On Wed, Mar 17, 2021 at 01:08:09PM +0100, Oleksij Rempel wrote:
> This should make maintaining work easier.
>
> Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
> ---
Applied, thanks
Sascha
> arch/arm/dts/imx6dl-alti6p.dts | 119 +----
> arch/arm/dts/imx6dl-lanmcu.dts | 463 +-----------------
> arch/arm/dts/imx6dl-plybas.dts | 185 +------
> arch/arm/dts/imx6dl-plym2m.dts | 176 +------
> arch/arm/dts/imx6dl-prtmvt.dts | 163 +------
> arch/arm/dts/imx6dl-prtrvt.dts | 184 +------
> arch/arm/dts/imx6dl-prtvt7.dts | 473 +-----------------
> arch/arm/dts/imx6dl-victgo.dts | 144 +-----
> arch/arm/dts/imx6dl-vicut1.dts | 50 +-
> arch/arm/dts/imx6q-prti6q.dts | 533 +-------------------
> arch/arm/dts/imx6q-prtwd2.dts | 187 +------
> arch/arm/dts/imx6q-vicut1.dts | 65 +--
> arch/arm/dts/imx6qdl-prti6q-emmc.dtsi | 49 ++
> arch/arm/dts/imx6qdl-prti6q-nor.dtsi | 5 +
> arch/arm/dts/imx6qdl-prti6q.dtsi | 216 ---------
> arch/arm/dts/imx6qdl-vicut1.dtsi | 234 ---------
> arch/arm/dts/imx6qp-prtwd3.dts | 675 +-------------------------
> arch/arm/dts/imx6qp-vicutp.dts | 51 +-
> arch/arm/dts/imx6ul-prti6g.dts | 109 ++---
> arch/arm/dts/imx6ul-prti6g.dtsi | 330 -------------
> 20 files changed, 133 insertions(+), 4278 deletions(-)
> create mode 100644 arch/arm/dts/imx6qdl-prti6q-emmc.dtsi
> delete mode 100644 arch/arm/dts/imx6qdl-prti6q.dtsi
> delete mode 100644 arch/arm/dts/imx6qdl-vicut1.dtsi
> delete mode 100644 arch/arm/dts/imx6ul-prti6g.dtsi
>
> diff --git a/arch/arm/dts/imx6dl-alti6p.dts b/arch/arm/dts/imx6dl-alti6p.dts
> index 8d53100bea..04a6368f93 100644
> --- a/arch/arm/dts/imx6dl-alti6p.dts
> +++ b/arch/arm/dts/imx6dl-alti6p.dts
> @@ -1,118 +1,5 @@
> -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> -/*
> - * Copyright (c) 2016 Protonic Holland
> - */
> -
> +// SPDX-License-Identifier: GPL-2.0-or-later
> /dts-v1/;
> -#include <arm/imx6dl.dtsi>
> -#include "imx6qdl-prti6q.dtsi"
> -
> -/ {
> - model = "Altesco I6P Board";
> - compatible = "alt,alti6p", "fsl,imx6dl";
> -
> - memory@10000000 {
> - device_type = "memory";
> - reg = <0x10000000 0x40000000>;
> - };
> -};
> -
> -&hdmi {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hdmi>;
> - ddc-i2c-bus = <&i2c1>;
> - status = "okay";
> -};
> -
> -/* DDC */
> -&i2c1 {
> - clock-frequency = <100000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c1>;
> - status = "okay";
> -};
> -
> -&i2c3 {
> - rtc: pcf8563@51 {
> - compatible = "nxp,pcf8563";
> - reg = <0x51>;
> - };
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rmii";
> - phy-reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
> - clocks = <&clks IMX6QDL_CLK_ENET>,
> - <&clks IMX6QDL_CLK_ENET>;
> - clock-names = "ipg", "ahb";
> - status = "okay";
> -};
> -
> -&i2c2 {
> - clock-frequency = <50000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c2>;
> - status = "okay";
> -};
> -
> -&i2c4 {
> - clock-frequency = <50000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c4>;
> - status = "okay";
> -};
> -
> -&iomuxc {
> - pinctrl_usbotg: usbotggrp {
> - fsl,pins = <
> - MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
> - MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> - /* power enable, high active */
> - MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
> - >;
> - };
> -
> - pinctrl_hdmi: hdmigrp {
> - fsl,pins = <
> - /* NOTE: DDC is done via I2C2, so DON'T configure DDC pins for HDMI! */
> - MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> - >;
> - };
> -
> - pinctrl_i2c2: i2c2grp {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> - MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> - >;
> - };
> -
> - pinctrl_i2c4: i2c4grp {
> - fsl,pins = <
> - MX6QDL_PAD_NANDF_CS3__I2C4_SDA 0x4001f8b1
> - MX6QDL_PAD_NANDF_WP_B__I2C4_SCL 0x4001f8b1
> - >;
> - };
> -
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP4 */
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> - MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> - MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
>
> - MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
> - /* Phy reset */
> - MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
> - /* nINTRP */
> - MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
> - >;
> - };
> -};
> +#include <arm/imx6dl-alti6p.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6dl-lanmcu.dts b/arch/arm/dts/imx6dl-lanmcu.dts
> index d50e6afe7e..1a1fbad326 100644
> --- a/arch/arm/dts/imx6dl-lanmcu.dts
> +++ b/arch/arm/dts/imx6dl-lanmcu.dts
> @@ -1,464 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2019 Protonic Holland
> - */
> -
> /dts-v1/;
> -#include <arm/imx6dl.dtsi>
> -#include <dt-bindings/gpio/gpio.h>
> -
> -/ {
> - model = "LANMCU";
> - compatible = "lan,lanmcu", "fsl,imx6dl";
> -
> - chosen {
> - stdout-path = &uart4;
> -
> - environment-emmc {
> - compatible = "barebox,environment";
> - device-path = &usdhc3, "partname:barebox-environment";
> - };
> - };
> -
> - memory {
> - reg = <0x10000000 0x10000000>;
> - };
> -
> - reg_usb_otg_vbus: otg-vbus-regulator {
> - compatible = "regulator-fixed";
> - regulator-name = "regulator-OTG-VBUS";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - gpio = <&gpio3 22 0>;
> - enable-active-high;
> - };
> -
> - usdhc2_pwrseq: usdhc2_pwrseq {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_wlan_npd>;
> - compatible = "mmc-pwrseq-simple";
> - reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
> - };
> -
> - display: display0 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ipu1_disp>;
> - compatible = "fsl,imx-parallel-display";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - interface-pix-fmt = "bgr666";
> - status = "okay";
> -
> - port@0 {
> - reg = <0>;
> -
> - display_in: endpoint {
> - remote-endpoint = <&ipu1_di0_disp0>;
> - };
> - };
> -
> - port@1 {
> - reg = <1>;
> -
> - display_out: endpoint {
> - remote-endpoint = <&panel_in>;
> - };
> - };
> - };
> -
> - panel {
> - compatible = "edt,etm0700g0bdh6";
> - backlight = <&backlight_lcd>;
> -
> - port {
> - panel_in: endpoint {
> - remote-endpoint = <&display_out>;
> - };
> - };
> - };
> -
> - backlight_lcd: backlight_lcd {
> - compatible = "pwm-backlight";
> - pwms = <&pwm1 0 5000000 0>;
> - brightness-levels = <0 5 7 9 12 15 20 27 35 47 62 81 107 142 188 248
> - 328 433 573 757 1000>;
> - default-brightness-level = <20>;
> - status = "okay";
> - };
> -
> - leds: leds {
> - compatible = "gpio-leds";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_leds>;
> -
> - debug0 {
> - label = "debug0";
> - gpios = <&gpio1 8 0>;
> - linux,default-trigger = "heartbeat";
> - };
> - };
> -
> - clk50m_phy: phy_clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <50000000>;
> - };
> -};
> -
> -&iomuxc {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hog>;
> -
> - prti6q {
> - pinctrl_hog: hoggrp {
> - fsl,pins = <
> - /* HW revision detect */
> - MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
> - MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
> - MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
> - MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
> - MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 /* REV_ID4 */
> - >;
> - };
> -
> - pinctrl_usbotg: usbotggrp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> - /* power enable, high active */
> - MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
> - >;
> - };
> -
> - pinctrl_ipu1_disp: ipudisp1grp {
> - fsl,pins = <
> - /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
> - MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
> - MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
> - MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
> - MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
> - MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
> - MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
> - MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
> - MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
> - MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
> - MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
> - MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
> - MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
> - MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
> - MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
> - MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
> - MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
> - MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
> - MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
> - MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
> - MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
> - MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
> - MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
> - >;
> - };
> -
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP4 */
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> - MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> - MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
> -
> - MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
> - /* Phy reset */
> - MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
> - /* nINTRP */
> - MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
> - >;
> - };
> -
> - pinctrl_pwm1: pwm1grp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
> - >;
> - };
> -
> - pinctrl_leds: ledsgrp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> - >;
> - };
> -
> - pinctrl_wlan_npd: wlan_npd {
> - fsl,pins = <
> - /* WL_REG_ON */
> - MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
> - >;
> - };
> -
> - pinctrl_uart2: uart2grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
> - MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
> - MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x130b1
> - >;
> - };
> -
> - pinctrl_uart3: uart3grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
> - MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
> - MX6QDL_PAD_EIM_D30__UART3_CTS_B 0x130b1
> - >;
> - };
> -
> - pinctrl_uart4: uart4grp {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> - MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> - >;
> - };
> -
> - pinctrl_i2c1: i2c1grp {
> - fsl,pins = <
> - MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
> - MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
> - >;
> - };
> -
> - pinctrl_i2c3: i2c3grp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> - MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> - >;
> - };
> -
> - pinctrl_usdhc1: usdhc1grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
> - MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
> - MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
> - MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
> - MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
> - MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
> - MX6QDL_PAD_GPIO_1__SD1_CD_B 0x1b0b0
> - >;
> - };
> -
> - pinctrl_usdhc2: usdhc2grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> - MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> - MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> - MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> - MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> - MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> - >;
> - };
> -
> - pinctrl_usdhc3: usdhc3grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
> - MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
> - MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
> - MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
> - MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
> - MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
> - MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
> - MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
> - MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
> - MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
> - >;
> - };
> -
> - pinctrl_can1: can1grp {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
> - MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
> - >;
> - };
> -
> - pinctrl_can2: can2grp {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
> - MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
> - >;
> - };
> -
> - pinctrl_ts_edt: ts1grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
> - >;
> - };
> - };
> -};
> -
> -&ipu1_di0_disp0 {
> - remote-endpoint = <&display_in>;
> -};
> -
> -&pwm1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_pwm1>;
> - status = "okay";
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rmii";
> - clocks = <&clks IMX6QDL_CLK_ENET>,
> - <&clks IMX6QDL_CLK_ENET>,
> - <&clk50m_phy>;
> - clock-names = "ipg", "ahb", "ptp";
> - status = "okay";
> -
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - /* Microchip KSZ8081RNA PHY */
> - rgmii_phy: ethernet-phy@0 {
> - reg = <0>;
> - interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
> - reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
> - reset-assert-us = <10000>;
> - reset-deassert-us = <300>;
> - };
> - };
> -};
> -
> -&uart2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart2>;
> - linux,rs485-enabled-at-boot-time;
> - uart-has-rtscts;
> - status = "okay";
> -};
> -
> -&uart3 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart3>;
> - linux,rs485-enabled-at-boot-time;
> - uart-has-rtscts;
> - status = "okay";
> -};
> -
> -&uart4 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart4>;
> - status = "okay";
> -};
> -
> -&usbotg {
> - vbus-supply = <®_usb_otg_vbus>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usbotg>;
> - phy_type = "utmi";
> - dr_mode = "host";
> - status = "okay";
> -};
> -
> -&i2c1 {
> - clock-frequency = <100000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c1>;
> - status = "okay";
> -};
> -
> -&i2c3 {
> - clock-frequency = <100000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c3>;
> - status = "okay";
> -
> - rtc: pcf8563@51 {
> - compatible = "nxp,pcf8563";
> - reg = <0x51>;
> - };
> -
> - touchscreen: edt_ft5406@38 {
> - compatible = "edt,edt-ft5406";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ts_edt>;
> - reg = <0x38>;
> - interrupt-parent = <&gpio3>;
> - interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
> -
> - touchscreen-size-x = <1792>;
> - touchscreen-size-y = <1024>;
> -
> - touchscreen-fuzz-x = <0>;
> - touchscreen-fuzz-y = <0>;
> -
> - /* Touch screen calibration */
> - threshold = <50>;
> - gain = <5>;
> - offset = <10>;
> - };
> -};
> -
> -&usdhc1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc1>;
> - cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> - status = "okay";
> -};
> -
> -&usdhc2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc2>;
> - no-1-8-v;
> - non-removable;
> - mmc-pwrseq = <&usdhc2_pwrseq>;
> - pm-ignore-notify;
> - status = "okay";
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - brcmf: bcrmf@1 {
> - reg = <1>;
> - compatible = "brcm,bcm4329-fmac";
> - };
> -};
> -
> -&usdhc3 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc3>;
> - bus-width = <8>;
> - non-removable;
> - status = "okay";
> -
> - partitions {
> - /*
> - * Map a partition at the last 64k of the area available for
> - * the second stage bootloader.
