Dear list,
I have recently got a device with Intel's Poulsbo chipset and Adi 1986
codec attatched.
The Adi 1986 codec along with the Poulsbo chipset could been
recognized by installing the SoundMAX driver under Windows XP.
While switching to Linux, the snd_intel_hda is loaded but the Adi 1986
codec could not been seen and there is no "codec#0" entry under
/proc/asound/card0.
>From what I can see from dmesg, the hda_intel module had complained
about "no codecs found!".
<dmesg.txt>
-- snip --
[ 93.463277] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 93.463286] Do fixup for Poulsbo <6>D0 or newer stepping
[ 93.463439] HDA snoop disabled, try to enable ... OK
[ 93.491624] hda-intel: no codecs found!
-- snip --
I have attached both output of dmesg command the "lspci -nnvvvxxx"
result along with this mail. Any comment would be greatly appreciated.
--
Sincerely,
Jyo
00:1b.0 Audio device [0403]: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller [8086:811b] (rev 06)
Subsystem: Intel Corporation Unknown device [8086:8119]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 17
Region 0: Memory at dff5c000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] Express Unknown type IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed unknown, Width x0, ASPM unknown, Port 0
Link: Latency L0s <64ns, L1 <1us
Link: ASPM L0s Enabled CommClk- ExtSynch-
Link: Speed unknown, Width x0
00: 86 80 1b 81 02 00 10 00 06 00 03 04 08 00 00 00
10: 04 c0 f5 df 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 19 81
30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 80 00 00
50: 01 70 02 48 00 00 00 00 00 00 00 00 00 00 00 00
60: 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 10 00 91 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 0d 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 86 0f 06 00 02 00 00 00
[ 0.000000] Linux version 2.6.24-16-lpia (buildd@molybdenum) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu Apr 10 13:00:24 UTC 2008 (Unofficial)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003fa90000 (usable)
[ 0.000000] BIOS-e820: 000000003fa90000 - 000000003faa0000 (reserved)
[ 0.000000] BIOS-e820: 000000003faa0000 - 000000003faae000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003faae000 - 000000003fae8000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003fae8000 - 000000003fc00000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] Warning only 896MB will be used.
[ 0.000000] Use a HIGHMEM enabled kernel.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 229376) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 229376
[ 0.000000] On node 0 totalpages: 229376
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] Intel MultiProcessor Specification v1.1
[ 0.000000] Virtual Wire compatibility mode.
[ 0.000000] OEM ID: Intel Product ID: Poulsbo APIC at: 0xFEE00000
[ 0.000000] Processor #0 6:12 APIC version 20
[ 0.000000] I/O APIC #1 Version 32 at 0xFEC00000.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Processors: 1
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3fc00000:bf200000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227584
[ 0.000000] Kernel command line: initrd=initrd1.img boot=usb BOOT_IMAGE=linux1 acpi=off
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 1599.950 MHz processor.
[ 60.041752] Console: colour VGA+ 80x25
[ 60.041758] console [tty0] enabled
[ 60.045332] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 60.046297] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 60.073939] Memory: 902236k/917504k available (2044k kernel code, 14744k reserved, 975k data, 268k init, 0k highmem)
[ 60.074059] virtual kernel memory layout:
[ 60.074061] fixmap : 0xfffb3000 - 0xfffff000 ( 304 kB)
[ 60.074063] vmalloc : 0xf8800000 - 0xfffb1000 ( 119 MB)
[ 60.074066] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 60.074068] .init : 0xc03f9000 - 0xc043c000 ( 268 kB)
[ 60.074070] .data : 0xc02ff11b - 0xc03f2d24 ( 975 kB)
[ 60.074072] .text : 0xc0100000 - 0xc02ff11b (2044 kB)
[ 60.074590] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 60.074793] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 60.154927] Calibrating delay using timer specific routine.. 3205.94 BogoMIPS (lpj=6411897)
[ 60.155154] Mount-cache hash table entries: 512
[ 60.155380] CPU: After generic identify, caps: afe9fbff 20100000 00000000 00000000 0040e3bd 00000000 00000001 00000000
[ 60.155393] monitor/mwait feature present.
