Hello
Because Kernel 2.4 is not very well supported any more with DVB(-T),
i thought it would be a good idea to update from debian.woody to sarge
and then to the 2.6.x kernel.
debain apt makes that so easy...:
I added the "sarge" resources to sources.list
did
#apt-get update
#aptiude upgrade
# #130MB downloads later(the box is more than only a VDR):
#lilo(*)
#reboot
I see the "DVB-RAM-test" on the TV but
VDR
does not find an mpeg decoder anymore!
What am i missing?
Any hints why VDR is not fiinding the DVB cards any more?
The kernel is unchanged 2.4.28.
I just wondered why "deffs" was installed by the upgrade...
In VDR and DVB i made "make clean" and makevdr resp. make ; make install
but it does not really help.
Rebooted again.
Result see below.
i tried to go back to 1.3.18 but that failed because of
the new timer format
00:03:21 vdr[2346]: loading /video0/sources.conf
00:03:21 vdr[2346]: loading /video0/diseqc.conf
00:03:21 vdr[2346]: loading /video0/channels.conf
00:03:21 vdr[2346]: loading /video0/timers.conf
00:03:21 vdr[2346]: ERROR: error in /video0/timers.conf, line 109
00:03:21 vdr[2346]: saved setup to /video0/setup.conf
00:03:21 vdr[2346]: stopping plugin: femon
00:03:21 vdr[2346]: stopping plugin: undelete
00:03:21 vdr[2346]: undelete: cPluginUndelete::~cPluginUndelete
00:03:21 vdr[2346]: stopping plugin: osdteletext
00:03:21 vdr[2346]: max. latency time 0 seconds
00:03:21 vdr[2346]: exiting
Ok, using backup an vdr 1.3.18
00:13:15 vdr[3860]: timer 130 (13 1100-1132 'Mega') set to event Mon 30.05.2005 11:00-11:30 (VPS: 30.05 11:00) 'nano'
./dvb-ttpci-budget.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
./dvb-ttpci-budget-ci.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
./dvb-ttpci-budget-av.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
./skystar2.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
Using /lib/modules/2.4.29/misc/dvb-core.o
insmod: a module named dvb-core already exists
dmesg does not contain not result...
1.3.18 is now not working anymore too ;-(
00:19:08 vdr[2114]: starting plugin: femon
00:19:08 vdr[2114]: loading /video0/themes/sttng-default.theme
00:19:08 lircd 0.7.0[2051]: accepted new client on /dev/lircd
00:19:08 vdr[2119]: LIRC remote control thread started (pid=2119, tid=49156)
00:19:08 vdr[2114]: remote control LIRC - keys known
00:19:23 vdr[2114]: setting watchdog timer to 60 seconds
00:19:23 vdr[2114]: ERROR: no OSD provider available - using dummy OSD!
I did not "aptitude dist-upgrade" as this would require further 190MB
of down load (i' try to get a CD...)
----------------------------------------------------------------------
((*)honestly i did not "lilo" so reboot ends in "LI" and have to
boot Knoppy and did the lilo there in chroot ..debian apt is not that perfect ;-)
lilo now aways says:
msi:~# lilo
Warning: '/proc/partitions' does not match '/dev' directory structure.
Name change: '/dev/ide/host0/bus1/target0/lun0/disc' -> '/dev/hdc'
)
but i don't have devfs installed.
Maybe just a new feature of sarg lilo. But the box i sboot)
dmesg
...
LVM version 1.0.8(17/11/2003) module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,4), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 00:0a.0, irq: 10, latency: 64, mmio: 0xcfcfe000
bttv0: detected: AVermedia DVB-T 771 [card=121], PCI subsystem ID is 1461:0771
bttv0: using: AVerMedia AVerTV DVB-T 771 [card=121,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=0090000f [init]
i2c-dev.o: Registered 'bt878 #0 [hw]' as minor 0
i2c-core.o: adapter bt878 #0 [hw] registered as adapter 0.
bttv0: using tuner=-1
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
i2c-core.o: driver i2c TV tuner driver registered.