> - */
> - compatible = "fixed-partitions";
> - #size-cells = <1>;
> - #address-cells = <1>;
> -
> - partition@100000 {
> - label = "barebox-environment";
> - reg = <0x100000 0x100000>;
> - };
> -
> - partition@200000 {
> - label = "state";
> - reg = <0x200000 0x100000>;
> - };
> - };
> -};
> -
> -&can1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_can1>;
> - status = "okay";
> -};
>
> -&can2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_can2>;
> - status = "okay";
> -};
> +#include <arm/imx6dl-lanmcu.dts>
> +#include "imx6qdl-prti6q-emmc.dtsi"
> diff --git a/arch/arm/dts/imx6dl-plybas.dts b/arch/arm/dts/imx6dl-plybas.dts
> index de0ba05e13..b0e1595a41 100644
> --- a/arch/arm/dts/imx6dl-plybas.dts
> +++ b/arch/arm/dts/imx6dl-plybas.dts
> @@ -1,186 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> /dts-v1/;
> -#include <arm/imx6dl.dtsi>
> -#include "imx6qdl-vicut1.dtsi"
> -
> -/ {
> - model = "Plymovent BAS board";
> - compatible = "ply,plybas", "fsl,imx6dl";
> -
> - memory {
> - reg = <0x10000000 0x10000000>;
> - };
> -
> - backlight_lcd {
> - status = "disabled";
> - };
> -
> - gpio_keys {
> - compatible = "gpio-keys";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - autorepeat;
> - button@20 {
> - label = "START";
> - linux,code = <31>;
> - gpios = <&gpio5 8 1>;
> - };
> - button@21 {
> - label = "CLEAN";
> - linux,code = <46>;
> - gpios = <&gpio5 9 1>;
> - };
> - };
> -
> - leds: leds {
> - compatible = "gpio-leds";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_leds>;
> -
> - debug0 {
> - label = "debug0";
> - gpios = <&gpio1 8 0>;
> - };
> -
> - debug1 {
> - label = "debug1";
> - gpios = <&gpio1 9 0>;
> - };
> -
> - light_tower1 {
> - label = "light_tower1";
> - gpios = <&gpio4 22 0>;
> - linux,default-trigger = "heartbeat";
> - };
> -
> - light_tower2 {
> - label = "light_tower2";
> - gpios = <&gpio4 23 0>;
> - };
> -
> - light_tower3 {
> - label = "light_tower3";
> - gpios = <&gpio4 24 0>;
> - };
> -
> - light_tower4 {
> - label = "light_tower4";
> - gpios = <&gpio4 25 0>;
> - };
> - };
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rmii";
> - phy-reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> - clocks = <&clks IMX6QDL_CLK_ENET>,
> - <&clks IMX6QDL_CLK_ENET>;
> - clock-names = "ipg", "ahb";
> - status = "okay";
> -};
> -
> -&uart2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart2>;
> - fsl,uart-has-rtscts;
> - linux,rs485-enabled-at-boot-time;
> - rs485-rts-delay = <0 20>;
> - status = "okay";
> -};
> -
> -&iomuxc {
> - pinctrl_hog: hoggrp {
> - fsl,pins = <
> - /* CAN1_SR + CAN2_SR GPIO outputs */
> - MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
> - MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
> -
> - MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0 /* YACO_nIRQ */
> - MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0 /* YACO_BOOT0 */
> - MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 /* YACO_nRESET */
> -
> - MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x13070 /* BUZZER */
> - MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x13070 /* ANA_OUT_SD */
> - MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0 /* ANA_OUT_ERR */
> -
> - MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x13070 /* RELAY1 */
> - MX6QDL_PAD_DISP0_DAT12__GPIO5_IO06 0x13070 /* RELAY2 */
> -
> - MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0 /* IN1 */
> - MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0 /* IN2 */
> - MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x1b0b0 /* IN3 */
> - MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x1b0b0 /* IN4 */
> - MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x1b0b0 /* IN5 */
> - MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x1b0b0 /* IN6 */
> - MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x1b0b0 /* IN7 */
> - MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x1b0b0 /* IN8 */
> - MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16 0x1b0b0 /* IN9 */
> - MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17 0x1b0b0 /* IN10 */
> - MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0 /* IN11 */
> - MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 /* IN12 */
> -
> - MX6QDL_PAD_DI0_PIN3__GPIO4_IO19 0x1a0b0 /* HMI */
> -
> - /* HW revision detect */
> - MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
> - MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
> - MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
> - MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
> - MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 /* REV_ID4 */
> - >;
> - };
> -
> - pinctrl_leds: ledsgrp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 /* DEBUG0 */
> - MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 /* DEBUG1 */
> -
> - MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070 /* LED1 (lighttower) */
> - MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070 /* LED2 (lighttower) */
> - MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070 /* LED3 (lighttower) */
> - MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070 /* LED4 (lighttower) */
> - >;
> - };
> -
> - /* RS485 UART */
> - pinctrl_uart2: uart2grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
> - MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
> - MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1
> - >;
> - };
> -
> - pinctrl_pwm1: pwm1grp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
> - >;
> - };
> -
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP4 */
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> - MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> - MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
>
> - MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
> - /* Phy reset */
> - MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
> - /* nINTRP */
> - MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
> - >;
> - };
> -};
> +#include <arm/imx6dl-plybas.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6dl-plym2m.dts b/arch/arm/dts/imx6dl-plym2m.dts
> index e944a14dce..bf29fc1bce 100644
> --- a/arch/arm/dts/imx6dl-plym2m.dts
> +++ b/arch/arm/dts/imx6dl-plym2m.dts
> @@ -1,177 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> /dts-v1/;
> -#include <arm/imx6dl.dtsi>
> -#include "imx6qdl-prti6q.dtsi"
> -#include "imx6qdl-prti6q-nor.dtsi"
> -
> -/ {
> - model = "Plymovent M2M board";
> - compatible = "ply,plym2m", "fsl,imx6dl";
> -
> - memory {
> - reg = <0x10000000 0x10000000>;
> - };
> -
> - leds: leds {
> - compatible = "gpio-leds";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_leds>;
> -
> - debug0 {
> - label = "debug0";
> - gpios = <&gpio1 8 0>;
> - linux,default-trigger = "heartbeat";
> - };
> - };
> -
> - clk50m_phy: phy_clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <50000000>;
> - };
> -};
> -
> -&ecspi1 {
> - cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi1>;
> - status = "okay";
> -
> - flash@0 {
> - compatible = "jedec,spi-nor";
> - reg = <0>;
> - spi-max-frequency = <20000000>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - };
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rmii";
> - clocks = <&clks IMX6QDL_CLK_ENET>,
> - <&clks IMX6QDL_CLK_ENET>,
> - <&clk50m_phy>;
> - clock-names = "ipg", "ahb", "ptp";
> - status = "okay";
> -
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - /* Microchip KSZ8081RNA PHY */
> - rgmii_phy: ethernet-phy@0 {
> - reg = <0>;
> - interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
> - reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
> - reset-assert-us = <10000>;
> - reset-deassert-us = <300>;
> - };
> - };
> -};
>
> -&iomuxc {
> - pinctrl_hog: hoggrp {
> - fsl,pins = <
> - /* CAN1_SR GPIO output */
> - MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
> -
> - MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 /* CAN1_TERM */
> - MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 /* TSC_BUSY */
> -
> - /* HW revision detect */
> - MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
> - MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
> - MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
> - MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
> - MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 /* REV_ID4 */
> - >;
> - };
> -
> - pinctrl_ecspi1: ecspi1grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> - MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> - MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> - /* CS */
> - MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
> - >;
> - };
> -
> - pinctrl_usbotg: usbotggrp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> - /* power enable, high active */
> - MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
> - >;
> - };
> -
> - pinctrl_ipu1_disp: ipudisp1grp {
> - fsl,pins = <
> - /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
> - MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30
> - MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30
> - MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30
> - MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30
> - MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30
> - MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30
> - MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30
> - MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30
> - MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30
> - MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30
> - MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30
> - MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30
> - MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30
> - MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30
> - MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30
> - MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30
> - MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30
> - MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30
> - MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30
> - MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30
> - MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30
> - MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30
> - >;
> - };
> -
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP4 */
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> - MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> - MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
> -
> - MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
> - /* Phy reset */
> - MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
> - /* nINTRP */
> - MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
> - >;
> - };
> -
> - pinctrl_pwm1: pwm1grp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
> - >;
> - };
> -
> - pinctrl_backlight_m2m: backlightm2mgrp {
> - };
> -
> - pinctrl_leds: ledsgrp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> - >;
> - };
> -};
> +#include <arm/imx6dl-plym2m.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6dl-prtmvt.dts b/arch/arm/dts/imx6dl-prtmvt.dts
> index 05fce7178f..64e2f90110 100644
> --- a/arch/arm/dts/imx6dl-prtmvt.dts
> +++ b/arch/arm/dts/imx6dl-prtmvt.dts
> @@ -1,164 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> /dts-v1/;
> -#include <arm/imx6dl.dtsi>
> -#include "imx6qdl-vicut1.dtsi"
> -
> -/ {
> - model = "Protonic MVT board";
> - compatible = "prt,prtmvt", "fsl,imx6dl";
> -
> - memory {
> - reg = <0x10000000 0x20000000>;
> - };
> -
> - gpio_keys {
> - compatible = "gpio-keys";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - autorepeat;
> -
> - button@20 {
> - label = "GPIO Key F1";
> - linux,code = <59>;
> - gpios = <&pca_gpio 0 GPIO_ACTIVE_LOW>;
> - };
> - button@21 {
> - label = "GPIO Key F2";
> - linux,code = <60>;
> - gpios = <&pca_gpio 1 GPIO_ACTIVE_LOW>;
> - };
> - button@22 {
> - label = "GPIO Key F3";
> - linux,code = <61>;
> - gpios = <&pca_gpio 2 GPIO_ACTIVE_LOW>;
> - };
> - button@23 {
> - label = "GPIO Key F4";
> - linux,code = <62>;
> - gpios = <&pca_gpio 3 GPIO_ACTIVE_LOW>;
> - };
> - button@24 {
> - label = "GPIO Key F5";
> - linux,code = <63>;
> - gpios = <&pca_gpio 4 GPIO_ACTIVE_LOW>;
> - };
> -
> - // Center
> - button@25 {
> - label = "GPIO Key CYCLE";
> - linux,code = <154>;
> - gpios = <&pca_gpio 5 GPIO_ACTIVE_LOW>;
> - };
> - button@26 {
> - label = "GPIO Key ESC";
> - linux,code = <1>;
> - gpios = <&pca_gpio 6 GPIO_ACTIVE_LOW>;
> - };
> - button@27 {
> - label = "GPIO Key UP";
> - linux,code = <103>;
> - gpios = <&pca_gpio 7 GPIO_ACTIVE_LOW>;
> - };
> - button@28 {
> - label = "GPIO Key DOWN";
> - linux,code = <108>;
> - gpios = <&pca_gpio 8 GPIO_ACTIVE_LOW>;
> - };
> - button@29 {
> - label = "GPIO Key OK";
> - linux,code = <0x160>;
> - gpios = <&pca_gpio 9 GPIO_ACTIVE_LOW>;
> - };
> -
> - button@2a {
> - label = "GPIO Key F6";
> - linux,code = <64>;
> - gpios = <&pca_gpio 10 GPIO_ACTIVE_LOW>;
> - };
> - button@2b {
> - label = "GPIO Key F7";
> - linux,code = <65>;
> - gpios = <&pca_gpio 11 GPIO_ACTIVE_LOW>;
> - };
> - button@2c {
> - label = "GPIO Key F8";
> - linux,code = <66>;
> - gpios = <&pca_gpio 12 GPIO_ACTIVE_LOW>;
> - };
> - button@2d {
> - label = "GPIO Key F9";
> - linux,code = <67>;
> - gpios = <&pca_gpio 13 GPIO_ACTIVE_LOW>;
> - };
> - button@2e {
> - label = "GPIO Key F10";
> - linux,code = <68>;
> - gpios = <&pca_gpio 14 GPIO_ACTIVE_LOW>;
> - };
> - };
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rmii";
> - phy-reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> - clocks = <&clks IMX6QDL_CLK_ENET>,
> - <&clks IMX6QDL_CLK_ENET>;
> - clock-names = "ipg", "ahb";
> - status = "okay";
> -};
> -
> -&pwm2 {
> - status = "disabled";
> -};
> -
> -&pcie {
> - status = "disabled";
> -};
> -
> -&i2c1 {
> - pca_gpio: gpio@74 {
> - #gpio-cells = <2>;
> - compatible = "nxp,pca9539";
> - reg = <0x74>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_pca9539>;
> - interrupt-parent = <&gpio4>;
> - interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
> - gpio-controller;
> - };
> -};
> -
> -&iomuxc {
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP4 */
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> - MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> - MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
