut-pre-udev[342]: rpc.idmapd: conf_reinit: open ("(null)", O_RDONLY) failed [ OK ] Started dracut pre-udev hook. [ 9.097886] audit: type=1130 audit(1498599913.724:9): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracut' Starting udev Kernel Device Manager... [ OK ] Started udev Kernel Device Manager. [ 9.157117] audit: type=1130 audit(1498599913.783:10): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=syste' Starting dracut pre-trigger hook... [ OK ] Started dracut pre-trigger hook. [ 9.867910] audit: type=1130 audit(1498599914.494:11): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=dracu' Starting udev Coldplug all Devices... Mounting Configuration File System... [ OK ] Mounted Configuration File System. [ OK ] Started udev Coldplug all Devices. [ 10.493178] audit: type=1130 audit(1498599915.119:12): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=syste' [ 10.640274] s5p-secss 10830000.sss: s5p-sss driver registered Starting dracut initqueue hook... Starting Show Plymouth Boot Screen... [ 10.715857] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator [ 10.724074] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator [ 10.741627] audit: type=1130 audit(1498599915.364:13): pid=1 uid=0 auid=4294967295 ses=4294967295 subj=kernel msg='unit=plymo' [ 10.760212] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus not found, using dummy regulator [ 10.774723] ohci-exynos: OHCI EXYNOS driver [ OK ] Started Forward Password Requests to Plymouth Directory Watch. [ OK ] Reache[ 10.789051] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus-boost not found, using dummy regulator d target Paths. [ OK ] Reached target Encrypted Volumes. [ OK ] Reached target System Initialization. [ OK ] Listening on Open-iSCSI iscsiuio Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Ba[ 10.823058] ehci-exynos: EHCI EXYNOS driver [ 10.824756] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator [ 10.831596] exynos-ohci 12120000.usb: USB Host Controller [ 10.832042] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 1 [ 10.832439] exynos-ohci 12120000.usb: irq 71, io mem 0x12120000 [ 10.853998] Synopsys Designware Multimedia Card Interface Driver sic System. [ 10.878840] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 10.889048] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 10.894454] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 10.901654] usb usb1: Product: USB Host Controller [ 10.906399] usb usb1: Manufacturer: Linux 4.11.8-300.fc26.armv7hl ohci_hcd [ 10.913248] usb usb1: SerialNumber: 12120000.usb [ 10.918931] hub 1-0:1.0: USB hub found [ 10.921643] hub 1-0:1.0: 3 ports detected [ 10.956829] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 10.961921] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 10.972965] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 10.981444] exynos-ehci 12110000.usb: EHCI Host Controller [ 10.987355] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 2 [ 10.991360] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.003670] alloc_contig_range: [afc41, afc42) PFNs busy [ 11.007722] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.014070] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.029251] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.039645] exynos-ehci 12110000.usb: irq 71, io mem 0x12110000 [ 11.050644] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00 [ 11.055789] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 11.062047] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.069237] usb usb2: Product: EHCI Host Controller [ 11.074084] usb usb2: Manufacturer: Linux 4.11.8-300.fc26.armv7hl ehci_hcd [ 11.080935] usb usb2: SerialNumber: 12110000.usb [ 11.105617] hub 2-0:1.0: USB hub found [ 11.108052] hub 2-0:1.0: 3 ports detected [ 11.122281] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.128050] s3c-i2c 12c80000.i2c: slave address 0x00 [ 11.132752] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz [ 11.136308] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330 [ 11.136319] dma-pl330 121a0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 11.140871] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330 [ 11.140882] dma-pl330 121b0000.pdma: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 [ 11.142300] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330 [ 11.142311] dma-pl330 10800000.mdma: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32 [ 11.183438] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.189741] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.195122] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.210711] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.212314] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter [ 11.213725] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 11.233187] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 11.233192] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.233212] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.233262] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.240665] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.240720] alloc_contig_range: [afc48, afc49) PFNs busy [ 11.240798] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.240814] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.240859] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.292564] dwmmc_exynos 12220000.mmc: Version ID is 250a [ 11.298160] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 74,64 bit host data width,64 deep fifo [ 11.315085] exynos-hdmi 14530000.hdmi: Failed to get supply 'vdd': -517 [ 11.316817] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.327315] alloc_contig_range: [afc45, afc46) PFNs busy [ 11.332757] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.337833] exynos-rot 11c00000.rotator: The exynos rotator is probed successfully [ 11.339681] exynos-drm-gsc 13e00000.video-scaler: failed to get system register. [ 11.340069] exynos-drm-gsc 13e00000.video-scaler: drm gsc registered successfully. [ 11.340201] exynos-drm-gsc 13e10000.video-scaler: failed to get system register. [ 11.340510] exynos-drm-gsc 13e10000.video-scaler: drm gsc registered successfully. [ 11.341797] exynos-drm-ipp exynos-drm-ipp: drm ipp registered successfully. [ 11.383135] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.388593] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.401373] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 11.407166] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 11.413315] dwmmc_exynos 12220000.mmc: Version ID is 250a [ 11.418689] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 74,64 bit host data width,64 deep fifo [ 11.435503] exynos-hdmi 14530000.hdmi: Failed to get supply 'vdd': -517 [ 11.438618] usb 2-1: new high-speed USB device number 2 using exynos-ehci [ 