[ 60.155467] using mwait in idle threads.
[ 60.155543] CPU: L1 I cache: 32K, L1 D cache: 24K
[ 60.155661] CPU: L2 cache: 512K
[ 60.155733] CPU: After all inits, caps: afe9fbff 20100000 00000000 00003940 0040e3bd 00000000 00000001 00000000
[ 60.155747] Compat vDSO mapped to ffffe000.
[ 60.155835] Checking 'hlt' instruction... OK.
[ 60.171369] SMP alternatives: switching to UP code
[ 60.173110] Freeing SMP alternatives: 11k freed
[ 60.173371] Early unpacking initramfs... done
[ 60.391622] CPU0: Intel Genuine Intel(R) CPU @ 1.60GHz stepping 02
[ 60.391860] Total of 1 processors activated (3205.94 BogoMIPS).
[ 60.391995] ExtINT not setup in hardware but reported by MP table
[ 60.392155] ENABLING IO-APIC IRQs
[ 60.392414] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
[ 60.647017] Brought up 1 CPUs
[ 60.647124] CPU0 attaching sched-domain:
[ 60.647129] domain 0: span 01
[ 60.647132] groups: 01
[ 60.647422] net_namespace: 64 bytes
[ 60.647507] Intel Crown Beach board series board detected. Selecting BIOS-method for reboots.
[ 60.647613] Booting paravirtualized kernel on bare hardware
[ 60.648571] Time: 20:34:24 Date: 06/23/08
[ 60.648736] NET: Registered protocol family 16
[ 60.649626] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=0
[ 60.649711] PCI: Using configuration type 1
[ 60.649785] Setting up standard PCI resources
[ 60.657700] ACPI: Interpreter disabled.
[ 60.657780] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 60.657915] pnp: PnP ACPI: disabled
[ 60.658634] PCI: Probing PCI hardware
[ 60.658726] PCI: Probing PCI hardware (bus 00)
[ 60.660527] PCI: Using IRQ router default [8086/8119] at 0000:00:1f.0
[ 60.660622] PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 16
[ 60.660702] PCI->APIC IRQ transform: 0000:00:1a.0[A] -> IRQ 16
[ 60.660782] PCI->APIC IRQ transform: 0000:00:1b.0[A] -> IRQ 16
[ 60.660862] PCI->APIC IRQ transform: 0000:00:1d.0[A] -> IRQ 16
[ 60.660941] PCI->APIC IRQ transform: 0000:00:1d.1[B] -> IRQ 17
[ 60.661021] PCI->APIC IRQ transform: 0000:00:1d.2[C] -> IRQ 18
[ 60.661101] PCI->APIC IRQ transform: 0000:00:1d.7[D] -> IRQ 19
[ 60.661180] PCI->APIC IRQ transform: 0000:00:1e.0[A] -> IRQ 16
[ 60.661266] PCI->APIC IRQ transform: 0000:00:1e.1[B] -> IRQ 17
[ 60.661346] PCI->APIC IRQ transform: 0000:00:1e.2[C] -> IRQ 18
[ 60.671109] NET: Registered protocol family 8
[ 60.671192] NET: Registered protocol family 20
[ 60.672161] NET: Registered protocol family 2
[ 60.674951] Time: tsc clocksource has been installed.