> -
> - MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
> - /* Phy reset */
> - MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
> - /* nINTRP */
> - MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
> - >;
> - };
>
> - pinctrl_pca9539: pca9539 {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0
> - >;
> - };
> -};
> +#include <arm/imx6dl-prtmvt.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6dl-prtrvt.dts b/arch/arm/dts/imx6dl-prtrvt.dts
> index c403ba3ea7..e0d9261d27 100644
> --- a/arch/arm/dts/imx6dl-prtrvt.dts
> +++ b/arch/arm/dts/imx6dl-prtrvt.dts
> @@ -1,183 +1,5 @@
> -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> +// SPDX-License-Identifier: GPL-2.0-or-later
> /dts-v1/;
> -#include <arm/imx6dl.dtsi>
> -#include "imx6qdl-prti6q.dtsi"
> -#include "imx6qdl-prti6q-nor.dtsi"
> -#include <dt-bindings/leds/common.h>
> -
> -/ {
> - model = "Protonic RVT board";
> - compatible = "prt,prtrvt", "fsl,imx6dl";
> -
> - memory@10000000 {
> - device_type = "memory";
> - reg = <0x10000000 0x10000000>;
> - };
> -
> - leds {
> - compatible = "gpio-leds";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_leds>;
> -
> - led-debug0 {
> - function = LED_FUNCTION_STATUS;
> - gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "heartbeat";
> - };
> - };
> -};
> -
> -&can1 {
> - pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
> -};
> -
> -&ecspi1 {
> - cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi1>;
> - status = "okay";
> -
> - flash@0 {
> - compatible = "jedec,spi-nor";
> - reg = <0>;
> - spi-max-frequency = <20000000>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - };
> -};
> -
> -&ecspi3 {
> - cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi3>;
> - status = "okay";
> -
> - nfc@0 {
> - compatible = "ti,trf7970a";
> - reg = <0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_nfc>;
> - spi-max-frequency = <2000000>;
> - interrupts-extended = <&gpio5 14 IRQ_TYPE_LEVEL_LOW>;
> - ti,enable-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>,
> - <&gpio5 11 GPIO_ACTIVE_LOW>;
> - vin-supply = <®_3v3>;
> - vin-voltage-override = <3100000>;
> - autosuspend-delay = <30000>;
> - irq-status-read-quirk;
> - en2-rf-quirk;
> - t5t-rmb-extra-byte-quirk;
> - status = "okay";
> - };
> -};
> -
> -&i2c3 {
> - adc@49 {
> - compatible = "ti,ads1015";
> - reg = <0x49>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - /* nc */
> - channel@4 {
> - reg = <4>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
>
> - /* nc */
> - channel@5 {
> - reg = <5>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> -
> - /* can1_l */
> - channel@6 {
> - reg = <6>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> -
> - /* can1_h */
> - channel@7 {
> - reg = <7>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> - };
> -
> - rtc@51 {
> - compatible = "nxp,pcf8563";
> - reg = <0x51>;
> - };
> -};
> -
> -&pcie {
> - status = "okay";
> -};
> -
> -&usbh1 {
> - status = "disabled";
> -};
> -
> -&vpu {
> - status = "disabled";
> -};
> -
> -&iomuxc {
> - pinctrl_can1phy: can1phy {
> - fsl,pins = <
> - /* CAN1_SR */
> - MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
> - /* CAN1_TERM */
> - MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
> - >;
> - };
> -
> - pinctrl_ecspi1: ecspi1grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> - MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> - MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> - /* CS */
> - MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
> - >;
> - };
> -
> - pinctrl_ecspi3: ecspi3grp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
> - MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
> - MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
> - MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
> - >;
> - };
> -
> - pinctrl_leds: ledsgrp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> - >;
> - };
> -
> - pinctrl_nfc: nfcgrp {
> - fsl,pins = <
> - /* NFC_ASK_OOK */
> - MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x100b1
> - /* NFC_PWR_EN */
> - MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x100b1
> - /* NFC_EN2 */
> - MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x100b1
> - /* NFC_EN */
> - MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
> - /* NFC_MOD */
> - MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13 0x100b1
> - /* NFC_IRQ */
> - MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14 0x100b1
> - >;
> - };
> -};
> +#include <arm/imx6dl-prtrvt.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6dl-prtvt7.dts b/arch/arm/dts/imx6dl-prtvt7.dts
> index 27daa3e15f..b1fd13bdd7 100644
> --- a/arch/arm/dts/imx6dl-prtvt7.dts
> +++ b/arch/arm/dts/imx6dl-prtvt7.dts
> @@ -1,472 +1,5 @@
> -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> -/*
> - * Copyright (c) 2016 Protonic Holland
> - */
> -
> +// SPDX-License-Identifier: GPL-2.0-or-later
> /dts-v1/;
> -#include <arm/imx6dl.dtsi>
> -#include "imx6qdl-prti6q.dtsi"
> -#include <dt-bindings/input/input.h>
> -#include <dt-bindings/leds/common.h>
> -#include <dt-bindings/sound/fsl-imx-audmux.h>
> -
> -/ {
> - model = "Protonic VT7";
> - compatible = "prt,prtvt7", "fsl,imx6dl";
> -
> - memory@10000000 {
> - device_type = "memory";
> - reg = <0x10000000 0x20000000>;
> - };
> -
> - backlight_lcd: backlight-lcd {
> - compatible = "pwm-backlight";
> - pwms = <&pwm1 0 500000 0>;
> - brightness-levels = <0 20 81 248 1000>;
> - default-brightness-level = <20>;
> - num-interpolated-steps = <21>;
> - power-supply = <®_12v_bl>;
> - enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> - };
> -
> - display {
> - compatible = "fsl,imx-parallel-display";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ipu1_disp>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - interface-pix-fmt = "rgb24";
> - status = "okay";
> -
> - port@0 {
> - reg = <0>;
> -
> - display_in: endpoint {
> - remote-endpoint = <&ipu1_di0_disp0>;
> - };
> - };
> -
> - port@1 {
> - reg = <1>;
> -
> - display_out: endpoint {
> - remote-endpoint = <&panel_in>;
> - };
> - };
> - };
> -
> - keys {
> - compatible = "gpio-keys";
> - autorepeat;
> -
> - esc {
> - label = "GPIO Key ESC";
> - linux,code = <KEY_ESC>;
> - gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
> - };
> -
> - up {
> - label = "GPIO Key UP";
> - linux,code = <KEY_UP>;
> - gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
> - };
> -
> - down {
> - label = "GPIO Key DOWN";
> - linux,code = <KEY_DOWN>;
> - gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
> - };
> -
> - enter {
> - label = "GPIO Key Enter";
> - linux,code = <KEY_ENTER>;
> - gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
> - };
> -
> - cycle {
> - label = "GPIO Key CYCLE";
> - linux,code = <KEY_CYCLEWINDOWS>;
> - gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
> - };
> -
> - f1 {
> - label = "GPIO Key F1";
> - linux,code = <KEY_F1>;
> - gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
> - };
> -
> - f2 {
> - label = "GPIO Key F2";
> - linux,code = <KEY_F2>;
> - gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
> - };
> -
> - f3 {
> - label = "GPIO Key F3";
> - linux,code = <KEY_F3>;
> - gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
> - };
> -
> - f4 {
> - label = "GPIO Key F4";
> - linux,code = <KEY_F4>;
> - gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
> - };
> -
> - f5 {
> - label = "GPIO Key F5";
> - linux,code = <KEY_F5>;
> - gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
> - };
> -
> - f6 {
> - label = "GPIO Key F6";
> - linux,code = <KEY_F6>;
> - gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
> - };
> -
> - f7 {
> - label = "GPIO Key F7";
> - linux,code = <KEY_F7>;
> - gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
> - };
> -
> - f8 {
> - label = "GPIO Key F8";
> - linux,code = <KEY_F8>;
> - gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
> - };
> -
> - f9 {
> - label = "GPIO Key F9";
> - linux,code = <KEY_F9>;
> - gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
> - };
> -
> - f10 {
> - label = "GPIO Key F10";
> - linux,code = <KEY_F10>;
> - gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
> - };
> - };
> -
> - leds {
> - compatible = "gpio-leds";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_leds>;
> -
> - led-debug0 {
> - function = LED_FUNCTION_STATUS;
> - gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "heartbeat";
> - };
> - };
> -
> - panel {
> - compatible = "innolux,g070y2t0ec";
> - backlight = <&backlight_lcd>;
> -
> - port {
> - panel_in: endpoint {
> - remote-endpoint = <&display_out>;
> - };
> - };
> - };
> -
> - reg_12v_bl: regulator-bl-12v {
> - compatible = "regulator-fixed";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_reg_12v_bl>;
> - regulator-name = "12v-bl";
> - regulator-min-microvolt = <12000000>;
> - regulator-max-microvolt = <12000000>;
> - gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - };
> -
> - reg_1v8: regulator-1v8 {
> - compatible = "regulator-fixed";
> - regulator-name = "1v8";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> -
> - sound {
> - compatible = "simple-audio-card";
> - simple-audio-card,name = "prti6q-sgtl5000";
> - simple-audio-card,format = "i2s";
> - simple-audio-card,widgets =
> - "Microphone", "Microphone Jack",
> - "Line", "Line In Jack",
> - "Headphone", "Headphone Jack",
> - "Speaker", "External Speaker";
> - simple-audio-card,routing =
> - "MIC_IN", "Microphone Jack",
> - "LINE_IN", "Line In Jack",
> - "Headphone Jack", "HP_OUT",
> - "External Speaker", "LINE_OUT";
> -
> - simple-audio-card,cpu {
> - sound-dai = <&ssi1>;
> - system-clock-frequency = <0>;
> - };
> -
> - simple-audio-card,codec {
> - sound-dai = <&sgtl5000>;
> - bitclock-master;
> - frame-master;
> - };
> - };
> -};
> -
> -&clks {
> - assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
> - assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
> -};
> -
> -&ecspi2 {
> - cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi2>;
> - status = "okay";
> -
> - tsc@0 {
> - compatible = "ti,tsc2046";
> - reg = <0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_tsc>;
> - spi-max-frequency = <100000>;
> - interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
> - pendown-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
> - vcc-supply = <®_3v3>;
> -
> - ti,vref-delay-usecs = /bits/ 16 <100>;
> -
> - ti,x-min = /bits/ 16 <0>;
> - ti,x-max = /bits/ 16 <8000>;
> - ti,y-min = /bits/ 16 <0>;
> - ti,y-max = /bits/ 16 <4800>;
> - ti,x-plate-ohms = /bits/ 16 <800>;
> - ti,y-plate-ohms = /bits/ 16 <300>;
> - ti,pressure-max = /bits/ 16 <4095>;
> -
> - ti,skip-samples = <2>;
> - ti,sample-period-msecs = <10>;
> - ti,report-period-msecs = <30>;
> -
> - ti,filter-tolerance = <80>;
> - ti,touch-resistance-threshold = <3500>;
> - };
> -};
> -
> -&audmux {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_audmux>;
> - status = "okay";
> -
> - mux_ssi1 {
> - fsl,audmux-port = <0>;
> - fsl,port-config = <
> - IMX_AUDMUX_V2_PTCR_SYN 0
> - IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
> - IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
> - IMX_AUDMUX_V2_PTCR_TFSDIR 0
> - IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> - >;
> - };
> -
> - mux_pins3 {
> - fsl,audmux-port = <2>;
> - fsl,port-config = <
> - IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> - 0 IMX_AUDMUX_V2_PDCR_TXRXEN
> - >;
> - };
> -};
> -
> -&can1 {
> - pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
> -};
> -
> -&i2c1 {
> - sgtl5000: codec@a {
> - compatible = "fsl,sgtl5000";
> - reg = <0xa>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_codec>;
> - #sound-dai-cells = <0>;
> - clocks = <&clks 201>;
> - VDDA-supply = <®_3v3>;
> - VDDIO-supply = <®_3v3>;
> - VDDD-supply = <®_1v8>;
> - };
> -};
> -
> -&i2c3 {
> - rtc@51 {
> - compatible = "nxp,pcf8563";
> - reg = <0x51>;
> - };
> -
> - gpio_pca: gpio@74 {
> - compatible = "nxp,pca9539";
> - reg = <0x74>;
> - interrupts-extended = <&gpio4 5 IRQ_TYPE_LEVEL_LOW>;
> - #gpio-cells = <2>;
> - gpio-controller;
> - };
> -};
> -
> -&ipu1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ipu1_csi0>;
> - status = "okay";
> -};
> -
> -&ipu1_di0_disp0 {
> - remote-endpoint = <&display_in>;
> -};
> -
> -&pwm1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_pwm1>;
> - status = "okay";
> -};
> -
> -&snvs_poweroff {
> - status = "okay";
> -};
> -
> -&snvs_pwrkey {
> - status = "okay";
> -};
> -
> -&ssi1 {
> - #sound-dai-cells = <0>;
> - fsl,mode = "i2s-slave";
> - status = "okay";
> -};
> -
> -&usbh1 {
> - status = "disabled";
> -};
> -
> -&vpu {
> - status = "disabled";
> -};
> -
> -&iomuxc {
> - pinctrl_audmux: audmuxgrp {
> - fsl,pins = <
> - MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> - MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> - MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> - MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> - MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> - >;
> - };
> -
> - pinctrl_can1phy: can1phy {
> - fsl,pins = <
> - /* CAN1_SR */
> - MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
> - /* CAN1_TERM */
> - MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
> - >;
> - };
> -
> - pinctrl_codec: codecgrp {
> - fsl,pins = <
> - /* AUDIO_nRESET */
> - MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
> - >;
> - };
> -
> - pinctrl_ecspi2: ecspi2grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> - MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> - MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> - MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> - >;
> - };
> -
> - pinctrl_ipu1_csi0: ipu1csi0grp {
> - fsl,pins = <
> - MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0
> - MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0
> - MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0
> - MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0
> - MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0
> - MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0
> - MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0
> - MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0
> - MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
> - /* ITU656_nRESET */
> - MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