11.451205] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.461347] alloc_contig_range: [afc45, afc46) PFNs busy [ 11.470779] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.475867] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.479496] s5m-rtc s2mps14-rtc: rtc core: registered s5m-rtc as rtc0 [ 11.487646] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.498989] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode. [ 11.504821] dwmmc_exynos 12220000.mmc: Using internal DMA controller. [ 11.509618] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV [ 11.516769] dwmmc_exynos 12220000.mmc: Version ID is 250a [ 11.522193] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 74,64 bit host data width,64 deep fifo [ 11.525679] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV [ 11.531049] vdd_ldo15: Bringing 3300000uV into 3100000-3100000uV [ 11.541477] vdd_sd: Bringing 3300000uV into 2800000-2800000uV [ 11.567415] usb 2-1: New USB device found, idVendor=05e3, idProduct=0610 [ 11.571115] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) [ 11.582169] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 11.582682] dwmmc_exynos 12220000.mmc: 1 slots initialized [ 11.584725] exynos-tmu 10060000.tmu: More trip points than supported by this TMU. [ 11.584735] exynos-tmu 10060000.tmu: 2 trip points should be configured in polling mode. [ 11.605350] OF: graph: no port node found in /soc/hdmi@14530000 [ 11.609196] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations [ 11.609642] exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops [exynosdrm]) [ 11.610209] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_component_ops [exynosdrm]) [ 11.610690] exynos-drm exynos-drm: bound exynos-drm-vidi (ops vidi_component_ops [exynosdrm]) [ 11.610698] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 11.610702] [drm] No driver support for vblank timestamp query. [ 11.661617] usb 2-1: Product: USB2.0 Hub [ 11.665567] usb 2-1: Manufacturer: GenesysLogic G[ 11.671779] hub 2-1:1.0: USB hub found [ 11.674612] hub 2-1:1.0: 4 ports detected [ 11.747649] Console: switching to colour frame buffer device 240x67 [ 11.820614] exynos-drm exynos-drm: fb0: frame buffer device [ 11.827658] [drm] Initialized exynos 1.0.0 20110530 for exynos-drm on minor 0 [ 11.851995] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.865009] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator [ 11.865082] alloc_contig_range: [afc48, afc49) PFNs busy [ 11.865206] alloc_contig_range: [afc49, afc4a) PFNs busy [ 11.865337] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.865361] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.865408] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.867852] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling [ 11.867997] rtc rtc1: invalid alarm value: 1900-1-2 0:0:0 [ 11.875339] s3c-rtc 101e0000.rtc: rtc core: registered s3c as rtc1 [ 11.877116] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.884686] alloc_contig_range: [afc48, afc49) PFNs busy [ 11.884798] alloc_contig_range: [afc49, afc4a) PFNs busy [ 11.885084] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.885101] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.885154] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.963312] usb_phy_generic usb_phy_generic.1.auto: usb_phy_generic.1.auto supply vcc not found, using dummy regulator [ 11.963599] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.963737] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.963754] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.963802] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.966252] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.966363] alloc_contig_range: [afc4a, afc4b) PFNs busy [ 11.966491] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.966507] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.966638] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.980502] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller [ 11.982673] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 3 [ 11.986615] usb 2-1.3: new full-speed USB device number 3 using exynos-ehci [ 11.987376] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x02010010 [ 11.987454] xhci-hcd xhci-hcd.4.auto: irq 135, io mem 0x12000000 [ 11.987860] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 11.987870] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.987877] usb usb3: Product: xHCI Host Controller [ 11.987885] usb usb3: Manufacturer: Linux 4.11.8-300.fc26.armv7hl xhci-hcd [ 11.987892] usb usb3: SerialNumber: xhci-hcd.4.auto [ 11.988992] hub 3-0:1.0: USB hub found [ 11.989065] hub 3-0:1.0: 1 port detected [ 11.990696] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller [ 11.991013] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.991298] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.991314] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.991360] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.991949] xhci-hcd xhci-hcd.4.auto: new USB bus registered, assigned bus number 4 [ 11.992159] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 11.992406] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 11.992416] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 11.992424] usb usb4: Product: xHCI Host Controller [ 11.992431] usb usb4: Manufacturer: Linux 4.11.8-300.fc26.armv7hl xhci-hcd [ 11.992438] usb usb4: SerialNumber: xhci-hcd.4.auto [ 11.993920] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.994030] alloc_contig_range: [afc51, afc52) PFNs busy [ 11.994160] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.994177] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.994223] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 11.995914] hub 4-0:1.0: USB hub found [ 11.995995] hub 4-0:1.0: 1 port detected [ 11.997943] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 11.998119] alloc_contig_range: [afc51, afc52) PFNs busy [ 11.998161] alloc_contig_range: [afc52, afc53) PFNs busy [ 11.998276] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 11.998292] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 11.998336] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.000903] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller [ 12.000950] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.001058] alloc_contig_range: [afc51, afc52) PFNs busy [ 12.001096] alloc_contig_range: [afc52, afc53) PFNs busy [ 12.001127] alloc_contig_range: [afc53, afc54) PFNs busy [ 12.001366] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.001384] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.001395] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 5 [ 12.001427] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.004064] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.004200] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.004216] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.004257] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.004679] xhci-hcd xhci-hcd.5.