[ 60.707083] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 60.707637] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 60.708919] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 60.709676] TCP: Hash tables configured (established 131072 bind 65536)
[ 60.709762] TCP reno registered
[ 60.719218] checking if image is initramfs... it is
[ 61.144436] Freeing initrd memory: 2981k freed
[ 61.145746] audit: initializing netlink socket (disabled)
[ 61.145847] audit(1214253263.964:1): initialized
[ 61.149533] VFS: Disk quotas dquot_6.5.1
[ 61.149754] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 61.150129] io scheduler noop registered
[ 61.150206] io scheduler anticipatory registered
[ 61.150281] io scheduler deadline registered
[ 61.150463] io scheduler cfq registered (default)
[ 61.150557] Boot video device is 0000:00:02.0
[ 61.231777] Real Time Clock Driver v1.12ac
[ 61.231997] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 61.234002] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 61.234177] iusbc 0000:00:1a.0: ---> iusbc_probe()
[ 61.234207] iusbc 0000:00:1a.0: ---> iusbc_reset()
[ 61.234211] iusbc 0000:00:1a.0: <--- iusbc_reset()
[ 61.234215] iusbc 0000:00:1a.0: ---> iusbc_reinit()
[ 61.234219] iusbc 0000:00:1a.0: <--- iusbc_reinit()
[ 61.234243] PCI: Setting latency timer of device 0000:00:1a.0 to 64
[ 61.234248] iusbc 0000:00:1a.0: Intel Poulsbo USB Client Controller Driver
[ 61.234330] iusbc 0000:00:1a.0: irq 16, pci mem f8800000
[ 61.234406] iusbc 0000:00:1a.0: version: 2.0.0.32L.0009
[ 61.234482] iusbc 0000:00:1a.0: support (max) 8 endpoints
[ 61.234569] iusbc 0000:00:1a.0: <--- iusbc_probe()
[ 61.234804] PNP: No PS/2 controller found. Probing ports directly.
[ 61.254590] i8042.c: Detected active multiplexing controller, rev 1.0.
[ 61.264687] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 61.264768] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 61.264846] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 61.264922] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 61.264999] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 61.265326] mice: PS/2 mouse device common for all mice
[ 61.265541] cpuidle: using governor ladder
[ 61.265615] cpuidle: using governor menu
[ 61.265940] sdhci: Secure Digital Host Controller Interface driver
[ 61.266019] sdhci: Copyright(c) Pierre Ossman
[ 61.266161] sdhci: SDHCI controller found at 0000:00:1e.0 [8086:811c] (rev 6)
[ 61.266264] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 61.266352] mmc0: SDHCI at 0xdff5e800 irq 16 DMA
[ 61.266436] sdhci: SDHCI controller found at 0000:00:1e.1 [8086:811d] (rev 6)
[ 61.266533] PCI: Setting latency timer of device 0000:00:1e.1 to 64
[ 61.269606] mmc1: SDHCI at 0xdff5e400 irq 17 DMA
[ 61.269691] sdhci: SDHCI controller found at 0000:00:1e.2 [8086:811e] (rev 6)
[ 61.269787] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 61.269865] mmc2: SDHCI at 0xdff5e000 irq 18 DMA
[ 61.270105] NET: Registered protocol family 1
[ 61.270229] Using IPI No-Shortcut mode
[ 61.270442] Magic number: 12:878:599
[ 61.270522] hash matches device serial8250
[ 61.270659] hash matches device ptyd3
[ 61.270958] Freeing unused kernel memory: 268k freed
[ 61.302567] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 61.511439] usbcore: registered new interface driver usbfs
[ 61.511596] usbcore: registered new interface driver hub
[ 61.511753] usbcore: registered new device driver usb
[ 61.527478] usbcore: registered new interface driver hiddev
[ 61.527624] usbcore: registered new interface driver usbhid
[ 61.527705] /build/buildd/linux-2.6.24/debian/build/custom-source-lpia/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 61.535822] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 61.535831] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 61.536010] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 61.540041] ehci_hcd 0000:00:1d.7: debug port 1
[ 61.540122] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 61.540138] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xdff5ec00
[ 61.554974] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 61.555387] usb usb1: configuration #1 chosen from 1 choice
[ 61.555556] hub 1-0:1.0: USB hub found
[ 61.555639] hub 1-0:1.0: 8 ports detected
[ 61.666576] USB Universal Host Controller Interface driver v3.0
[ 61.666777] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 61.666784] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 61.666943] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 61.667085] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e480
[ 61.667436] usb usb2: configuration #1 chosen from 1 choice
[ 61.667593] hub 2-0:1.0: USB hub found
[ 61.667676] hub 2-0:1.0: 2 ports detected
[ 61.771125] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 61.771132] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 61.771281] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 61.771406] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e080
[ 61.772874] usb usb3: configuration #1 chosen from 1 choice
[ 61.773034] hub 3-0:1.0: USB hub found
[ 61.773115] hub 3-0:1.0: 2 ports detected
[ 61.875115] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 61.875122] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 61.875270] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 61.875395] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ef00
[ 61.875722] usb usb4: configuration #1 chosen from 1 choice
[ 61.875877] hub 4-0:1.0: USB hub found
[ 61.875958] hub 4-0:1.0: 2 ports detected
[ 61.998385] SCSI subsystem initialized
[ 62.013288] libata version 3.00 loaded.