> - /* ITU656_nPDN */
> - MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
> - >;
> - };
> -
> - pinctrl_ipu1_disp: ipudisp1grp {
> - fsl,pins = <
> - MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0xb0
> - MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xb0
> -
> - MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xb0
> - MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xb0
> - MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xb0
> - MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xb0
> - MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xb0
> - MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xb0
> - MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xb0
> - MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xb0
> -
> - MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xb0
> - MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xb0
> - MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xb0
> - MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xb0
> - MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xb0
> - MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xb0
> - MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xb0
> - MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xb0
> -
> - MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xb0
> - MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xb0
> - MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xb0
> - MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xb0
> - MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xb0
> - MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xb0
> - MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xb0
> - MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xb0
> - >;
> - };
> -
> - pinctrl_leds: ledsgrp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> - >;
> - };
> -
> - pinctrl_pwm1: pwm1grp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
> - >;
> - };
> -
> - pinctrl_reg_12v_bl: 12blgrp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0
> - >;
> - };
> -
> - pinctrl_tsc: tscgrp {
>
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b0
> - MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
> - >;
> - };
> -};
> +#include <arm/imx6dl-prtvt7.dts>
> +#include "imx6qdl-prti6q-emmc.dtsi"
> diff --git a/arch/arm/dts/imx6dl-victgo.dts b/arch/arm/dts/imx6dl-victgo.dts
> index 55bc4c8d41..250cd761d4 100644
> --- a/arch/arm/dts/imx6dl-victgo.dts
> +++ b/arch/arm/dts/imx6dl-victgo.dts
> @@ -1,145 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2016 Protonic Holland
> - */
> -
> /dts-v1/;
> -#include <arm/imx6dl.dtsi>
> -#include "imx6qdl-vicut1.dtsi"
> -#include <dt-bindings/input/input.h>
> -
> -/ {
> - model = "Kverneland Tellus GO";
> - compatible = "kvg,victgo", "fsl,imx6dl";
> -
> - memory {
> - reg = <0x10000000 0x20000000>;
> - };
> -
> - rotary-encoder {
> - compatible = "rotary-encoder";
> - pinctrl-0 = <&pinctrl_rotary_ch>;
> - gpios = <&gpio2 3 0>, <&gpio2 4 0>;
> - linux,axis = <8>; /* REL_WHEEL */
> - rotary-encoder,steps-per-period = <4>;
> - rotary-encoder,relative-axis;
> - rotary-encoder,rollover;
> - wakeup-source;
> - };
> -
> - rotary-button {
> - compatible = "gpio-keys";
> - pinctrl-0 = <&pinctrl_rotary_btn>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - autorepeat;
> - button@0 {
> - label = "Rotary Key";
> - gpios = <&gpio2 05 1>;
> - linux,code = <KEY_ENTER>;
> - gpio-key,wakeup;
> - };
> - };
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rmii";
> - phy-reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> - clocks = <&clks IMX6QDL_CLK_ENET>,
> - <&clks IMX6QDL_CLK_ENET>;
> - clock-names = "ipg", "ahb";
> - status = "okay";
> -};
> -
> -&uart2 {
> - status = "disabled";
> -};
> -
> -&i2c1 {
> - ht16k33: ht16k33@70 {
> - compatible = "holtek,ht16k33";
> - pinctrl-0 = <&pinctrl_ht16k33>;
> - reg = <0x70>;
> - refresh-rate-hz = <20>;
> - debounce-delay-ms = <50>;
> - interrupt-parent = <&gpio4>;
> - interrupts = <5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
> - keypad,num-rows = <12>;
> - keypad,num-columns = <3>;
> - linux,keymap = <
> - MATRIX_KEY(2, 0, KEY_F6)
> - MATRIX_KEY(3, 0, KEY_F8)
> - MATRIX_KEY(4, 0, KEY_F10)
> - MATRIX_KEY(5, 0, KEY_F4)
> - MATRIX_KEY(6, 0, KEY_F2)
> - MATRIX_KEY(2, 1, KEY_F5)
> - MATRIX_KEY(3, 1, KEY_F7)
> - MATRIX_KEY(4, 1, KEY_F9)
> - MATRIX_KEY(5, 1, KEY_F3)
> - MATRIX_KEY(6, 1, KEY_F1)
> - >;
> - };
> -};
> -
> -&pwm2 {
> - status = "disabled";
> -};
> -
> -&iomuxc {
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP4 */
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
> - MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> - MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
> - MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
> - /* Phy reset */
> - MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
> - /* nINTRP */
> - MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0
> - >;
> - };
> -
> - pinctrl_ecspi2: ecspi2grp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x100b1
> - MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO 0x100b1
> - MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
> - MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK 0x100b1
> - >;
> - };
> -
> - pinctrl_rotary_ch: rotarygrp {
> - fsl,pins = <
> - MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0 /* ROTARY_A */
> - MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0 /* ROTARY_B */
> - >;
> - };
> -
> - pinctrl_rotary_btn: rotarygrp {
> - fsl,pins = <
> - MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x1b0b0 /* ROTARY_BTN */
> - >;
> - };
> -
> - pinctrl_ht16k33: ht16k33grp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 /* IRQ */
> - >;
> - };
>
> - pinctrl_tsc2046e: tsc2046egrp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0
> - MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0
> - >;
> - };
> -};
> +#include <arm/imx6dl-victgo.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6dl-vicut1.dts b/arch/arm/dts/imx6dl-vicut1.dts
> index 725acbefc5..99cc7af2e6 100644
> --- a/arch/arm/dts/imx6dl-vicut1.dts
> +++ b/arch/arm/dts/imx6dl-vicut1.dts
> @@ -1,51 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> /dts-v1/;
> -#include <arm/imx6dl.dtsi>
> -#include "imx6qdl-vicut1.dtsi"
> -
> -/ {
> - model = "Kverneland UT1 Board";
> - compatible = "kvg,vicut1", "fsl,imx6dl";
> -
> - memory {
> - reg = <0x10000000 0x80000000>;
> - };
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rgmii";
> - status = "okay";
> -};
> -
> -&iomuxc {
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP_RGMII_MD(0x1b030, 0x10030) */
> - MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> - MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> - MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> - MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> - MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> - MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> - MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> - MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> - MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> - MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> - MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> - MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> - MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
>
> - /* Phy reset */
> - MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
> - >;
> - };
> -};
> +#include <arm/imx6dl-vicut1.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6q-prti6q.dts b/arch/arm/dts/imx6q-prti6q.dts
> index 21e24222a0..71606b892c 100644
> --- a/arch/arm/dts/imx6q-prti6q.dts
> +++ b/arch/arm/dts/imx6q-prti6q.dts
> @@ -1,532 +1,5 @@
> -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> +// SPDX-License-Identifier: GPL-2.0-or-later
> /dts-v1/;
> -#include <arm/imx6q.dtsi>
> -#include "imx6qdl-prti6q.dtsi"
> -#include "imx6qdl-prti6q-nor.dtsi"
> -#include <dt-bindings/leds/common.h>
> -#include <dt-bindings/sound/fsl-imx-audmux.h>
> -
> -/ {
> - model = "Protonic PRTI6Q board";
> - compatible = "prt,prti6q", "fsl,imx6q";
> -
> - memory@10000000 {
> - device_type = "memory";
> - reg = <0x10000000 0xf0000000>;
> - };
> -
> - backlight_lcd: backlight-lcd {
> - compatible = "pwm-backlight";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_backlight>;
> - pwms = <&pwm1 0 5000000 0>;
> - brightness-levels = <0 16 64 255>;
> - num-interpolated-steps = <16>;
> - default-brightness-level = <16>;
> - power-supply = <®_3v3>;
> - enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> - };
> -
> - can3_25m_osc: can3-25m-osc {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <25000000>;
> - };
> -
> - leds {
> - compatible = "gpio-leds";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_leds>;
> -
> - led-debug0 {
> - function = LED_FUNCTION_STATUS;
> - gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "heartbeat";
> - };
> -
> - led-debug1 {
> - function = LED_FUNCTION_SD;
> - gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "disk-activity";
> - };
> - };
> -
> - panel {
> - compatible = "kyo,tcg121xglp";
> - backlight = <&backlight_lcd>;
> -
> - port {
> - panel_in: endpoint {
> - remote-endpoint = <&lvds0_out>;
> - };
> - };
> - };
> -
> - reg_wifi: regulator-wifi {
> - compatible = "regulator-fixed";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_wifi_npd>;
> - enable-active-high;
> - gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> - regulator-max-microvolt = <1800000>;
> - regulator-min-microvolt = <1800000>;
> - regulator-name = "regulator-WL12xx";
> - startup-delay-us = <70000>;
> - };
> -
> - sound {
> - compatible = "simple-audio-card";
> - simple-audio-card,name = "prti6q-sgtl5000";
> - simple-audio-card,format = "i2s";
> - simple-audio-card,widgets =
> - "Microphone", "Microphone Jack",
> - "Line", "Line In Jack",
> - "Headphone", "Headphone Jack",
> - "Speaker", "External Speaker";
> - simple-audio-card,routing =
> - "MIC_IN", "Microphone Jack",
> - "LINE_IN", "Line In Jack",
> - "Headphone Jack", "HP_OUT",
> - "External Speaker", "LINE_OUT";
> -
> - simple-audio-card,cpu {
> - sound-dai = <&ssi1>;
> - system-clock-frequency = <0>;
> - };
> -
> - simple-audio-card,codec {
> - sound-dai = <&sgtl5000>;
> - bitclock-master;
> - frame-master;
> - };
> - };
> -
> - sound-spdif {
> - compatible = "fsl,imx-audio-spdif";
> - model = "imx-spdif";
> - spdif-controller = <&spdif>;
> - spdif-in;
> - spdif-out;
> - };
> -};
> -
> -&audmux {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_audmux>;
> - status = "okay";
> -
> - mux_ssi1 {
> - fsl,audmux-port = <0>;
> - fsl,port-config = <
> - IMX_AUDMUX_V2_PTCR_SYN 0
> - IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
> - IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
> - IMX_AUDMUX_V2_PTCR_TFSDIR 0
> - IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
> - >;
> - };
> -
> - mux_pins3 {
> - fsl,audmux-port = <2>;
> - fsl,port-config = <
> - IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
> - 0 IMX_AUDMUX_V2_PDCR_TXRXEN
> - >;
> - };
> -};
> -
> -&can2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_can2>;
> - status = "okay";
> -};
> -
> -&ecspi1 {
> - cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi1>;
> - status = "okay";
> -
> - flash@0 {
> - compatible = "jedec,spi-nor";
> - reg = <0>;
> - spi-max-frequency = <20000000>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - };
> -};
> -
> -&ecspi2 {
> - cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
> - status = "okay";
> -
> - can@0 {
> - compatible = "microchip,mcp2515";
> - reg = <0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_can3>;
> - clocks = <&can3_25m_osc>;
> - interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
> - spi-max-frequency = <5000000>;
> - };
> -
> - adc@1 {
> - compatible = "ti,adc128s052";
> - reg = <1>;
> - spi-max-frequency = <2000000>;
> - vref-supply = <®_3v3>;
> - };
> -};
> -
> -&ecspi3 {
> - cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi3>;
> - status = "okay";
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rgmii-id";
> - phy-handle = <&rgmii_phy>;
> - status = "okay";
> -
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - /* Microchip KSZ9031RNX PHY */
> - rgmii_phy: ethernet-phy@4 {
> - reg = <0>;
> - interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
> - reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> - reset-assert-us = <10000>;
> - reset-deassert-us = <300>;
> - };
> - };
> -};
> -
> -&hdmi {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hdmi>;
> - ddc-i2c-bus = <&i2c2>;
> - status = "okay";
> -};
> -
> -&i2c1 {
> - sgtl5000: audio-codec@a {
> - compatible = "fsl,sgtl5000";
> - reg = <0xa>;
> - #sound-dai-cells = <0>;
> - clocks = <&clks 201>;
> - VDDA-supply = <®_3v3>;
> - VDDIO-supply = <®_3v3>;
> - VDDD-supply = <®_1v8>;
> - };
> -};
> -
> -/* DDC */
> -&i2c2 {
> - clock-frequency = <100000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c2>;
> - status = "okay";
> -};
> -
> -&i2c3 {
> - adc@49 {
> - compatible = "ti,ads1015";
> - reg = <0x49>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - /* can2_l */
> - channel@4 {
> - reg = <4>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> -
> - /* can2_h */
> - channel@5 {
> - reg = <5>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> -
> - /* can1_l */
> - channel@6 {
> - reg = <6>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> -
> - /* can1_h */
> - channel@7 {
> - reg = <7>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> - };
> -};
>
> -&pcie {
> - status = "okay";
> -};
> -
> -&pwm1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_pwm1>;
> - status = "okay";
> -};
> -
> -&ldb {
> - status = "okay";
> -
> - lvds-channel@0 {
> - status = "okay";
> -
> - port@4 {
> - reg = <4>;
> -
> - lvds0_out: endpoint {
> - remote-endpoint = <&panel_in>;
> - };
> - };
> - };
> -};
> -
> -&sata {
> - status = "okay";
> -};
> -
> -&snvs_poweroff {
> - status = "okay";
> -};
> -
> -&spdif {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_spdif>;
> - status = "okay";
> -};
> -
> -&ssi1 {
> - #sound-dai-cells = <0>;
> - fsl,mode = "ac97-slave";
> - status = "okay";
> -};
> -
> -&uart2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart2>;
