As I mentioned in my previous email, I'm using diseqc.conf to drive my motorized dish.
I noticed that sometimes VDR generates false channe updates, when the dish is moving. The problem is, channel switches immediately, but it takes seconds for the dish to move. Often there is several seconds time when VDR thinks it's already on the new channel, but old satellite is still tuned.
I googled and I noticed something about this in actuator plugin README:
"vdr assumes that, as soon as a channel has been switched to, the new source (satellite) is valid, even if the dish is moving, so the autoupdate function will assign new/updated channels to the wrong satellite. The plugin's workaround is to disable autoupdate while the dish is moving and restore the previous setting only when it has reached the target satellite. It's possible that the plugin will fail to restore the value of this setting. If you see that channels aren't updating anymore check this setting (main menu->configuration->dbv->update channels, note that while the dish is moving this setting is always "no", so check and modify it only when the actuator is idle). "
RotorNG does not have such hack, so it still suffers from this problem. Also as I said, I use VDR "as is" without rotor-ng, and have this problem.
I made the following patch to sections.c, this is for vdr 1.7.27 but I guess it's similar in newer VDRs as well..
If source has been changed, it forces a 10 second delay. This means that epg data and channel updates are disabled during that time, but it shouldn't matter.
10 seconds might not be quite enough to get to the new position with a slow motor, but it is enough to make the frontend loose lock on the previous satellite..
Here's also example from syslog:
Feb 8 15:17:23 yavdr vdr: [16352] switching to channel 990
Feb 8 15:17:23 yavdr vdr: [16420] New source 0x5300ff7e, 10sec wait forced in section loop
Feb 8 15:17:29 yavdr vdr: [16419] frontend 1/0 lost lock on channel 990, tp 112322
Feb 8 15:17:30 yavdr vdr: [16419] frontend 1/0 regained lock on channel 990, tp 112322
Here you can see how it takes full 6 seconds before frontend reports lost lock, after channel switch.. Channel is really switched at 15:17:30 when it regains lock. If any section data would be received between 15:17:23 - 15:17:29, it would be registered on the wrong satellite.
------------------------------
The patch:
*** vdr-alt/sections.c 2007-10-14 15:52:07.000000000 +0300
--- vdr/sections.c 2013-02-08 14:50:30.524186976 +0200
***************
*** 164,169 ****
--- 164,171 ----
void cSectionHandler::Action(void)
{
+ int PrevSource=shp->channel.Source();
+
SetPriority(19);
while (Running()) {
***************
*** 183,188 ****
--- 185,196 ----
if (poll(pfd, NumFilters, 1000) > 0) {
bool DeviceHasLock = device->HasLock();
+ if (PrevSource!=shp->channel.Source()) {
+ PrevSource=shp->channel.Source();
+ DeviceHasLock = false;
+ dsyslog("New source 0x%x, 10sec wait forced in section loop\n",PrevSource);
+ cCondWait::SleepMs(10000);
+ }
if (!DeviceHasLock)
cCondWait::SleepMs(100);
for (int i = 0; i < NumFilters; i++) {
--
Teemu Suikki
http://www.z-power.fi/
_______________________________________________ vdr mailing list vdr@xxxxxxxxxxx http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr