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
bt878(0): Bt878 (rev 17) at 00:0a.1, irq: 10, latency: 64, memory: 0xcfcff000
btaudio: driver version 0.7 loaded [digital+analog]
saa7146: register extension 'dvb'.
saa7146_core: found saa7146 @ mem e1960e00 (revision 1, irq 5) (0x13c2,0x0003).
DVB: registering new adapter (Technotrend/Hauppauge PCI rev2.1).
Technotrend/Hauppauge PCI rev2.1 adapter 0 has MAC addr = 00:d0:5c:20:30:9b
DVB: AV7111(0) - firm f0240009, rtsl b0250018, vid 71010068, app 8000261d
DVB: AV7111(0) - firmware supports CI link layer interface
av7110(0): adac type set to 0
saa7146_fops: saa7146 (0): registered device video1 [v4l2]
av7110: found av7110-0.
saa7146_core: found saa7146 @ mem e1a0ac00 (revision 1, irq 5) (0x13c2,0x0003).
DVB: registering new adapter (Technotrend/Hauppauge PCI rev2.1).
Technotrend/Hauppauge PCI rev2.1 adapter 1 has MAC addr = 00:d0:5c:20:78:9e
DVB: AV7111(1) - firm f0240009, rtsl b0250018, vid 71010068, app 8000261d
DVB: AV7111(1) - firmware supports CI link layer interface
av7110(1): Crystal audio DAC detected
saa7146_fops: saa7146 (1): registered device video2 [v4l2]
av7110: found av7110-1.
saa7146_core: found saa7146 @ mem e1ab4a00 (revision 1, irq 5) (0x13c2,0x0000).
DVB: registering new adapter (Siemens/Technotrend/Hauppauge PCI rev1.3).
Siemens/Technotrend/Hauppauge PCI rev1.3 adapter 2 has MAC addr = 00:d0:5c:02:16:cc
DVB: AV7111(2) - firm f0240009, rtsl b0250018, vid 71010068, app 8000261d
DVB: AV7111(2) - firmware supports CI link layer interface
av7110(2): Crystal audio DAC detected
saa7146_fops: saa7146 (2): registered device video3 [v4l2]
av7110: found av7110-2.
ehci_hcd 00:03.3: Silicon Integrated Systems [SiS] USB 2.0 Controller
ehci_hcd 00:03.3: irq 5, pci mem e1b64000
usb.c: new USB bus registered, assigned bus number 4
PCI: cache line size of 64 is not supported by device 00:03.3
ehci_hcd 00:03.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb.c: USB disconnect on device 00:03.2-1 address 2
Intel 810 + AC97 Audio, version 1.01, 00:46:52 Jan 23 2005
i810: SiS 7012 found at IO 0xd800 and 0xdc00, MEM 0x0000 and 0x0000, IRQ 10
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
ac97_codec: AC97 codec, id: CMI97 (CMedia)
AC97 codec does not have proper volume support.
i810_audio: only 48Khz playback available.
i810_audio: AC'97 codec 0, new EID value = 0x05c6
i810_audio: AC'97 codec 0, DAC map configured, total channels = 6
hub.c: new USB device 00:03.2-1, assigned address 3
input: USB HID v1.10 Keyboard [Twinhan Tech Remote Control] on usb1:3.0
input: USB HID v1.10 Mouse [Twinhan Tech Remote Control] on usb1:3.1
eth0: Media Link On 100mbps full-duplex
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4095 buckets, 32760 max) - 288 bytes per conntrack
lirc_dev: IR Remote Control driver registered, at major 61
lirc_serial: auto-detected active low receiver
lirc_dev: lirc_register_plugin:sample_rate: 0
bt878(0): unloading
bt878_mem: 0xe18fd000.
i2c-core.o: driver unregistered: i2c TV tuner driver
bttv0: unloading
i2c-core.o: adapter unregistered: bt878 #0 [hw]
saa7146: unregister extension 'dvb'.
bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 00:0a.0, irq: 10, latency: 64, mmio: 0xcfcfe000
bttv0: detected: AVermedia DVB-T 771 [card=121], PCI subsystem ID is 1461:0771
bttv0: using: AVerMedia AVerTV DVB-T 771 [card=121,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=0090000f [init]
i2c-dev.o: Registered 'bt878 #0 [hw]' as minor 0
i2c-core.o: adapter bt878 #0 [hw] registered as adapter 0.
bttv0: using tuner=-1
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 . ok
i2c-core.o: driver i2c TV tuner driver registered.
bt878: AUDIO driver version 0.0.0 loaded
bt878: Bt878 AUDIO function found (0).
bt878(0): Bt878 (rev 17) at 00:0a.1, irq: 10, latency: 64, memory: 0xcfcff000
DVB: registering new adapter (Ave).
DVB: registering frontend 0:0 (DVB-T Zarlink MT352 demodulator driver)...
23:34:32 logger[2068]: /root/video/VDR/runvdr restarting VDR
23:34:42 kernel: bt878(0): unloading
23:34:42 kernel: bt878_mem: 0xe18fd000.
23:34:42 kernel: i2c-core.o: driver unregistered: i2c TV tuner driver
23:34:42 kernel: bttv0: unloading
23:34:42 kernel: i2c-core.o: adapter unregistered: bt878 #0 [hw]
23:34:42 kernel: saa7146: unregister extension 'dvb'.
23:34:48 kernel: bttv: driver version 0.9.15 loaded
23:34:48 kernel: bttv: using 8 buffers with 2080k (520 pages) each for capture
23:34:48 kernel: bttv: Bt8xx card found (0).
23:34:48 kernel: bttv0: Bt878 (rev 17) at 00:0a.0, irq: 10, latency: 64, mmio: 0xcfcfe000
23:34:48 kernel: bttv0: detected: AVermedia DVB-T 771 [card=121], PCI subsystem ID is 1461:0771
23:34:48 kernel: bttv0: using: AVerMedia AVerTV DVB-T 771 [card=121,autodetected]
23:34:48 kernel: bttv0: gpio: en=00000000, out=00000000 in=0090000f [init]
23:34:48 kernel: i2c-dev.o: Registered 'bt878 #0 [hw]' as minor 0
23:34:48 kernel: i2c-core.o: adapter bt878 #0 [hw] registered as adapter 0.
23:34:48 kernel: bttv0: using tuner=-1
23:34:48 kernel: bttv0: registered device video0
23:34:48 kernel: bttv0: registered device vbi0
23:34:48 kernel: bttv0: PLL: 28636363 => 35468950 . ok
23:34:48 kernel: i2c-core.o: driver i2c TV tuner driver registered.
23:34:48 kernel: bt878: AUDIO driver version 0.0.0 loaded
23:34:48 kernel: bt878: Bt878 AUDIO function found (0).
23:34:48 kernel: bt878(0): Bt878 (rev 17) at 00:0a.1, irq: 10, latency: 64, memory: 0xcfcff000
23:34:48 kernel: DVB: registering new adapter (Ave).
23:34:48 kernel: DVB: registering frontend 0:0 (DVB-T Zarlink MT352 demodulator driver)...
23:34:49 vdr[2104]: VDR version 1.3.24 started
23:34:49 vdr[2104]: loading plugin: ./PLUGINS/lib/libvdr-osdteletext.so.1.3.24
23:34:49 vdr[2104]: loading plugin: ./PLUGINS/lib/libvdr-undelete.so.1.3.24
23:34:49 vdr[2104]: Undelete: cPluginUndelete::cPluginUndelete
23:34:49 vdr[2104]: loading plugin: ./PLUGINS/lib/libvdr-femon.so.1.3.24
23:34:49 vdr[2104]: loading /video0/setup.conf
23:34:49 vdr[2104]: ERROR: unknown config parameter: AC3dynrng = 1
23:34:49 vdr[2104]: ERROR: unknown config parameter: AC3overDVB = 0
... lot of unknow parameter
23:34:49 vdr[2104]: ERROR: unknown config parameter: Streaming = 4 1
23:34:49 vdr[2104]: ERROR: unknown config parameter: StreamTTL = 2
23:34:49 vdr[2104]: ERROR: unknown config parameter: Symbol = 1
23:34:49 vdr[2104]: undelete: Setupparameter verbose=1
23:34:49 vdr[2104]: undelete: Setupparameter visible=1
23:34:49 vdr[2104]: loading /video0/sources.conf
23:34:49 vdr[2104]: loading /video0/diseqc.conf
23:34:49 vdr[2104]: loading /video0/channels.conf
23:34:49 vdr[2104]: loading /video0/timers.conf
23:34:49 vdr[2104]: loading /video0/commands.conf
23:34:49 vdr[2104]: loading /video0/reccmds.conf
23:34:49 vdr[2104]: loading /video0/svdrphosts.conf
23:34:49 vdr[2104]: loading /video0/ca.conf
23:34:49 vdr[2104]: loading /video0/remote.conf
23:34:49 vdr[2104]: loading /video0/keymacros.conf
23:34:49 vdr[2104]: reading EPG data from /video0/epg.data
23:34:49 vdr[2104]: probing /dev/dvb/adapter0/frontend0
23:34:49 vdr[2107]: tuner on device 1 thread started (pid=2107, tid=16386)
23:34:49 vdr[2104]: probing /dev/dvb/adapter1/frontend0
23:34:49 vdr[2104]: found 1 video device
23:34:49 vdr[2104]: initializing plugin: osdteletext (0.5): Displays teletext on the OSD
23:34:49 vdr[2104]: initializing plugin: undelete (0.0.2): undelete for recordings
23:34:49 vdr[2104]: initializing plugin: femon (0.8.9): DVB Signal Information Monitor (OSD)
23:34:49 vdr[2104]: setting primary device to 1
23:34:49 vdr[2104]: device 1 has no MPEG decoder
23:34:49 vdr[2104]: SVDRP listening on port 2001
23:34:49 vdr[2108]: Section handler thread started (pid=2108, tid=32771)
23:34:49 vdr[2104]: loading /video0/themes/sttng-default.theme
23:34:49 vdr[2104]: starting plugin: osdteletext
23:34:49 vdr[2104]: starting plugin: undelete
23:34:49 vdr[2104]: undelete: cPluginUndelete::Start undeleteconfigfile=undelete.conf
23:34:49 vdr[2104]: undelete: INFO: config file not found: [/video0/plugins/]undelete.conf
23:34:49 vdr[2104]: undelete: Start
23:34:50 vdr[2104]: starting plugin: femon
23:34:50 vdr[2104]: loading /video0/themes/sttng-default.theme
23:34:50 lircd 0.7.0[2051]: accepted new client on /dev/lircd
23:34:50 vdr[2109]: LIRC remote control thread started (pid=2109, tid=49156)
23:34:50 vdr[2104]: remote control LIRC - keys known
23:34:55 vdr[2104]: setting watchdog timer to 60 seconds
23:34:55 vdr[2104]: ERROR: no OSD provider available - using dummy OSD!
23:34:55 vdr[2104]: timer 49 (80 0100-0200 'Domian') set to event Wed 25.05.2005 01:00-02:00 (VPS: 25.05 01:00) 'Domian'
23:34:55 vdr[2104]: timer 68 (15 2300-2345 'Prisma-Magazin') set to event Tue 24.05.2005 23:00-23:45 (VPS: 24.05 23:00) 'Prisma'
23:34:55 vdr[2104]: no free DVB device to record channel 15!
Rainer---<=====> Vertraulich
//
//
<=====>--------------ocholl, Kiel, Germany ------------
