A minor bug and is fixed in uboot-tools-2014.10-3.fc21 Peter On Sat, Oct 18, 2014 at 9:04 PM, Adam Goode <adam@xxxxxxxxxxxxx> wrote: > Hopefully I did something wrong, but it's not working at all for me on > the beaglebone black: > > Here is what I get when I try to boot from eMMC: > > U-Boot SPL 2014.10-gc4b8756-dirty (Oct 15 2014 - 08:57:04) > omap_hsmmc_send_cmd: timedout waiting on cmd inhibit to clear > spl: mmc init failed: err - -19 > ### ERROR ### Please RESET the board ### > > > > Here is what I get when I make a new SD card from the latest minimal image: > > > U-Boot 2014.10-gc4b8756-dirty (Oct 15 2014 - 08:57:04) > > Watchdog enabled > I2C: ready > DRAM: 512 MiB > NAND: 0 MiB > MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > *** Error - No Valid Environment Area found > *** Warning - bad CRC, using default environment > > Net: <ethaddr> not set. Validating first E-fuse MAC > cpsw, usb_ether > Hit any key to stop autoboot: 0 > switch to partitions #0, OK > mmc0 is current device > Scanning mmc 0:2... > Failed to mount ext2 filesystem... > ** Unrecognized filesystem type ** > Failed to mount ext2 filesystem... > ** Unrecognized filesystem type ** > Failed to mount ext2 filesystem... > ** Unrecognized filesystem type ** > Failed to mount ext2 filesystem... > ** Unrecognized filesystem type ** > Failed to mount ext2 filesystem... > ** Unrecognized filesystem type ** > Failed to mount ext2 filesystem... > ** Unrecognized filesystem type ** > Failed to mount ext2 filesystem... > ** Unrecognized filesystem type ** > Failed to mount ext2 filesystem... > ** Unrecognized filesystem type ** > Card did not respond to voltage select! > Booting from nand ... > > no devices available > > no devices available > Bad Linux ARM zImage magic! > > > > > When I am in the uboot command processor, I cannot select the internal > eMMC at all: > > U-Boot# mmc dev 1 > Card did not respond to voltage select! > > > > Previously, I was booting with no problems from either eMMC or SD with F21. > > > > Thanks, > > Adam > > > On Wed, Oct 15, 2014 at 6:34 AM, Peter Robinson <pbrobinson@xxxxxxxxx> wrote: >> Hi All, >> >> Just a heads up that the u-boot 2014.10 GA is on it's way to Fedora 21. >> >> https://admin.fedoraproject.org/updates/uboot-tools-2014.10-1.fc21 >> >> This release contains numerous fixes and improvements over the >> currently shipping release including, but by no means limited to: >> * Upstream generic distro support (huge thanks to Dennis Gilmore and >> Steven Warren for their tireless work to get this upstream >> * AllWinner suppport for A10*/A13/A20 devices (huge thanks to Hans for >> this tireless work on this) >> * Numerous other improvements too long to name. >> >> New devices that we now enable in this release, in no particular order, include: >> >> AllWinner: >> A10-OLinuXino-Lime >> A10s-OLinuXino-M >> A13-OLinuXino >> A13-OLinuXinoM >> A20-OLinuXino_MICRO >> Bananapi >> Cubieboard >> Cubieboard2 >> Cubietruck >> Mele_A1000 >> Mele_A1000G >> Mini-X >> Mini-X-1Gb >> >> Tegra: >> jetson-tk1 >> >> i.MX6 >> cm_fx6 (Utilite) >> riotboard >> >> It's not yet in nightly builds but I'm going to request it for the >> next Beta TC compose. >> >> Known issues: >> * Panda is not yet ported to generic distro support >> >> Please test and provide feedback. >> >> Peter >> _______________________________________________ >> arm mailing list >> arm@xxxxxxxxxxxxxxxxxxxxxxx >> https://admin.fedoraproject.org/mailman/listinfo/arm _______________________________________________ arm mailing list arm@xxxxxxxxxxxxxxxxxxxxxxx https://admin.fedoraproject.org/mailman/listinfo/arm