[ 62.030876] ata_piix 0000:00:1f.1: version 2.12
[ 62.030940] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 62.031046] scsi0 : ata_piix
[ 62.031240] scsi1 : ata_piix
[ 62.031397] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 62.031479] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 62.195315] ata1.00: failed to read native max address (err_mask=0x1)
[ 62.195398] ata1: failed to recover some devices, retrying in 5 secs
[ 62.859000] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 63.037392] usb 2-1: configuration #1 chosen from 1 choice
[ 63.283009] usb 2-2: new full speed USB device using uhci_hcd and address 3
[ 63.461343] usb 2-2: configuration #1 chosen from 1 choice
[ 63.707017] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 63.877333] usb 3-2: configuration #1 chosen from 1 choice
[ 63.880208] hub 3-2:1.0: USB hub found
[ 63.882135] hub 3-2:1.0: 3 ports detected
[ 64.196122] usb 3-2.1: new full speed USB device using uhci_hcd and address 3
[ 64.331311] usb 3-2.1: configuration #1 chosen from 1 choice
[ 64.340523] input: Chicony PFU-68 USB Keyboard as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2.1/3-2.1:1.0/input/input1
[ 64.351114] input,hidraw0: USB HID v1.00 Keyboard [Chicony PFU-68 USB Keyboard] on usb-0000:00:1d.1-2.1
[ 64.556110] usb 3-2.3: new full speed USB device using uhci_hcd and address 4
[ 64.660104] usb 3-2.3: not running at top speed; connect to a high speed hub
[ 64.694306] usb 3-2.3: configuration #1 chosen from 1 choice
[ 67.363421] ata1.00: failed to read native max address (err_mask=0x1)
[ 67.363506] ata1.00: revalidation failed (errno=-13)
[ 67.363582] ata1: failed to recover some devices, retrying in 5 secs
[ 72.531518] ata1.00: failed to read native max address (err_mask=0x1)
[ 72.531599] ata1.00: revalidation failed (errno=-13)
[ 72.531675] ata1.00: disabled
[ 73.215859] Driver 'sd' needs updating - please use bus_type methods
[ 73.222686] usbcore: registered new interface driver libusual
[ 73.231680] Initializing USB Mass Storage driver...
[ 73.236088] scsi2 : SCSI emulation for USB Mass Storage devices
[ 73.236333] usbcore: registered new interface driver usb-storage
[ 73.236416] USB Mass Storage support registered.