> - status = "okay";
> -};
> -
> -&uart5 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart5>;
> - status = "okay";
> -};
> -
> -&usbotg {
> - pinctrl-0 = <&pinctrl_usbotg &pinctrl_usbotg_id>;
> -};
> -
> -&usdhc2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc2>;
> - non-removable;
> - vmmc-supply = <®_wifi>;
> - cap-power-off-card;
> - keep-power-in-suspend;
> - status = "okay";
> -
> - wifi {
> - compatible = "ti,wl1271";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_wifi>;
> - interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
> - ref-clock-frequency = "38400000";
> - tcxo-clock-frequency = "19200000";
> - };
> -};
> -
> -&iomuxc {
> - pinctrl_audmux: audmuxgrp {
> - fsl,pins = <
> - MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> - MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
> - MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> - MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> - MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> - >;
> - };
> -
> - pinctrl_backlight: backlightgrp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
> - >;
> - };
> -
> - pinctrl_can2: can2grp {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000
> - MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000
> - >;
> - };
> -
> - pinctrl_can3: can3grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
> - >;
> - };
> -
> - pinctrl_ecspi1: ecspi1grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> - MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> - MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> - /* CS */
> - MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
> - >;
> - };
> -
> - pinctrl_ecspi2: ecspi2grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> - MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> - MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> - MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> - >;
> - };
> -
> - pinctrl_ecspi2_cs: ecspi2csgrp {
> - fsl,pins = <
> - /* ADC128S022 CS */
> - MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
> - >;
> - };
> -
> - pinctrl_ecspi3: ecspi3grp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
> - MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
> - MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
> - MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
> - >;
> - };
> -
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> - MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> - MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> - MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> - MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> - MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> - MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> - MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> - MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> - MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> - MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> - MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> - MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
> -
> - /* Phy reset */
> - MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
> - >;
> - };
> -
> - pinctrl_hdmi: hdmigrp {
> - fsl,pins = <
> - /* NOTE: DDC is done via I2C2, so DON'T
> - * configure DDC pins for HDMI!
> - */
> - MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> - >;
> - };
> -
> - /* DDC */
> - pinctrl_i2c2: i2c2grp {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> - MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> - >;
> - };
> -
> - pinctrl_leds: ledsgrp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> - MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
> - >;
> - };
> -
> - pinctrl_pwm1: pwm1grp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
> - >;
> - };
> -
> - pinctrl_spdif: spdifgrp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
> - MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
> - >;
> - };
> -
> - pinctrl_uart2: uart2grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
> - MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
> - MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
> - MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
> - >;
> - };
> -
> - pinctrl_uart5: uart5grp {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
> - MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
> - >;
> - };
> -
> - pinctrl_usbotg_id: usbotgidgrp {
> - fsl,pins = <
> - MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
> - >;
> - };
> -
> - pinctrl_usdhc2: usdhc2grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> - MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> - MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> - MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> - MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> - MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> - >;
> - };
> -
> - pinctrl_wifi: wifigrp {
> - fsl,pins = <
> - /* WL12xx IRQ */
> - MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
> - >;
> - };
> -
> - pinctrl_wifi_npd: wifinpd {
> - fsl,pins = <
> - MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
> - >;
> - };
> -};
> +#include <arm/imx6q-prti6q.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6q-prtwd2.dts b/arch/arm/dts/imx6q-prtwd2.dts
> index 8572917865..78ea4bc15c 100644
> --- a/arch/arm/dts/imx6q-prtwd2.dts
> +++ b/arch/arm/dts/imx6q-prtwd2.dts
> @@ -1,188 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2018 Protonic Holland
> - */
> -
> /dts-v1/;
> -#include <arm/imx6q.dtsi>
> -#include "imx6qdl-prti6q.dtsi"
> -#include <dt-bindings/leds/common.h>
> -
> -/ {
> - model = "Protonic WD2 board";
> - compatible = "prt,prtwd2", "fsl,imx6q";
> -
> - memory@10000000 {
> - device_type = "memory";
> - reg = <0x10000000 0x20000000>;
> - };
> -
> - memory@80000000 {
> - device_type = "memory";
> - reg = <0x80000000 0x20000000>;
> - };
> -
> - usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
> - compatible = "mmc-pwrseq-simple";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_wifi_npd>;
> - reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
> - };
> -
> - /* PRTWD2 rev 1 bitbang I2C for Ethernet Switch */
> - i2c@4 {
> - compatible = "i2c-gpio";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c4>;
> - sda-gpios = <&gpio1 22 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
> - scl-gpios = <&gpio1 31 GPIO_ACTIVE_HIGH>;
> - i2c-gpio,delay-us = <20>; /* ~10 kHz */
> - i2c-gpio,scl-output-only;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -};
> -
> -&can1 {
> - pinctrl-0 = <&pinctrl_can1 &pinctrl_can1phy>;
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rmii";
> - clocks = <&clks IMX6QDL_CLK_ENET>,
> - <&clks IMX6QDL_CLK_ENET>;
> - clock-names = "ipg", "ahb";
> - status = "okay";
> -
> - fixed-link {
> - speed = <100>;
> - pause;
> - full-duplex;
> - };
> -};
> -
> -&i2c3 {
> - adc@49 {
> - compatible = "ti,ads1015";
> - reg = <0x49>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - /* V in */
> - channel@4 {
> - reg = <4>;
> - ti,gain = <1>;
> - ti,datarate = <3>;
> - };
> -
> - /* I charge */
> - channel@5 {
> - reg = <5>;
> - ti,gain = <1>;
> - ti,datarate = <3>;
> - };
> -
> - /* V bus */
> - channel@6 {
> - reg = <6>;
> - ti,gain = <1>;
> - ti,datarate = <3>;
> - };
> -
> - /* nc */
> - channel@7 {
> - reg = <7>;
> - ti,gain = <1>;
> - ti,datarate = <3>;
> - };
> - };
> -};
> -
> -&usdhc2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc2>;
> - non-removable;
> - no-1-8-v;
> - non-removable;
> - mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
> - pm-ignore-notify;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - status = "okay";
> -
> - wifi@1 {
> - compatible = "brcm,bcm4329-fmac";
> - reg = <1>;
> - };
> -};
> -
> -&iomuxc {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usb_eth_chg>;
> -
> - pinctrl_can1phy: can1phy {
> - fsl,pins = <
> - /* CAN1_SR */
> - MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
> - >;
> - };
> -
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP4 */
> - MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x130b0
> - MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0
> - MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0
> - MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0
> - MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0
> -
> - MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0
> - /* Phy reset */
> - MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0
> - /* nINTRP */
> - MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0
> -
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
> - >;
> - };
> -
> - pinctrl_i2c4: i2c4grp {
> - fsl,pins = <
> - MX6QDL_PAD_ENET_MDIO__GPIO1_IO22 0x1f8b0
> - MX6QDL_PAD_ENET_MDC__GPIO1_IO31 0x1f8b0
> - >;
> - };
> -
> - pinctrl_usb_eth_chg: usbethchggrp {
> - fsl,pins = <
> - /* USB charging control */
> - MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x130b0
> - MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x130b0
> - MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x130b0
> - MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x130b0
> - >;
> - };
> -
> - pinctrl_usdhc2: usdhc2grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> - MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> - MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> - MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> - MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> - MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> - >;
> - };
>
> - pinctrl_wifi_npd: wifinpd {
> - fsl,pins = <
> - /* WL_REG_ON */
> - MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
> - >;
> - };
> -};
> +#include <arm/imx6q-prtwd2.dts>
> +#include "imx6qdl-prti6q-emmc.dtsi"
> diff --git a/arch/arm/dts/imx6q-vicut1.dts b/arch/arm/dts/imx6q-vicut1.dts
> index 9d1d6fa550..61fb56d401 100644
> --- a/arch/arm/dts/imx6q-vicut1.dts
> +++ b/arch/arm/dts/imx6q-vicut1.dts
> @@ -1,66 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> /dts-v1/;
> -#include <arm/imx6q.dtsi>
> -#include "imx6qdl-vicut1.dtsi"
> -
> -/ {
> - model = "Kverneland UT1Q Board";
> - compatible = "kvg,vicut1q", "fsl,imx6q";
> -
> - memory {
> - reg = <0x10000000 0xf0000000>;
> - };
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rgmii-id";
> - phy-handle = <&rgmii_phy>;
> - status = "okay";
> -
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - /* Microchip KSZ9031RNX PHY */
> - rgmii_phy: ethernet-phy@4 {
> - reg = <0>;
> - interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
> - reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> - reset-assert-us = <10000>;
> - reset-deassert-us = <300>;
> - };
> - };
> -};
> -
> -&iomuxc {
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP_RGMII_MD(0x1b030, 0x10030) */
> - MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> - MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> - MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> - MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> - MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> - MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> - MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> - MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> - MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> - MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> - MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> - MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> - MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
>
> - /* Phy reset */
> - MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
> - >;
> - };
> -};
> +#include <arm/imx6q-vicut1.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6qdl-prti6q-emmc.dtsi b/arch/arm/dts/imx6qdl-prti6q-emmc.dtsi
> new file mode 100644
> index 0000000000..4fc7bd6473
> --- /dev/null
> +++ b/arch/arm/dts/imx6qdl-prti6q-emmc.dtsi
> @@ -0,0 +1,49 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +
> +/ {
> + chosen {
> + stdout-path = &uart4;
> +
> + environment@0 {
> + compatible = "barebox,environment";
> + device-path = &usdhc3, "partname:barebox-environment";
> + };
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + /* Address will be determined by the bootloader */
> + ramoops {
> + compatible = "ramoops";
> + };
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + /* Address will be determined by the bootloader */
> + ramoops {
> + compatible = "ramoops";
> + };
> + };
> +};
> +
> +&usdhc3 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@40000 {
> + label = "barebox-environment";
> + reg = <0x40000 0x80000>;
> + };
> +
> + partition@c0000 {
> + label = "state";
> + reg = <0xc0000 0x40000>;
> + };
> +};
> diff --git a/arch/arm/dts/imx6qdl-prti6q-nor.dtsi b/arch/arm/dts/imx6qdl-prti6q-nor.dtsi
> index ad718ce421..7a88652b42 100644
> --- a/arch/arm/dts/imx6qdl-prti6q-nor.dtsi
> +++ b/arch/arm/dts/imx6qdl-prti6q-nor.dtsi
> @@ -1,7 +1,12 @@
> // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
>
> +#include "imx6qdl-prti6q-emmc.dtsi"
> +
> &ecspi1 {
> flash@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> partition@0 {
> label = "barebox";
> reg = <0x0 0x100000>;
> diff --git a/arch/arm/dts/imx6qdl-prti6q.dtsi b/arch/arm/dts/imx6qdl-prti6q.dtsi
> deleted file mode 100644
> index bfc059e34f..0000000000
> --- a/arch/arm/dts/imx6qdl-prti6q.dtsi
> +++ /dev/null
> @@ -1,216 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> -#include <dt-bindings/gpio/gpio.h>
> -#include <dt-bindings/input/input.h>
> -
> -/ {
> - chosen {
> - stdout-path = &uart4;
> -
> - environment-emmc {
> - compatible = "barebox,environment";
> - device-path = &usdhc3, "partname:barebox-environment";
> - };
> - };
> -
> - reserved-memory {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - /* Address will be determined by the bootloader */
> - ramoops {
> - compatible = "ramoops";
> - };
> - };
> -
> - reserved-memory {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges;
> -
> - /* Address will be determined by the bootloader */
> - ramoops {
> - compatible = "ramoops";
> - };
> - };
> -
> - reg_1v8: regulator-1v8 {
> - compatible = "regulator-fixed";
