Re: VDR jumps to old position after ff/rew

[Stefan Schallenberg <infos@xxxxxxxxx>]

Hi Klaus,

I am using OpenSUSE 12.3 with standard kernel 3.7.10. - do you think I 
need to switch to Liplianin or other driver packages forcing me to 
recompile parts of the kernel?

On the same system VDR 1.6 did not show the problem, does VDR 2.x handle 
DVB device (dvbsddevice plugin) different than 1.6?

Stefan

Am 27.08.2013 22:05, schrieb Klaus Schmidinger:
> On 27.08.2013 20:47, Stefan Schallenberg wrote:
> > Hi all,
> >
> > Thanks for your ideas.
> >
> > I am using an old (SD but not HD) FF PCI card and non-HD recordings. 
> > So neither of the situations you described applies as far as I 
> > understan.
>
> Are you sure you are using the latest driver and firmware for that card?
> Old versions might not return the actual STC value.
>
> Klaus
>
>
> > Some more background:
> > A lot of my recordings are done with VDR 1.6, but the symptom occurs 
> > both with old and new recordings. I currently dont have a HD device 
> > attached. I am running in a XEN-virualized Environment with PCI 
> > passthrough.
> >
> > vVdr:~ # lspci -v
> > 00:00.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
> >          Subsystem: Technotrend Systemtechnik GmbH 
> > Siemens/Technotrend/Hauppauge DVB card rev1.3 or rev1.5
> >          Flags: bus master, medium devsel, latency 64, IRQ 16
> >          Memory at f7fff000 (32-bit, non-prefetchable) [size=512]
> >          Kernel driver in use: av7110
> >
> > 00:01.0 Multimedia controller: Philips Semiconductors SAA7146 (rev 01)
> >          Subsystem: Technotrend Systemtechnik GmbH 
> > Technotrend/Hauppauge DVB card rev2.1
> >          Flags: bus master, medium devsel, latency 64, IRQ 18
> >          Memory at f7ffe000 (32-bit, non-prefetchable) [size=512]
> >          Kernel driver in use: av7110
> >
> >
> > Stefan
> >
> > Am 27.08.2013 20:36, schrieb Tony Houghton:
> > > This problem still exists with vdr-sxfe and HD recordings.
> > >
> > > On Tue, 27 Aug 2013 11:28:24 -0700
> > > VDR User <user.vdr@xxxxxxxxx> wrote:
> > >
> > > > I believe that's a problem with the video decoder. I had the same 
> > > > problem
> > > > using vdpau with vdr-xine long ago but it was quickly fixed. When I 
> > > > started
> > > > testing vdr-softhddevice, the problem re-appeared. You can enable 
> > > > "CONFIG
> > > > += -DH264_EOS_TRICKSPEED" in vdr-softhddevice/Makefile and it 
> > > > should work,
> > > > assuming you're using vdr-softhddevice & are using a recent git of it.
> > > >
> > > >
> > > > On Tue, Aug 27, 2013 at 9:51 AM, Stefan Schallenberg 
> > > > <infos@xxxxxxxxx>wrote:
> > > >
> > > > > Hi all,
> > > > >
> > > > > I detected a strange behaviour in VDR 2.0.2:
> > > > > When I replay a recording and press right for fast forwarding and 
> > > > > after
> > > > > some time press "up" to continue playing at this position vdr 
> > > > > jumps back to
> > > > > the position where I started the forwarding. I would expect it to 
> > > > > continue
> > > > > replay at the position where I forwarded to.
> > > > >
> > > > > Is this a known bug or do I have to press other keys or is there a 
> > > > > setting
> > > > > to change it?
>
> _______________________________________________
> vdr mailing list
> vdr@xxxxxxxxxxx
> http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr


_______________________________________________
vdr mailing list
vdr@xxxxxxxxxxx
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr