On 6/29/20 6:03 PM, Giorgio Dal Molin wrote:
> Hi,
>
>> On June 29, 2020 at 5:35 PM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> wrote:
>>
>>
>> Hello Giorgio,
>>
>> On 6/29/20 5:30 PM, Giorgio Dal Molin wrote:
>>> Hi,
>>>
>>>> On June 29, 2020 at 3:30 PM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> wrote:
>>>>
>>>>
>>>> Hello,
>>>>
>>>> On 6/29/20 12:53 PM, Giorgio Dal Molin wrote:
>>>>> Hi,
>>>>>
>>>>>> On June 29, 2020 at 10:44 AM Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx> wrote:
>>>>>>
>>>>>>
>>>>>> Hello Giorgio,
>>>>>>
>>>>>> On 6/23/20 5:11 PM, Giorgio Dal Molin wrote:
>>>>>>> Hi Fabio,
>>>>>>>
>>>>>>> thank you for your quick reply.
>>>>>>>
>>>>>>> I've already found the errata you linked in your mail but I had no success
>>>>>>> applying the suggestion there; maybe I'm doing it wrong.
>>>>>>> Let's take the Option 3 there:
>>>>>>
>>>>>> Does reset within Linux (with say the imx_v6_v7_defconfg) work?
>>>>>
>>>>> No. I see the same behavior also with the kernel: after a 'shutdown -r'
>>>>> the system 'goes down' but doesn't reboot, it just hang:
>>>>>
>>>>> ~ # shutdown -r
>>>>> system is going down for reboot NOW
>>>>> ...
>>>>> [ 46.248222] 000: ci_hdrc ci_hdrc.0: remove, state 1
>>>>> [ 46.248253] 000: usb usb1: USB disconnect, device number 1
>>>>> [ 46.248263] 000: usb 1-1: USB disconnect, device number 2
>>>>>
>>>>>
>>>>> The same happens if I kill the 'watchdog' process: after ~2 seconds
>>>>> the system just hangs.
>>>>>
>>>>> I'm sure there must be a solution because the original u-boot bootloader
>>>>> for the cpu module I'm using reboots the system as expected, through the wdog1;
>>>>> unfortunately it's not so trivial to find what makes the difference.
>>>>
>>>> Linux probably attempts reset via PSCI. Check for psci_system_reset
>>>> in your vendor's U-Boot and transplant it into barebox.
>>>
>>> U-Boot has actually a psci_system_reset(), it also rely on wdog1:
>>>
>>> __secure void psci_system_reset(void)
>>> {
>>> struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
>>>
>>> /* make sure WDOG1 clock is enabled */
>>> writel(0x1 << 28, CCM_BASE_ADDR + CCM_ROOT_WDOG);
>>> writel(0x3, CCM_BASE_ADDR + CCM_CCGR_WDOG1);
>>> writew(WCR_WDE, &wdog->wcr);
>>>
>>> while (1)
>>> wfi();
>>> }
>>>
>>> It is also compiled in the uboot image, because if I add a syntax error in
>>> its body the compiler tells me; anyway I think it's not called when I issue
>>> the 'reset' command at the prompt because the 'reset' works properly even if
>>> I comment out the whole body of the function or if I add an endless loop like
>>> while(1); to it.
>>
>> Yes. It should be called by the kernel when CONFIG_ARM_PSCI_FW=y
>> and the device tree has the correct node.
>>> Anyway I ported it to barebox, defining a void psci_system_reset(void) in
>>> arch/arm/mach-imx/imx7.c:
>>>
>>> ...
>>> #define CCM_BASE_ADDR 0x30380000
>>> #define CCM_ROOT_WDOG 0xbb80
>>> #define CCM_CCGR_WDOG1 0x49c8
>>> #define WCR_WDE 0x04
>>> #define WDOG1_WCR 0x30280000
>>> #define wfi() __asm__ __volatile__ ("wfi" : : : "memory")
>>>
>>> static void imx7_system_reset(void)
>>> {
>>> printf("%s: called now.\n",__func__);
>>>
>>> // make sure WDOG1 clock is enabled
>>> writel(0x1 << 28, CCM_BASE_ADDR + CCM_ROOT_WDOG);
>>> writel(0x3, CCM_BASE_ADDR + CCM_CCGR_WDOG1);
>>> writew(WCR_WDE, WDOG1_WCR);
>>>
>>> while (1)
>>> wfi();
>>> };
>>>
>>> static struct psci_ops imx7_psci_ops = {
>>> .cpu_on = imx7_cpu_on,
>>> .cpu_off = imx7_cpu_off,
>>> .system_reset = imx7_system_reset,
>>> };
>>>
>>> and the following case to smc.c:
>>>
>>> static int do_smc(int argc, char *argv[])
>>> {
>>> ...
>>> case 'r':
>>> printf("issue psci reset...\n");
>>> arm_smccc_smc(ARM_PSCI_0_2_FN_SYSTEM_RESET,
>>> 0, 0, 0, 0, 0, 0, 0, &res);
>>> printf("reset issued...\n");
>>> break;
>>> ...
>>>
>>> to be able to call it.
>>> Now, using the modified 'smc' command I can see my printf's:
>>>
>>> samx7: / smc -n
>>> samx7: / smc -r
>>> issue psci reset...
>>> psci_system_reset called.
>>> imx7_system_reset: called now.
>>>
>>> but the soc still just hangs.
>>
>> What does U-Boot's reset commando do on an i.MX7?
>
> It ends up calling this function in the imx_watchdog.c:
>
> void __attribute__((weak)) reset_cpu(ulong addr)
> {
> struct watchdog_regs *wdog = (struct watchdog_regs *)WDOG1_BASE_ADDR;
>
> printf("%s: called now\n",__func__);
> udelay(500);
>
> clrsetbits_le16(&wdog->wcr, WCR_WT_MSK, WCR_WDE);
>
> writew(0x5555, &wdog->wsr);
> writew(0xaaaa, &wdog->wsr); /* load minimum 1/2 second timeout */
> while (1) {
> /*
> * spin for .5 seconds before reset
> */
> }
> }
>
> I added the printf / udelay to be sure. WCR_WT_MSK is (0xff << 8).
Hmm and same code doesn't reset it in barebox? That's strange.
Is there something in the DCD table that you are missing in barebox?
>
> What I also observed is that if I upload the uboot image with the imx-usb-loader it boots
> and runs normally but the reset in this case also just hangs the soc without rebooting it,
> like barebox; so there must be a difference between an 'usb uploaded' boot and a 'qspi native'
> boot.
Are you sure it's not resetting to serial download mode again?
>
> giorgio
>
>>
>>>
>>> giorgio
>>>
>>>>
>>>>>
>>>>> giorgio
>>>>>
>>>>>
>>>>>>
>>>>>> --
>>>>>> Pengutronix e.K. | |
>>>>>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
>>>>>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
>>>>>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>>>>>>
>>>>>> _______________________________________________
>>>>>> barebox mailing list
>>>>>> barebox@xxxxxxxxxxxxxxxxxxx
>>>>>> http://lists.infradead.org/mailman/listinfo/barebox
>>>>>
>>>>
>>>> --
>>>> Pengutronix e.K. | |
>>>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
>>>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
>>>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>>>>
>>>> _______________________________________________
>>>> barebox mailing list
>>>> barebox@xxxxxxxxxxxxxxxxxxx
>>>> http://lists.infradead.org/mailman/listinfo/barebox
>>>
>>
>> --
>> Pengutronix e.K. | |
>> Steuerwalder Str. 21 | http://www.pengutronix.de/ |
>> 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
>> Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
>>
>> _______________________________________________
>> barebox mailing list
>> barebox@xxxxxxxxxxxxxxxxxxx
>> http://lists.infradead.org/mailman/listinfo/barebox
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