> - regulator-name = "1v8";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> -
> - reg_3v3: regulator-3v3 {
> - compatible = "regulator-fixed";
> - regulator-name = "3v3";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - };
> -
> - reg_usb_h1_vbus: regulator-h1-vbus {
> - compatible = "regulator-fixed";
> - regulator-name = "h1-vbus";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - regulator-always-on;
> - };
> -
> - reg_usb_otg_vbus: regulator-otg-vbus {
> - compatible = "regulator-fixed";
> - regulator-name = "otg-vbus";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - };
> -};
> -
> -&can1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_can1>;
> - status = "okay";
> -};
> -
> -&i2c1 {
> - clock-frequency = <100000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c1>;
> - status = "okay";
> -};
> -
> -&i2c3 {
> - clock-frequency = <100000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c3>;
> - status = "okay";
> -
> - temperature-sensor@70 {
> - compatible = "ti,tmp103";
> - reg = <0x70>;
> - };
> -};
> -
> -&uart4 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart4>;
> - status = "okay";
> -};
> -
> -&usbh1 {
> - vbus-supply = <®_usb_h1_vbus>;
> - phy_type = "utmi";
> - dr_mode = "host";
> - status = "okay";
> -};
> -
> -&usbotg {
> - vbus-supply = <®_usb_otg_vbus>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usbotg>;
> - phy_type = "utmi";
> - dr_mode = "host";
> - disable-over-current;
> - status = "okay";
> -};
> -
> -&usdhc1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc1>;
> - cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
> - status = "okay";
> -};
> -
> -&usdhc3 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc3>;
> - bus-width = <8>;
> - non-removable;
> - no-sdio;
> - no-sd;
> - status = "okay";
> -
> - #address-cells = <1>;
> - #size-cells = <1>;
> -
> - partition@100000 {
> - label = "barebox-environment";
> - reg = <0x100000 0x100000>;
> - };
> -
> - partition@200000 {
> - label = "state";
> - reg = <0x200000 0x100000>;
> - };
> -};
> -
> -&iomuxc {
> - pinctrl_can1: can1grp {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000
> - MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000
> - >;
> - };
> -
> - pinctrl_i2c1: i2c1grp {
> - fsl,pins = <
> - MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
> - MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
> - >;
> - };
> -
> - pinctrl_i2c3: i2c3grp {
> - fsl,pins = <
> - MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
> - MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> - >;
> - };
> -
> - pinctrl_uart4: uart4grp {
> - fsl,pins = <
> - MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> - MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> - >;
> - };
> -
> - pinctrl_usdhc1: usdhc1grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
> - MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
> - MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
> - MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
> - MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
> - MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
> - MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
> - >;
> - };
> -
> - pinctrl_usdhc3: usdhc3grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
> - MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
> - MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
> - MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
> - MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
> - MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
> - MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
> - MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
> - MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
> - MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
> - MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
> - >;
> - };
> -
> - pinctrl_usbotg: usbotggrp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> - MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
> - >;
> - };
> -};
> diff --git a/arch/arm/dts/imx6qdl-vicut1.dtsi b/arch/arm/dts/imx6qdl-vicut1.dtsi
> deleted file mode 100644
> index dbfcf2527c..0000000000
> --- a/arch/arm/dts/imx6qdl-vicut1.dtsi
> +++ /dev/null
> @@ -1,234 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> -#include "imx6qdl-prti6q.dtsi"
> -#include "imx6qdl-prti6q-nor.dtsi"
> -#include <dt-bindings/input/input.h>
> -
> -/ {
> - gpio_key_pwr: gpio_keys {
> - compatible = "gpio-keys";
> - autorepeat;
> -
> - power {
> - label = "GPIO Key Power";
> - gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
> - linux,code = <KEY_POWER>;
> - gpio-key,wakeup;
> - };
> - };
> -
> - leds {
> - compatible = "gpio-leds";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_leds>;
> -
> - debug0 {
> - label = "debug0";
> - gpios = <&gpio1 8 0>;
> - linux,default-trigger = "heartbeat";
> - };
> -
> - debug1 {
> - label = "debug1";
> - gpios = <&gpio1 9 0>;
> - linux,default-trigger = "mmc";
> - };
> -
> - power_led {
> - label = "power_led";
> - gpios = <&gpio2 24 0>;
> - default-state = "on";
> - };
> -
> - isb_led {
> - label = "isb_led";
> - gpios = <&gpio4 31 0>;
> - default-state = "off";
> - };
> - };
> -};
> -
> -&clks {
> - assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
> - assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
> -};
> -
> -&uart1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart1>;
> - status = "okay";
> -};
> -
> -&uart3 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart3>;
> - status = "okay";
> -};
> -
> -&i2c3 {
> - rtc: pcf8563@51 {
> - compatible = "nxp,pcf8563";
> - reg = <0x51>;
> - };
> -};
> -
> -&ecspi1 {
> - cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi1>;
> - status = "okay";
> -
> - flash@0 {
> - compatible = "jedec,spi-nor";
> - reg = <0>;
> - spi-max-frequency = <20000000>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> - };
> -};
> -
> -&iomuxc {
> - pinctrl_hog: hoggrp {
> - fsl,pins = <
> - /* SGTL5000 sys_mclk */
> - MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> - /* CAN1_SR + CAN2_SR GPIO outputs */
> - MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
> - MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
> - /* CAN1_TERM */
> - MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
> - /* ITU656_nRESET */
> - MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
> - /* CAM1_MIRROR */
> - MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0
> - /* CAM2_MIRROR */
> - MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0
> - /* CAM_nDETECT */
> - MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0
> - /* nON_SWITCH */
> - MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0
> - /* ISB_IN1 */
> - MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0
> - /* ISB_nIN2 */
> - MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0
> - /* WARN_LIGHT */
> - MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0
> - /* ON2_FB */
> - MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0
> - /* YACO_nIRQ */
> - MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0
> - /* YACO_BOOT0 */
> - MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0
> - /* YACO_nRESET */
> - MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0
> - /* FORCE_ON1 */
> - MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
> - /* AUDIO_nRESET */
> - MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0
> - /* ITU656_nPDN */
> - MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
> -
> - /* HW revision detect */
> - /* REV_ID0 */
> - MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
> - /* REV_ID1 = PWM output LED_PWM (SION) */
> - /* defined in &pinctrl_pwm3 */
> - /* REV_ID2 */
> - MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
> - /* REV_ID3 */
> - MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
> - /* REV_ID4 */
> - MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
> -
> - /* New in HW revision 1 */
> - MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0 /* ON1_FB */
> - MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 /* DIP1_FB */
> -
> - /* New in UTC (UT1 HW revision 1) and TGO */
> - /* WHEEL */
> - MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x100b0
> - /* RADAR */
> - MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x100b0
> - /* PTO */
> - MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x100b0
> - /* CPU_ON1_CTRL */
> - MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x1b0b0
> - /* CPU_ON2_CTRL */
> - MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x1b0b0
> - /* CPU_HITCH_IN_OUT */
> - MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x100b0
> - /* CPU_LIGHT_ON */
> - MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x100b0
> - /* CPU_CONTACT_IN */
> - MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x100b0
> - >;
> - };
> -
> - pinctrl_ecspi1: ecspi1grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
> - MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
> - MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
> - /* CS */
> - MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
> - >;
> - };
> -
> - pinctrl_usbotg: usbotggrp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
> - /* power enable, high active */
> - MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
> - >;
> - };
> -
> - /* YaCO AUX Uart */
> - pinctrl_uart1: uart1grp {
> - fsl,pins = <
> - MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
> - MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
> - >;
> - };
> -
> - /* YaCO Touchscreen UART */
> - pinctrl_uart3: uart3grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
> - MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
> - >;
> - };
> -
> - pinctrl_leds: ledsgrp {
> - fsl,pins = <
> - /* DEBUG0A */
> - MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0
> - /* DEBUG1A */
> - MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0
> - /* DEBUG0 */
> - MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
> - /* DEBUG1 */
> - MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
> - /* POWER_LED */
> - MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0
> - /* ISB_LED */
> - MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31 0x1b0b0
> - >;
> - };
> -
> - pinctrl_pwm2: pwm2grp {
> - fsl,pins = <
> - /* ISB LED (not in TGO or UTC version 1+) */
> - MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b0
> - >;
> - };
> -
> - pinctrl_pwm3: pwm3grp {
> - fsl,pins = <
> - /* REV_ID1 = PWM output LED_PWM (SION for ID) */
> - MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x4001b0b0
> - >;
> - };
> -};
> diff --git a/arch/arm/dts/imx6qp-prtwd3.dts b/arch/arm/dts/imx6qp-prtwd3.dts
> index 97b25ee26a..8c56d70b5a 100644
> --- a/arch/arm/dts/imx6qp-prtwd3.dts
> +++ b/arch/arm/dts/imx6qp-prtwd3.dts
> @@ -1,675 +1,6 @@
> -/*
> - * Copyright (c) 2018 Protonic Holland
> - *
> - * The code contained herein is licensed under the GNU General Public
> - * License. You may obtain a copy of the GNU General Public License
> - * Version 2 or later at the following locations:
> - *
> - * http://www.opensource.org/licenses/gpl-license.html
> - * http://www.gnu.org/copyleft/gpl.html
> - */
> -
> +// SPDX-License-Identifier: GPL-2.0-or-later
> /dts-v1/;
> -#include <arm/imx6qp.dtsi>
> -#include "imx6qdl-prti6q.dtsi"
> -
> -/ {
> - model = "Protonic WD3 board";
> - compatible = "prt,prtwd3", "fsl,imx6qp";
> -
> - memory@10000000 {
> - device_type = "memory";
> - reg = <0x10000000 0x20000000>;
> - };
> -
> - memory@80000000 {
> - device_type = "memory";
> - reg = <0x80000000 0x20000000>;
> - };
> -
> - aliases {
> - mdio-gpio0 = &mdio0;
> - };
> -
> - usdhc2_wifi_pwrseq: usdhc2_wifi_pwrseq {
> - compatible = "mmc-pwrseq-simple";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_wifi_npd>;
> - reset-gpios = <&gpio6 10 GPIO_ACTIVE_LOW>;
> - };
> -
> - clk20m_can: fdcan_clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <20000000>;
> - };
> -
> - clk25m_switch: switch_clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <25000000>;
> - };
> -
> - clk25m_phy3: phy3_clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <25000000>;
> - };
> -
> - clk50m_phy: phy_clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <50000000>;
> - };
> -
> - mdio0: mdio {
> - compatible = "virtual,mdio-gpio";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_mdio0>;
> -
> - #address-cells = <1>;
> - #size-cells = <0>;
> - gpios = <&gpio5 6 GPIO_ACTIVE_HIGH
> - &gpio5 7 GPIO_ACTIVE_HIGH>;
> - };
> -
> - display_panel0 {
> - compatible = "kyo,tcg121xglp";
> - backlight = <&backlight_lcd>;
> -
> - port {
> - display_panel0_in: endpoint {
> - remote-endpoint = <&serializer0_out>;
> - };
> - };
> - };
> -
> - display_panel1 {
> - compatible = "kyo,tcg121xglp";
> - backlight = <&backlight_panel1>;
> -
> - port {
> - display_panel1_in: endpoint {
> - remote-endpoint = <&serializer1_out>;
> - };
> - };
> - };
> -
> - backlight_lcd: backlight_lcd {
> - compatible = "pwm-backlight";
> - pwms = <&pwm1 0 5000000 0>;
> - brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192 255>;
> - default-brightness-level = <15>;
> - power-supply = <®_3v3>;
> - };
> -
> - backlight_panel1: backlight_panel1 {
> - compatible = "pwm-backlight";
> - pwms = <&pwm2 0 5000000 0>;
> - brightness-levels = <0 1 2 4 6 8 12 16 24 32 48 64 96 128 192 255>;
> - default-brightness-level = <0>;
> - power-supply = <®_3v3>;
> - };
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - status = "okay";
> -
> - clocks = <&clks IMX6QDL_CLK_ENET>,
> - <&clks IMX6QDL_CLK_ENET>,
> - <&clks IMX6QDL_CLK_ENET_REF>,
> - <&clks IMX6QDL_CLK_ENET_REF>;
> - clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
> - assigned-clocks = <&clks IMX6QDL_CLK_ENET_REF>;
> - assigned-clock-rates = <125000000>;
> -
> - phy-mode = "rgmii";
> - fixed-link {
> - speed = <100>;
> - full-duplex;
> - };
> -
> - mdio1: mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - /* Microchip KSZ9031 */
> - rgmii_phy: ethernet-phy@2 {
> - compatible = "ethernet-phy-ieee802.3-c22";
> - reg = <2>;
> -
> - interrupts-extended = <&gpio1 28 IRQ_TYPE_EDGE_FALLING>;
> -
> - /* FIXME: tx/rx clk skew are currently set by imx
> - * platform driver. Write own walues here to not depend
> - * fixup of horror.