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x02010010 [ 12.004748] xhci-hcd xhci-hcd.5.auto: irq 136, io mem 0x12400000 [ 12.005115] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 [ 12.005125] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.005133] usb usb5: Product: xHCI Host Controller [ 12.005141] usb usb5: Manufacturer: Linux 4.11.8-300.fc26.armv7hl xhci-hcd [ 12.005149] usb usb5: SerialNumber: xhci-hcd.5.auto [ 12.006308] hub 5-0:1.0: USB hub found [ 12.006382] hub 5-0:1.0: 1 port detected [ 12.008113] xhci-hcd xhci-hcd.5.auto: xHCI Host Controller [ 12.008451] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.008740] xhci-hcd xhci-hcd.5.auto: new USB bus registered, assigned bus number 6 [ 12.008944] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM. [ 12.008985] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.009002] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.009046] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.009187] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003 [ 12.009197] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 12.009205] usb usb6: Product: xHCI Host Controller [ 12.009213] usb usb6: Manufacturer: Linux 4.11.8-300.fc26.armv7hl xhci-hcd [ 12.009220] usb usb6: SerialNumber: xhci-hcd.5.auto [ 12.011656] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.011761] alloc_contig_range: [afc52, afc53) PFNs busy [ 12.011893] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.011909] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.011952] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.012142] hub 6-0:1.0: USB hub found [ 12.012220] hub 6-0:1.0: 1 port detected [ 12.015575] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.015755] alloc_contig_range: [afc52, afc53) PFNs busy [ 12.016040] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.016057] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.016104] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.071382] usb 2-1.3: New USB device found, idVendor=046d, idProduct=c52b [ 12.071392] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 12.071400] usb 2-1.3: Product: USB Receiver [ 12.071407] usb 2-1.3: Manufacturer: Logitech [ 12.076383] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.077209] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.077227] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.077272] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.080608] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.080794] alloc_contig_range: [afc52, afc53) PFNs busy [ 12.081056] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.081075] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.081121] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.084350] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.084837] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.084855] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.084901] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.127822] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-1212 [ 12.159578] usb 2-1.4: new full-speed USB device number 4 using exynos-ehci [ 12.233213] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.233635] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.233650] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.233697] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.255260] usb 2-1.4: New USB device found, idVendor=046d, idProduct=c52b [ 12.255271] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 12.255279] usb 2-1.4: Product: USB Receiver [ 12.255286] usb 2-1.4: Manufacturer: Logitech [ 12.261591] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.261772] alloc_contig_range: [afc59, afc5a) PFNs busy [ 12.261912] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.261928] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.261973] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.263344] input: Logitech K360 as /devices/platform/soc/12110000.usb/usb2/2-1/2-1.3/2-1.3:1.2/0003:046D:C52B.0003/0003:046D0 [ 12.266137] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.266243] alloc_contig_range: [afc59, afc5a) PFNs busy [ 12.266278] alloc_contig_range: [afc5a, afc5b) PFNs busy [ 12.266392] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.266408] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.266453] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.270938] logitech-hidpp-device 0003:046D:4004.0004: input,hidraw1: USB HID v1.11 Keyboard [Logitech K360] on usb-12110000.1 [ 12.272504] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.272858] alloc_contig_range: [afc59, afc5a) PFNs busy [ 12.272905] alloc_contig_range: [afc5a, afc5b) PFNs busy [ 12.272938] alloc_contig_range: [afc5b, afc5c) PFNs busy [ 12.273073] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.273088] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.273131] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.274388] logitech-djreceiver 0003:046D:C52B.0007: hiddev0,hidraw2: USB HID v1.11 Device [Logitech USB Receiver] on usb-1212 [ 12.380508] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.380956] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.380972] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.381032] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 12.388133] input: Logitech M325 as /devices/platform/soc/12110000.usb/usb2/2-1/2-1.4/2-1.4:1.2/0003:046D:C52B.0007/0003:046D1 [ 12.389710] logitech-hidpp-device 0003:046D:400A.0008: input,hidraw3: USB HID v1.11 Mouse [Logitech M325] on usb-12110000.usb1 [ 12.391278] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 12.391465] alloc_contig_range: [afc59, afc5a) PFNs busy [ 12.391799] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 12.391816] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 12.391862] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 14.262990] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 14.264734] usb_phy_generic usb_phy_generic.2.auto: usb_phy_generic.2.auto supply vcc not found, using dummy regulator [ 14.264921] usb_phy_generic usb_phy_generic.3.auto: usb_phy_generic.3.auto supply vcc not found, using dummy regulator [ 14.323703] alloc_contig_range: [afc59, afc5a) PFNs busy [ 14.340019] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 14.357376] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 14.360376] usb usb3-port1: connect-debounce failed [ 14.391441] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 14.413995] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 14.432100] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 14.450944] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 