Hi,
Everything been working great for quite a while. I use a spdif
connection between my htpc and my receiver. I used dmix as my
alsa:default thus passing analog and digital audio thru this connection.
See the attached asound.conf.
I was playing with xine tonight and at one point it popped up some
message about not gaining access to the audio channel. Don't know if
that was the cause of the problem but now my analog audio pass thru to
the spdif connection is GONE!! The digital audio still works (hdtv and
dvds.) But no analog source material works (analog tv recording.) Even
the annoying system bell is busted. Its like my machine it totally
ignoring the asound.conf.
jboehm@catwomen:~$ /usr/bin/aplay -D default
/usr/share/sounds/alsa/Front_Center.wav
Playing WAVE '/usr/share/sounds/alsa/Front_Center.wav' : Signed 16 bit
Little Endian, Rate 48000 Hz, Mono
But no sound comes out!!!
jboehm@catwomen:~$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: Intel [HDA Intel], device 0: ALC883 Analog [ALC883 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: Intel [HDA Intel], device 1: ALC883 Digital [ALC883 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
jboehm@catwomen:~$ aplay -L
front:CARD=Intel,DEV=0
HDA Intel, ALC883 Analog
Front speakers
surround40:CARD=Intel,DEV=0
HDA Intel, ALC883 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=Intel,DEV=0
HDA Intel, ALC883 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=Intel,DEV=0
HDA Intel, ALC883 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=Intel,DEV=0
HDA Intel, ALC883 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=Intel,DEV=0
HDA Intel, ALC883 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=Intel,DEV=0
HDA Intel, ALC883 Digital
IEC958 (S/PDIF) Digital Audio Output
null
Discard all samples (playback) or generate zero samples (capture)
That -L output doesn't look right to me. It used to have pages of
output. This makes me think something in my alsa configuration got hosed.