> - */
> -
> - reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> - /* reset assert time is provided by documentation */
> - reset-assert-us = <10000>;
> - /* documented reset deassert time (100us) is not enough
> - * use test value of 300us.
> - */
> - reset-deassert-us = <1000>;
> -
> - clocks = <&clk25m_phy3>;
> - };
> - };
> -};
> -
> -&ecspi2 {
> - fsl,spi-num-chipselects = <1>;
> - cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi2>;
> - status = "okay";
> - sja1105_switch: sja1105@0 {
> - reg = <0>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - compatible = "nxp,sja1105q";
> - spi-max-frequency = <4000000>;
> - spi-cpha;
> - spi-rx-delay-us = <1>;
> - spi-tx-delay-us = <1>;
> -
> - reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
> -
> - clocks = <&clk25m_switch>;
> - #clock-cells = <1>;
> -
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - port@0 {
> - reg = <0>;
> - label = "usb";
> - phy-handle = <&usbeth_phy>;
> - phy-mode = "rmii";
> - };
> -
> - port@1 {
> - reg = <1>;
> - label = "t1slave";
> - phy-handle = <&tja1102_phy1>;
> - phy-mode = "rmii";
> - };
> -
> - port@2 {
> - reg = <2>;
> - label = "t1master";
> - phy-handle = <&tja1102_phy0>;
> - phy-mode = "rmii";
> -
> - };
> -
> - port@3 {
> - reg = <3>;
> - label = "rj45";
> - phy-handle = <&rgmii_phy>;
> - phy-mode = "rgmii-id";
> - };
> -
> - port@4 {
> - reg = <4>;
> - label = "cpu";
> - ethernet = <&fec>;
> - phy-mode = "rgmii-id";
> -
> - fixed-link {
> - speed = <100>;
> - full-duplex;
> - };
> - };
> - };
> - };
> -};
> -
> -&mdio0 {
> - usbeth_phy: ethernet-phy@3 {
> - compatible = "ethernet-phy-ieee802.3-c22";
> - reg = <0x3>;
> -
> - interrupts-extended = <&gpio5 12 IRQ_TYPE_LEVEL_LOW>;
> - micrel,led-mode = <0>;
> -
> - reset-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
> - reset-assert-us = <500>;
> - reset-deassert-us = <1000>;
> -
> - /* FIXME: the clock is provided by switch and we should know
> - * and we should request it only after switch have done clock
> - * configuration. Since it is currently not implemented,
> - * use fixed clock.
> - * WARNING: Using fixed clocks in this case is potential source
> - * for evil bugs. Switch may reconfigure, stop or change clk
> - * freq without letting PHY to know about it.
> - */
> - clocks = <&clk50m_phy>;
> - clock-names = "rmii-ref";
> - };
> -
> - tja1102_phy0: ethernet-phy@4 {
> - compatible = "ethernet-phy-id0180.dc80";
> - reg = <0x4>;
> -
> - interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
> -
> - reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
> - /* reset detection time is 20 usec. */
> - reset-assert-us = <20>;
> - /* reset to standby 2 msec. */
> - reset-deassert-us = <2000>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - tja1102_phy1: ethernet-phy@5 {
> - reg = <0x5>;
> -
> - interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
> - };
> - };
> -};
> -
> -&ecspi3 {
> - fsl,spi-num-chipselects = <1>;
> - cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi3>;
> - status = "okay";
> - can3: can@0 {
> - compatible = "microchip,mcp2518fd";
> - spi-max-frequency = <5000000>;
> - reg = <0>;
> - clocks = <&clk20m_can>;
> - interrupt-parent = <&gpio4>;
> - interrupts = <25 0x2>;
> - };
> -};
> -
> -&i2c1 {
> - clock-frequency = <100000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c1>;
> - status = "okay";
> -
> - serializer0: ds90ub927@c {
> - compatible = "ti,ds90ub927";
> - reg = <0x0c>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - port@0 {
> - reg = <0>;
> - serializer0_in: endpoint {
> - remote-endpoint = <&lvds0_out>;
> - };
> - };
> - /* port@1 {
> - reg = <1>;
> - serializer0_audio_in: endpoint {
> - remote-endpoint = <&audio_i2s0_out>;
> - };
> - }; */
> - port@2 {
> - reg = <2>;
> - serializer0_out: endpoint {
> - remote-endpoint = <&display_panel0_in>;
> - };
> - };
> - };
> -};
> -
> -&i2c2 {
> - clock-frequency = <100000>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c2>;
> - status = "okay";
> -
> - serializer1: ds90ub927@c {
> - compatible = "ti,ds90ub927";
> - reg = <0x0c>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - port@0 {
> - reg = <0>;
> - serializer1_in: endpoint {
> - remote-endpoint = <&lvds1_out>;
> - };
> - };
> - port@2 {
> - reg = <2>;
> - serializer1_out: endpoint {
> - remote-endpoint = <&display_panel1_in>;
> - };
> - };
> - };
> -
> - camdeser: ds90ub954@30 {
> - compatible = "ti,ds90ub954";
> - reg = <0x30>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> - port@0 {
> - reg = <0>;
> - camdeser_fpd_link_in: endpoint {
> - };
> - };
> - port@1 {
> - reg = <1>;
> - camdeser_mipi_out: endpoint {
> - remote-endpoint = <&mipi_csi_in>;
> - };
> - };
> - };
> -};
> -
> -&usdhc2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc2>;
> - no-1-8-v; /* force 3.3V VIO */
> - non-removable;
> - mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
> - pm-ignore-notify;
> - status = "okay";
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - brcmf: bcrmf@1 {
> - reg = <1>;
> - compatible = "brcm,bcm4329-fmac";
> - };
> -};
> -
> -&i2c3 {
> - adc@49 {
> - compatible = "ti,ads1015";
> - reg = <0x49>;
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - channel@4 {
> - reg = <4>;
> - ti,gain = <1>;
> - ti,datarate = <3>;
> - };
> -
> - channel@5 {
> - reg = <5>;
> - ti,gain = <1>;
> - ti,datarate = <3>;
> - };
> -
> - channel@6 {
> - reg = <6>;
> - ti,gain = <1>;
> - ti,datarate = <3>;
> - };
> -
> - channel@7 {
> - reg = <7>;
> - ti,gain = <1>;
> - ti,datarate = <3>;
> - };
> - };
> -};
> -
> -&ldb {
> - status = "okay";
> -
> - lvds-channel@0 {
> - status = "okay";
> -
> - port@4 {
> - reg = <4>;
> -
> - lvds0_out: endpoint {
> - remote-endpoint = <&serializer0_in>;
> - };
> - };
> - };
> -
> - lvds-channel@1 {
> - status = "okay";
> -
> - port@4 {
> - reg = <4>;
> -
> - lvds1_out: endpoint {
> - remote-endpoint = <&serializer1_in>;
> - };
> - };
> - };
> -};
> -
> -&mipi_csi {
> - status = "okay";
> - port@0 {
> - reg = <0>;
> -
> - mipi_csi_in: endpoint {
> - remote-endpoint = <&camdeser_mipi_out>;
> - };
> - };
> -};
> -
> -&ipu1_csi0_mux_from_parallel_sensor {
> - /* Empty, to disable parallel camera from PRTI6Q */
> -};
> -
> -&pwm1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_pwm1>;
> - status = "okay";
> -};
> -
> -&pwm2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_pwm2>;
> - status = "okay";
> -};
> -
> -&iomuxc {
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> - MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> - MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> - MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> - MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> - MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> - MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> - MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> - MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> - MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> - MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> - MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> -
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
> -
> - /* Configure clock provider for RGMII ref clock */
> - MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0b0
> - /* Configure clock consumer for RGMII ref clock */
> - MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> -
> - /* SJA1105Q switch reset */
> - MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x10030
> -
> - /* phy3/rgmii_phy reset */
> - MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x10030
> - /* phy3/rgmii_phy int */
> - MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x40010000
> - >;
> - };
> -
> - pinctrl_mdio0: mdio0grp {
> - fsl,pins = <
> - /* phy0/usbeth_phy reset */
> - MX6QDL_PAD_DISP0_DAT17__GPIO5_IO11 0x10030
> - /* phy0/usbeth_phy int */
> - MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1
> -
> - /* phy12/tja1102_phy0 reset */
> - MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x10030
> - /* phy12/tja1102_phy0 int */
> - MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x100b1
> - /* phy12/tja1102_phy0 enable. Set 100K pull-up */
> - MX6QDL_PAD_DISP0_DAT16__GPIO5_IO10 0x1f030
> - >;
> - };
> -
> - pinctrl_ecspi2: ecspi2grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> - MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> - MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> - MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> - >;
> - };
> -
> -
> -
> - pinctrl_hog: hoggrp {
> - fsl,pins = <
> - /* SGTL5000 sys_mclk */
> - MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
> - /* CAN1_SR + CAN2_SR GPIO outputs */
> - MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13070
> - MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13070
> - /* CAN1_TERM (not used on WD3) */
> - MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
> -
> - /* HW revision detect */
> - /* REV_ID0 */
> - MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
> - /* REV_ID1 */
> - MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
> - /* REV_ID2 */
> - MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0
> - /* REV_ID3 */
> - MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0
> - /* REV_ID4 */
> - MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0
> -
> - /* USB charging control */
> - /* CHG Control */
> - MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x130b0
> - /* RID0 */
> - MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x130b0
> - /* RID1 */
> - MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x130b0
> - /* RID2 */
> - MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x130b0
> -
> - /* Power VSEL and TG */
> - /* VSEL */
> - MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x1b0b0
> - /* TG */
> - MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x1b0b0
> -
> - /* Display panel 0 GPIO */
> - /* L/R */
> - MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28 0x1b0b0
> - /* TS_nINT */
> - MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x1b0b0
> - /* EN */
> - MX6QDL_PAD_CSI0_DAT12__GPIO5_IO30 0x1b0b0
> - /* LVDS0_nINT */
> - MX6QDL_PAD_CSI0_DAT14__GPIO6_IO00 0x1b0b0
> - /* LVDS0_PD */
> - MX6QDL_PAD_CSI0_DAT15__GPIO6_IO01 0x1b0b0
> -
> - /* Display panel 1 GPIO */
> - /* L/R */
> - MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19 0x1b0b0
> - /* TS_nINT */
> - MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0
> - /* EN */
> - MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x1b0b0
> - /* LVDS1_nINT */
> - MX6QDL_PAD_CSI0_DAT7__GPIO5_IO25 0x1b0b0
> - /* LVDS1_PD */
> - MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1b0b0
> -
> - /* Camera */
> - /* CAM_GPIO0 */
> - MX6QDL_PAD_CSI0_DAT13__GPIO5_IO31 0x1b0b0
> - /* CAM_nINT */
> - MX6QDL_PAD_CSI0_DAT16__GPIO6_IO02 0x1b0b0
> - /* CAM_GPIO1 */
> - MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03 0x1b0b0
> - /* CAM_nPD */
> - MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04 0x1b0b0
> - /* CAM_LOCK */
> - MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05 0x1b0b0
> -
> - /* USB ethernet reset (asix) */
> - MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0
> - >;
> - };
> -
> - pinctrl_wifi_npd: wifinpd {
> - fsl,pins = <
> - /* WL_REG_ON */
> - MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x13069
> - >;
> - };
> -
> - pinctrl_usdhc2: usdhc2grp {
> - fsl,pins = <
> - MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
> - MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
> - MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
> - MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
> - MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
> - MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
> - >;
> - };
> -
> - pinctrl_audmux: audmuxgrp {
> - fsl,pins = <
> - MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
> - MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
> - MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
> - >;
> - };
> -
> - pinctrl_i2c2: i2c2grp {
> - fsl,pins = <
> - MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001f8b1
> - MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001f8b1
> - >;
> - };
> -
> - pinctrl_leds: ledsgrp {
> - /* No leds */
> - fsl,pins = <>;
> - };
> -
> - pinctrl_ecspi3: ecspi3grp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
> - MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
> - MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
> - /* CS */
> - MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
> - /* CAN2_nINT */
> - MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
> - >;
> - };
>
> - pinctrl_pwm1: pwm1grp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
> - >;
> - };
> +#include <arm/imx6qp-prtwd3.dts>
> +#include "imx6qdl-prti6q-emmc.dtsi"
>
> - pinctrl_pwm2: pwm2grp {
> - fsl,pins = <
> - MX6QDL_PAD_DISP0_DAT9__PWM2_OUT 0x1b0b0
> - >;
> - };
> -};
> diff --git a/arch/arm/dts/imx6qp-vicutp.dts b/arch/arm/dts/imx6qp-vicutp.dts
> index 44cfe68867..1411071fb3 100644
> --- a/arch/arm/dts/imx6qp-vicutp.dts
> +++ b/arch/arm/dts/imx6qp-vicutp.dts
> @@ -1,52 +1,5 @@
> // SPDX-License-Identifier: GPL-2.0-or-later
> -/*
> - * Copyright (c) 2014 Protonic Holland
> - */
> -
> /dts-v1/;
> -#include <arm/imx6qp.dtsi>
> -#include "imx6qdl-vicut1.dtsi"
> -
> -/ {
> - model = "Kverneland UT1P Board";
> - compatible = "kvg,vicutp", "fsl,imx6qp";
> -
> - memory {
> - reg = <0x10000000 0x80000000>;
> - };
> -};
> -
> -&fec {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_enet>;