[ 73.237251] usb-storage: device found at 4
[ 73.237256] usb-storage: waiting for device to settle before scanning
[ 73.244292] Registering unionfs 1.4
[ 73.244373] unionfs: debugging is not enabled
[ 73.252570] squashfs: version 3.3 (2007/10/31) Phillip Lougher
[ 73.286390] loop: module loaded
[ 73.365265] thermal: Unknown symbol acpi_processor_set_thermal_limit
[ 78.236652] usb-storage: device scan complete
[ 78.239655] scsi 2:0:0:0: Direct-Access Sony Storage Media 0100 PQ: 0 ANSI: 0 CCS
[ 78.249645] sd 2:0:0:0: [sda] 3963904 512-byte hardware sectors (2030 MB)
[ 78.252621] sd 2:0:0:0: [sda] Write Protect is off
[ 78.252702] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 78.252706] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 78.264641] sd 2:0:0:0: [sda] 3963904 512-byte hardware sectors (2030 MB)
[ 78.267616] sd 2:0:0:0: [sda] Write Protect is off
[ 78.267696] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00
[ 78.267700] sd 2:0:0:0: [sda] Assuming drive cache: write through
[ 78.267785] sda: unknown partition table
[ 78.350770] sd 2:0:0:0: [sda] Attached SCSI removable disk
[ 79.178832] EXT2-fs: loop1: couldn't mount because of unsupported optional features (4).
[ 81.444585] kjournald starting. Commit interval 5 seconds
[ 81.444712] EXT3 FS on loop1, internal journal
[ 81.444832] EXT3-fs: recovery complete.
[ 81.444919] EXT3-fs: mounted filesystem with ordered data mode.
[ 92.391760] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 92.922125] poulsbo_smbus 0000:00:1f.0: Found POULSBO SMBUS 0000:00:1f.0 device
[ 92.922240] poulsbo_smbus 0000:00:1f.0: POULSBO SM base = 0x0400
[ 93.463277] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 93.463286] Do fixup for Poulsbo <6>D0 or newer stepping
[ 93.463439] HDA snoop disabled, try to enable ... OK
[ 93.491624] hda-intel: no codecs found!
[ 94.152757] usbcore: registered new interface driver usbserial
[ 94.152898] /build/buildd/linux-2.6.24/debian/build/custom-source-lpia/drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
[ 94.153090] usbcore: registered new interface driver usbserial_generic
[ 94.153173] /build/buildd/linux-2.6.24/debian/build/custom-source-lpia/drivers/usb/serial/usb-serial.c: USB Serial Driver core
[ 94.265838] /build/buildd/linux-2.6.24/debian/build/custom-source-lpia/drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
[ 94.266030] ftdi_sio 2-1:1.0: FTDI USB Serial Device converter detected
[ 94.266150] /build/buildd/linux-2.6.24/debian/build/custom-source-lpia/drivers/usb/serial/ftdi_sio.c: Detected FT232BM
[ 94.266414] usb 2-1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 94.266509] ftdi_sio 2-2:1.0: FTDI USB Serial Device converter detected
[ 94.266622] /build/buildd/linux-2.6.24/debian/build/custom-source-lpia/drivers/usb/serial/ftdi_sio.c: Detected FT232BM
[ 94.266802] usb 2-2: FTDI USB Serial Device converter now attached to ttyUSB1
[ 94.266897] usbcore: registered new interface driver ftdi_sio
[ 94.266976] /build/buildd/linux-2.6.24/debian/build/custom-source-lpia/drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
[ 94.583902] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 96.509619] Warning! dirs delete and imap options to remount are ignored
[ 105.633629] NET: Registered protocol family 10
[ 105.634789] lo: Disabled Privacy Extensions
[ 123.336200] Bluetooth: Core ver 2.11
[ 123.337743] NET: Registered protocol family 31
[ 123.337751] Bluetooth: HCI device and connection manager initialized
[ 123.337759] Bluetooth: HCI socket layer initialized
[ 123.391372] Bluetooth: L2CAP ver 2.9
[ 123.391380] Bluetooth: L2CAP socket layer initialized
[ 123.915356] Bluetooth: RFCOMM socket layer initialized
[ 123.916276] Bluetooth: RFCOMM TTY layer initialized
[ 123.916284] Bluetooth: RFCOMM ver 1.8
-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://sourceforge.net/services/buy/index.php
_______________________________________________
Alsa-user mailing list
Alsa-user@xxxxxxxxxxxxxxxxxxxxx
https://lists.sourceforge.net/lists/listinfo/alsa-user
