Petri Helin wrote: > Klaus Schmidinger wrote: >> Petri Helin wrote: >>> Klaus Schmidinger wrote: >>>> Petri Helin wrote: >>>>> Klaus Schmidinger wrote: >>>>>> Looks like the CAM is recognized all right. >>>>>> >>>>>> Please enable the lines >>>>>> >>>>>> static bool DumpTPDUDataTransfer = false; >>>>>> static bool DebugProtocol = false; >>>>>> static bool DumpPolls = false; >>>>>> static bool DumpDateTime = false; >>>>>> >>>>>> in ci.c by changing them to 'true' and compile/run VDR again, >>>>>> redirecting >>>>>> stderr into a file, as in >>>>>> >>>>>> ./vdr 2> ci.txt >>>>>> >>>>>> Then send me the resulting output after trying to switch to an >>>>>> encrypted >>>>>> channel. >>>>>> >>>>> Attached. >>>> Everything looks fine, the CaPmt is sent to the CAM and the >>>> communication with the CAM is stable. It should work. >>>> >>>> Can you please do the same with VDR 1.4 and send me the result of >>>> that, too? >>> ... >>> Here you are. >> >> Ah, now I see the difference: >> >> 3: ==> Ca Pmt >> 4 --> 00 01 A0 2F 01 90 02 00 03 9F 80 32 26 03 01 35 01 00 07 >> 01 09 04 0B 00 E0 68 02 02 06 00 00 04 02 AE 00 00 04 02 AF 00 00 04 >> 02 AC 00 00 04 02 AD 00 00 >> >> Slot 1: ==> Ca Pmt (3) 3 3 >> 1: --> 00 01 A0 10 01 90 02 00 03 9F 80 32 07 03 00 00 01 00 01 03 >> >> For some reason VDR 1.4.4 sends the CA descriptors in the CaPmt, while >> VDR 1.5.0 >> doesn't. >> >> Please post the channels.conf entry for the channel you are trying to >> tune to. >> >> Also, just to make sure: are you using plain vanilla VDR 1.5.0 or are >> there >> any patches involved? >> >> Klaus >> >> _______________________________________________ >> vdr mailing list >> vdr@xxxxxxxxxxx >> http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr >> > > Here are the channels that VDR 1.5.0 cannot tune to: > > > Canal+ > Mix;Telenor:266000:C0M128:C:6900:518:686=nor,687=fin,684=sve,685=dan:581:1:309:0:9:0 > > Canal+ Film > 1;Telenor:266000:C0M128:C:6900:512:650=sve,651=dan,652=nor,653=fin;654=eng:576:1:301:0:9:0 > > Canal+ Film > 2;Telenor:266000:C0M128:C:6900:515:682=nor,683=fin,680=sve,681=dan;679=eng:579:1:308:0:9:0 > > Canal+ Film > 3;Telenor:314000:C0M128:C:6900:518:664=sve,665=dan,666=nor,667=fin;668=eng:577:1:3307:0:19:0 > > Canal+ HD;Telenor:330000:C0M256:C:6900:512:640;641=eng:580:1:3306:0:22:0 > Canal+ Sport 1;Telenor:266000:C0M128:C:6900:514:670=fin:577:1:305:0:9:0 > Canal+ Sport > 2;Telenor:314000:C0M128:C:6900:519:672=sve,673=dan,674=nor,675=fin:578:1:3308:0:19:0 Ah, just as I thought. Please set the CA parameter of these channels to 0 (FTA) and tune to them again. VDR should automatically insert the correct CA values then. >From the HISTORY: - Ca values in the range 0...F in channels.conf can still be used to assign a channel to a particular device, but this will no longer work with encrypted channels because without valid CA ids VDR can't decide which CAM slot to use. However, since VDR now automatically determines which CAM can decrypt which channel, setting fixed channel/device relations should no longer be necessary. Klaus