> - phy-mode = "rgmii";
> - /* phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; */
> - status = "okay";
> -};
> -
> -&iomuxc {
> - pinctrl_enet: enetgrp {
> - fsl,pins = <
> - /* MX6QDL_ENET_PINGRP_RGMII_MD(0x1b030, 0x10030) */
> - MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
> - MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
> - MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
> - MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
> - MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
> - MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
> - MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
> - MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
> - MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
> - MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
> - MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
> - MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
> - MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
> - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
> - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
>
> - /* Phy reset */
> - MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
> - MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
> - >;
> - };
> -};
> +#include <arm/imx6qp-vicutp.dts>
> +#include "imx6qdl-prti6q-nor.dtsi"
> diff --git a/arch/arm/dts/imx6ul-prti6g.dts b/arch/arm/dts/imx6ul-prti6g.dts
> index e65198bab2..f720a2518c 100644
> --- a/arch/arm/dts/imx6ul-prti6g.dts
> +++ b/arch/arm/dts/imx6ul-prti6g.dts
> @@ -1,81 +1,64 @@
> -/*
> - * Copyright (C) 2016 Protonic Holland
> - *
> - * This program is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of
> - * the License, or (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - */
> -
> +// SPDX-License-Identifier: GPL-2.0-or-later
> /dts-v1/;
>
> -#include "imx6ul-prti6g.dtsi"
> +#include <arm/imx6ul-prti6g.dts>
>
> / {
> - model = "Protonic PRTI6G Board";
> - compatible = "prt,prti6g", "fsl,imx6ul";
> -};
> + chosen {
> + stdout-path = &uart4;
>
> -&pinctrl_hog {
> - fsl,pins = <
> - /* HW revision detect */
> - MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
> - MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
> - MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
> - MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
> - MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0 /* BOARD_ID0 */
> - MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x1b0b0 /* BOARD_ID1 */
> - MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 /* BOARD_ID2 */
> - MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x1b0b0 /* BOARD_ID3 */
> + environment@0 {
> + compatible = "barebox,environment";
> + device-path = &usdhc2, "partname:barebox-environment";
> + };
> + };
>
> - /* Safety controller IO */
> - MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0 /* WAKE_SC */
> - MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0 /* PROGRAM_SC */
> - >;
> -};
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
>
> -&ecspi2 {
> - status = "okay";
> -};
> + /* Address will be determined by the bootloader */
> + ramoops {
> + compatible = "ramoops";
> + };
> + };
>
> -&can2 {
> - status = "okay";
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + /* Address will be determined by the bootloader */
> + ramoops {
> + compatible = "ramoops";
> + };
> + };
> };
>
> -&i2c2 {
> - can_adc: ads1015@49 {
> - compatible = "ti,ads1015";
> - reg = <0x49>;
> +&ecspi1 {
> + flash@0 {
> #address-cells = <1>;
> - #size-cells = <0>;
> + #size-cells = <1>;
>
> - channel@4 {
> - reg = <4>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> + partition@0 {
> + label = "barebox";
> + reg = <0x0 0x100000>;
> };
> + };
> +};
>
> - channel@5 {
> - reg = <5>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> +&usdhc2 {
> + #address-cells = <1>;
> + #size-cells = <1>;
>
> - channel@6 {
> - reg = <6>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> + partition@40000 {
> + label = "barebox-environment";
> + reg = <0x40000 0x80000>;
> + };
>
> - channel@7 {
> - reg = <7>;
> - ti,gain = <3>;
> - ti,datarate = <3>;
> - };
> + partition@c0000 {
> + label = "state";
> + reg = <0xc0000 0x40000>;
> };
> };
> diff --git a/arch/arm/dts/imx6ul-prti6g.dtsi b/arch/arm/dts/imx6ul-prti6g.dtsi
> deleted file mode 100644
> index c20bbd5bc2..0000000000
> --- a/arch/arm/dts/imx6ul-prti6g.dtsi
> +++ /dev/null
> @@ -1,330 +0,0 @@
> -/*
> - * Copyright (C) 2016 Protonic Holland
> - *
> - * This program is free software; you can redistribute it and/or
> - * modify it under the terms of the GNU General Public License as
> - * published by the Free Software Foundation; either version 2 of
> - * the License, or (at your option) any later version.
> - *
> - * This program is distributed in the hope that it will be useful,
> - * but WITHOUT ANY WARRANTY; without even the implied warranty of
> - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> - * GNU General Public License for more details.
> - */
> -
> -#include <arm/imx6ul.dtsi>
> -#include <dt-bindings/gpio/gpio.h>
> -
> -/ {
> - chosen {
> - stdout-path = &uart1;
> - environment@0 {
> - compatible = "barebox,environment";
> - device-path = &flash, "partname:env";
> - };
> - };
> -
> - memory {
> - reg = <0x80000000 0x10000000>;
> - };
> -
> - regulators {
> - compatible = "simple-bus";
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - reg_3p2v: 3p2-regulator {
> - compatible = "regulator-fixed";
> - regulator-name = "regulator-3P2V";
> - regulator-min-microvolt = <3200000>;
> - regulator-max-microvolt = <3200000>;
> - regulator-always-on;
> - };
> -
> - reg_1p35v: 1p35-regulator {
> - compatible = "regulator-fixed";
> - regulator-name = "regulator-1P35V";
> - regulator-min-microvolt = <1350000>;
> - regulator-max-microvolt = <1350000>;
> - regulator-always-on;
> - };
> - };
> -
> - leds: leds {
> - compatible = "gpio-leds";
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_leds>;
> -
> - debug {
> - label = "debug0";
> - gpios = <&gpio4 16 0>;
> - linux,default-trigger = "heartbeat";
> - };
> - };
> -};
> -
> -&usbotg1 {
> - dr_mode = "host";
> - status = "okay";
> -};
> -
> -&uart1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_uart1>;
> - status = "okay";
> -};
> -
> -&usdhc1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc1>;
> - cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
> - vmmc-supply = <®_3p2v>;
> - wakeup-source;
> - status = "okay";
> -};
> -
> -&usdhc2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_usdhc2>;
> - bus-width = <8>;
> - non-removable;
> - status = "okay";
> -};
> -
> -&ecspi1 {
> - fsl,spi-num-chipselects = <1>;
> - cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi1>;
> - status = "okay";
> -
> - flash: w25q64fv@0 {
> - compatible = "winbond,w25q64", "jedec,spi-nor";
> - spi-max-frequency = <20000000>;
> - m25p,fast-read;
> - reg = <0>;
> -
> - #address-cells = <1>;
> - #size-cells = <1>;
> -
> - partition@0 {
> - label = "boot";
> - reg = <0x0 0x60000>; /* 384 Kb */
> - };
> -
> - partition@60000 {
> - label = "env";
> - reg = <0x60000 0x10000>; /* 64 Kb */
> - };
> -
> - partition@70000 {
> - label = "dtb";
> - reg = <0x70000 0x10000>; /* 64 Kb */
> - };
> -
> - partition@80000 {
> - label = "kernel";
> - reg = <0x80000 0x780000>; /* 7680 Kb */
> - };
> - };
> -};
> -
> -&ecspi2 {
> - fsl,spi-num-chipselects = <1>;
> - cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_ecspi2>;
> -};
> -
> -&i2c1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c1>;
> - clock-frequency = <100000>;
> - status = "okay";
> -
> - /* RFID chip */
> -};
> -
> -&i2c2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_i2c2>;
> - clock-frequency = <100000>;
> - status = "okay";
> -
> - rtc: pcf8563@51 {
> - compatible = "nxp,pcf8563";
> - reg = <0x51>;
> - };
> -
> - tmp103: tmp103@70 {
> - compatible = "ti,tmp103", "tmp103";
> - reg = <0x70>;
> - };
> -};
> -
> -&fec1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_fec1 &pinctrl_ethphy0_rst>;
> - phy-mode = "rmii";
> - phy-handle = <ðphy0>;
> - phy-reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
> - phy-reset-duration = <11>;
> - status = "okay";
> -
> - mdio {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - ethphy0: ethernet-phy@0 {
> - reg = <0>;
> - };
> - };
> -};
> -
> -
> -&can1 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_flexcan1>;
> - status = "okay";
> -};
> -
> -&can2 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_flexcan2>;
> -};
> -
> -&iomuxc {
> - pinctrl-names = "default";
> - pinctrl-0 = <&pinctrl_hog>;
> -
> - prti6g {
> - pinctrl_hog: hoggrp {
> - fsl,pins = <
> - /* HW revision detect */
> - MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x1b0b0 /* REV_ID0 */
> - MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x1b0b0 /* REV_ID1 */
> - MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x1b0b0 /* REV_ID2 */
> - MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x1b0b0 /* REV_ID3 */
> - MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0 /* BOARD_ID0 */
> - MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x1b0b0 /* BOARD_ID1 */
> - MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 /* BOARD_ID2 */
> - MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x1b0b0 /* BOARD_ID3 */
> -
> - /* CAN diagnostics (nSMBALERT) */
> - MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0
> - >;
> - };
> -
> - pinctrl_leds: ledsgrp {
> - fsl,pins = <
> - MX6UL_PAD_NAND_DQS__GPIO4_IO16 0x1b0b0
> - >;
> - };
> -
> - pinctrl_uart1: uart1grp {
> - fsl,pins = <
> - MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
> - MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
> - >;
> - };
> -
> - pinctrl_usdhc1: usdhc1grp {
> - fsl,pins = <
> - MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1
> - MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099
> - MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1
> - MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1
> - MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1
> - MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1
> - MX6UL_PAD_NAND_READY_B__GPIO4_IO12 0x170b0 /* SD1 CD */
> - >;
> - };
> -
> - pinctrl_usdhc2: usdhc2grp {
> - fsl,pins = <
> - MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
> - MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
> - MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
> - MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
> - MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
> - MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
> - MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9
> - MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9
> - MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9
> - MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9
> - MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0
> - >;
> - };
> -
> - pinctrl_ecspi1: ecspi1grp {
> - fsl,pins = <
> - MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x0b0b0
> - MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x000b1
> - MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x0b0b0
> - MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x0b0b0
> - >;
> - };
> -
> - pinctrl_ecspi2: ecspi2grp {
> - fsl,pins = <
> - MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x0b0b0
> - MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x000b1
> - MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x0b0b0
> - MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x0b0b0
> - >;
> - };
> -
> - pinctrl_i2c1: i2c1grp {
> - fsl,pins = <
> - MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
> - MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
> - >;
> - };
> -
> - pinctrl_i2c2: i2c2grp {
> - fsl,pins = <
> - MX6UL_PAD_CSI_VSYNC__I2C2_SDA 0x4001b8b0
> - MX6UL_PAD_CSI_HSYNC__I2C2_SCL 0x4001b8b0
> - >;
> - };
> -
> - pinctrl_fec1: fec1grp {
> - fsl,pins = <
> - MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
> - MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x100b0
> - MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
> - MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
> - MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x100b0
> - MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
> - MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
> - MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
> - MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
> - MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
> - >;
> - };
> -
> - pinctrl_ethphy0_rst: ethphy-rstgrp-0 {
> - fsl,pins = <
> - MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x00880 /* PHY RESET */
> - >;
> - };
> -
> - pinctrl_flexcan1: flexcan1grp {
> - fsl,pins = <
> - MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0
> - MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0
> - MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x0b0b0 /* SR */
> - MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 /* TERM */
> - MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x0b0b0 /* nSMBALERT */
> - >;
> - };
> -
> - pinctrl_flexcan2: flexcan2grp {
> - fsl,pins = <
> - MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x0b0b0
> - MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x0b0b0
> - MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 /* SR */
> - >;
> - };
> - };
> -};
> --
> 2.29.2
>
>
> _______________________________________________
> barebox mailing list
> barebox@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