14.467654] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 15.895324] alloc_contig_range: [afc59, afc5a) PFNs busy [ 15.914967] dma-pl330 3880000.adma: Loaded driver for PL330 DMAC-241330 [ 15.934255] dma-pl330 3880000.adma: DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6 [ 15.955078] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode. [ 15.973101] alloc_contig_range: [afc59, afc5a) PFNs busy [ 15.989498] dwmmc_exynos 12200000.mmc: Using internal DMA controller. [ 16.007364] dwmmc_exynos 12200000.mmc: Version ID is 250a [ 16.023737] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 73,64 bit host data width,64 deep fifo [ 154.826300] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 155.465493] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 156.047171] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 156.628264] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 157.210699] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 157.792716] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 158.375165] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 158.956997] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 159.539328] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 160.121374] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 160.703325] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 161.285883] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 161.867962] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 162.450719] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 163.033505] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 163.614266] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 164.195758] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 164.778469] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 165.360286] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 165.941310] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 166.523524] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 167.104869] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 167.688130] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 168.270306] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 168.852315] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 169.434322] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 170.016732] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 170.602207] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 171.185517] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 171.768552] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 172.350236] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 172.932299] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 173.513380] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 174.095387] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 174.677335] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 175.259292] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 175.839862] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 176.427267] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 177.009588] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 177.592175] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 178.174540] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 178.757416] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 179.340333] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 179.923291] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 180.505974] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 181.088774] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 181.671254] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 182.252978] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 182.834583] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 183.418151] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 184.001124] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 184.584265] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 185.166858] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 185.751389] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 186.332845] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 186.916558] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 187.498291] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 188.083535] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 188.666901] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 189.248788] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 189.832126] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 190.414984] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 190.999165] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 191.583350] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 192.166411] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 192.749409] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 193.331914] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 193.914324] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 194.496689] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 195.078933] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 195.661887] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 196.246104] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 196.828598] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 197.410332] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 197.992727] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 198.575369] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 199.157259] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 199.739920] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 200.322926] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 200.905482] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 201.487460] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 202.069268] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 202.651906] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 203.234337] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts [ 203.815857] dracut-initqueue[493]: Warning: dracut-initqueue timeout - starting timeout scripts On 08/22/2017 01:35 PM, Dennis Gilmore
wrote:
El mar, 15-08-2017 a las 17:25 -0700, Stewart Samuels escribió:Ok. The u-boot issue was my mistake. I was trying to use the /usr/share/uboot/odroid u-boot files instead of the /usr/share/uboot/odroid-xu3 files. Now I am getting output to the serial console and the system begins the boot process as expected. However, it hangs in the kernel seemingly trying to do something with the network. Anyone have any ideas as to what I can try to get past this? Following is my serial console output:try adding cpuide.off=1 to the boot line and see if it boots okay then. Dennis |
_______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
