On Wed, Aug 9, 2017 at 9:17 PM, Stewart Samuels <searider74@xxxxxxxxx> wrote: > Hello Paul, > > I'm not getting any output from the Odroid serial port, even from > u-boot.bin. How can I tell if the issue is from u-boot.bin or after? Also, If you don't get output from u-boot it's a u-boot or a physical config problem > has the initial-setup issue fixed and is it available in the current image > download for the F26 spins? No, we don't respin images once they've gone GA, it will be in F-27 > Stewart > > > On 08/09/2017 12:57 PM, Paul Whalen wrote: >> >> Hi Stewart, >> >> ----- Original Message ----- >>> >>> Hello Andreas, >>> >>> I have been away for awhile as my wife and I relocated from the East >>> Coast of the U.S. to Oregon. Now that we are settling in a bit, I am >>> once again finding some time to work on my Odroid XU4. >>> >>> I hope all is well with you. I see you have been working hard on trying >>> to get the Odroid working with Fedora 26. >> >> I tested the Arndale (Exynos 5250) with F26 GA, there was an issue with >> initial-setup (missing serial console ttySAC2), but otherwise it worked >> quite well. Its not the same board, but the kernel *should* work. >> >>> I have been periodically trying new versions of Fedora since Fedora 24 >>> kernel 4.6.5-300.fc24, including Fedora 26. Something broke after the >>> 4.6.5-300.fc24 release. I cannot tell if the problem lies in the newer >>> u-boot.bin or elsewhere. After the system got broken, I no longer get >>> any output though the serial cable to determine where such problems >>> lie. However, if I install the Hardkernel Ubuntu Mate with 4.9 kernel, >>> everything works fine. I get output through the serial cable and the >>> system boots up beautifully. >>> >>> is it possible for you to email me a zipped copy of the u-boot.bin file >>> you are using to boot? Is it the 4.6.5-300.fc24 version? >>> >>> Thanks. >>> >>> Kind regards, >>> Stewart >>> >>> >>> On 07/25/2017 12:17 AM, arm_ml@xxxxxxxxxxx wrote: >>>> >>>> Hi there, >>>> >>>> I've managed to get Fedora 26 run with kernel 4.6.5-300.fc24.armv7hl >>>> on Odroid-XU4 with Cloudshell 2. The onbord RAID 1 (USB-Attached SCSI >>>> (UAS)) is working with kernel 4.6.5-300.fc24. >>>> >>>> >>>> [root@myodroid ~]# lsusb -d 152d:0561 >>>> Bus 004 Device 003: ID 152d:0561 JMicron Technology Corp. / JMicron >>>> USA Technology Corp. >>>> [root@myodroid ~]# >>>> >>>> Next steps to do: >>>> >>>> - move OS from SD-Card to more faster eMMC-Card. How to do it? >>>> - Kernel update to actual version. I've update Kernel to >>>> 4.11.11-300.fc26 and system boots with 8 CPU (FC24 = 5 CPU), but only >>>> the first part of kernel is booting; then it stops. >>>> - compiling modules to activate the color LCD >>>> >>>> Is there anybody who can help me with the first 2 steps ? >>>> >>>> >>>> Thanks >>>> Andreas >>>> _______________________________________________ >>>> arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx >>>> To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx >>> >>> _______________________________________________ >>> arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx >>> To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx >>> > _______________________________________________ > arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx > To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx _______________________________________________ arm mailing list -- arm@xxxxxxxxxxxxxxxxxxxxxxx To unsubscribe send an email to arm-leave@xxxxxxxxxxxxxxxxxxxxxxx