Please help ... I'm panicking a little,
Jon
# ~/.asoundrc or /etc/asound.conf
# ALSA configuration file
##### USAGE #####
# Save this file as "~/.asoundrc" (for user-specific sound configuration) or
# "/etc/asound.conf" (for system-wide sound configuration) and specify ALSA
# device names ad described in the next section.
##### DEVICE NAMES #####
# This configuration file defines four devices for use by the user. Those
# devices are "analog", "mixed-analog", "digital", and "mixed-digital". The
# user may also re-define "default" to be identical to one of the above-named
# devices (i.e. to send all sound output to the digital output unless otherwise
# specified). Use the device names as described below:
# - "analog" outputs to the analog output directly and (at least on software
# sound cards) blocks other audio output. After playback completes, "queued"
# sounds are output in sequence.
# - "mixed-analog" mixes audio output from multiple programs into the analog
# output (so you can hear beeps, alerts, and other noises while playing back
# an audio stream).
# - "digital" outputs to the digital output directly. Since most (all?)
# digital outputs expect 48kHz PCM audio, this may not work for some playback
# (i.e. CD's--which are 44.1kHz PCM audio--or 32kHz audio streams from TV
# recordings, etc.).
# - "mixed-digital"
# All other devices created within this file are used only by the configuration
# file itself and should /not/ be used directly. In other words, do not use
# the devices "analog-hw", "dmix-analog", "digital-hw", or "dmix-digital".
##### IMPORTANT #####
# To make this ALSA configuration file work with your sound card, you will need
# to define the appropriate card and device information for the "analog-hw" and
# "digital-hw" devices below. You can find the card and device information
# using "aplay -l".
##### Configuration File #####
# Override the default output used by ALSA. If you do not override the
# default, your default device is identical to the (unmixed) "analog" device
# shown below. If you prefer mixed and/or digital output, uncomment the
# appropriate four lines below (only one slave.pcm line).
#
# Note, also, that as of ALSA 1.0.9, "software" sound cards have been modified
# such that their default "default" device is identical to the "mixed-analog"
# device. Whether using an ALSA version before or after 1.0.9, it does no harm
# and has no affect on performance to redefine the device (even if the
# redefinition does not change anything). Also, by using this ALSA
# configuration file, you once again have access to unmixed analog output using
# the "analog" device.
pcm.!default {
type plug
## Uncomment the following to use (unmixed) "analog" by default
# slave.pcm "analog-hw"
## Uncomment the following to use "mixed-analog" by default
# slave.pcm "dmix-analog"
## Uncomment the following to use (unmixed) "digital" by default
# slave.pcm "digital-hw"
## Uncomment the following to use "mixed-digital" by default
slave.pcm "dmix-digital"
}
pcm.rc {
type plug
slave.pcm "rate-changer"
}
pcm.rate-changer {
type plug
slave {
# period_time 0
# period_size 1024
# buffer_size 4096
rate 48000
pcm "spdif"
}
}
# Control device (mixer, etc.) for the card
ctl.!default {
type hw
card 0
}
# Alias for (converted) analog output on the card
# - This is identical to the device named "default"--which always exists and
# refers to hw:0,0 (unless overridden)
# - Therefore, we can specify "hw:0,0", "default", or "analog" to access analog
# output on the card
# - Note that as of ALSA 1.0.9, "software" sound card definitions redefine
# "default" to do mixing, meaning this device is different from "default" and
# allows playback while blocking other sound sources (until playback
# completes).
pcm.analog {
type plug
slave.pcm "analog-hw"
}
# Control device (mixer, etc.) for the card
ctl.analog {
type hw
card 0
}
# Alias for (converted) mixed analog output on the card
# - This will accept audio input--regardless of rate--and convert to the rate
# required for the dmix plugin (in this case 48000Hz)
# - Note that as of ALSA 1.0.9, "software" sound card definitions redefine
# "default" to do mixing, meaning this device is identical to "default" for
# "software" sound cards.
pcm.mixed-analog {
type plug
slave.pcm "dmix-analog"
}
# Control device (mixer, etc.) for the card
ctl.mixed-analog {
type hw
card 0
}
# Alias for (converted) digital (S/PDIF) output on the card
# - This will accept audio input--regardless of rate--and convert to the rate
# required for the S/PDIF hardware (in this case 48000Hz)
pcm.digital {
type plug
slave.pcm "digital-hw"
}
# Control device (mixer, etc.) for the card
ctl.digital {
type hw
card 0
}
# Alias for mixed (converted) digital (S/PDIF) output on the card
# - This will accept audio input--regardless of rate--and convert to the rate
# required for the S/PDIF hardware (in this case 48000Hz)
pcm.mixed-digital {
type plug
slave.pcm "dmix-digital"
}
# Control device (mixer, etc.) for the card
ctl.mixed-digital {
type hw
card 0
}
# The following devices are not useful by themselves. They require specific
# rates, channels, and formats. Therefore, you probably do not want to use
# them directly. Instead use of of the devices defined above.
# Alias for analog output on the card
# Do not use this directly--it requires specific rate, channels, and format
pcm.analog-hw {
type hw
card 0
# The default value for device is 0, so no need to specify
# - Uncomment one of the below or create a new "device N" line as appropriate
# for your sound card or
# device 1
# device 4
}
# Control device (mixer, etc.) for the card
ctl.analog-hw {
type hw
card 0
}
# Alias for digital (S/PDIF) output on the card
# Do not use this directly--it requires specific rate, channels, and format
pcm.digital-hw {
type hw
card 0
device 1
# - Comment out "device 1" above and uncomment one of the below or create a
# new "device N" line as appropriate for your sound card or
# device 2
# device 4
}
# Control device (mixer, etc.) for the card
ctl.digital-hw {
type hw
card 0
}
# Direct software mixing plugin for analog output on the card
# Do not use this directly--it requires specific rate, channels, and format
pcm.dmix-analog {
type dmix
ipc_key 1234
slave {
pcm "analog-hw"
period_time 0
period_size 1024
buffer_size 4096
rate 48000
}
}
# Control device (mixer, etc.) for the card
ctl.dmix-analog {
type hw
card 0
}
# Direct software mixing plugin for digital (S/PDIF) output on the card
# Do not use this directly--it requires specific rate, channels, and format
pcm.dmix-digital {
type dmix
ipc_key 1235
slave {
pcm "digital-hw"
period_time 0
period_size 1024
buffer_size 4096
rate 48000
}
}
# Control device (mixer, etc.) for the card
ctl.dmix-digital {
type hw
card 0
}
-------------------------------------------------------------------------
This SF.net email is sponsored by: Splunk Inc.
Still grepping through log files to find problems? Stop.
Now Search log events and configuration files using AJAX and a browser.
Download your FREE copy of Splunk now >> http://get.splunk.com/
_______________________________________________
Alsa-user mailing list
Alsa-user@xxxxxxxxxxxxxxxxxxxxx
https://lists.sourceforge.net/lists/listinfo/alsa-user
