Port Microchip USB251x USB hub driver from Linux. Needed by ZII's i.MX8MQ boards. Signed-off-by: Andrey Smirnov <andrew.smirnov@xxxxxxxxx> --- drivers/usb/Kconfig | 2 + drivers/usb/Makefile | 1 + drivers/usb/misc/Kconfig | 14 + drivers/usb/misc/Makefile | 6 + drivers/usb/misc/usb251xb.c | 672 ++++++++++++++++++++++++++++++++++++ 5 files changed, 695 insertions(+) create mode 100644 drivers/usb/misc/Kconfig create mode 100644 drivers/usb/misc/Makefile create mode 100644 drivers/usb/misc/usb251xb.c diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig index ee33e0f28..8ff3d18d4 100644 --- a/drivers/usb/Kconfig +++ b/drivers/usb/Kconfig @@ -17,6 +17,8 @@ source drivers/usb/otg/Kconfig source drivers/usb/storage/Kconfig +source "drivers/usb/misc/Kconfig" + endif source drivers/usb/gadget/Kconfig diff --git a/drivers/usb/Makefile b/drivers/usb/Makefile index 13fca2cbd..9e9809950 100644 --- a/drivers/usb/Makefile +++ b/drivers/usb/Makefile @@ -6,4 +6,5 @@ obj-$(CONFIG_USB_GADGET) += gadget/ obj-$(CONFIG_USB_STORAGE) += storage/ obj-y += host/ obj-y += otg/ +obj-$(CONFIG_USB) += misc/ diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig new file mode 100644 index 000000000..7d6c9da59 --- /dev/null +++ b/drivers/usb/misc/Kconfig @@ -0,0 +1,14 @@ +# +# USB Miscellaneous driver configuration +# +comment "USB Miscellaneous drivers" + +config USB_HUB_USB251XB + bool "USB251XB Hub Controller Configuration Driver" + depends on I2C + select NLS + help + This option enables support for configuration via SMBus of the + Microchip USB251x/xBi USB 2.0 Hub Controller series. Configuration + parameters may be set in devicetree or platform data. + Say Y or M here if you need to configure such a device via SMBus. diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile new file mode 100644 index 000000000..fb69c454b --- /dev/null +++ b/drivers/usb/misc/Makefile @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0 +# +# Makefile for the rest of the USB drivers +# (the ones that don't fit into any other categories) +# +obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o diff --git a/drivers/usb/misc/usb251xb.c b/drivers/usb/misc/usb251xb.c new file mode 100644 index 000000000..0b721f6d4 --- /dev/null +++ b/drivers/usb/misc/usb251xb.c @@ -0,0 +1,672 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Driver for Microchip USB251xB USB 2.0 Hi-Speed Hub Controller + * Configuration via SMBus. + * + * Copyright (c) 2017 SKIDATA AG + * + * This work is based on the USB3503 driver by Dongjin Kim and + * a not-accepted patch by Fabien Lahoudere, see: + * https://patchwork.kernel.org/patch/9257715/ + */ + +#include <common.h> +#include <init.h> +#include <driver.h> +#include <i2c/i2c.h> +#include <of.h> +#include <gpio.h> +#include <of_gpio.h> +#include <of_device.h> + +#include <linux/nls.h> + +/* Internal Register Set Addresses & Default Values acc. to DS00001692C */ +#define USB251XB_ADDR_VENDOR_ID_LSB 0x00 +#define USB251XB_ADDR_VENDOR_ID_MSB 0x01 +#define USB251XB_DEF_VENDOR_ID 0x0424 + +#define USB251XB_ADDR_PRODUCT_ID_LSB 0x02 +#define USB251XB_ADDR_PRODUCT_ID_MSB 0x03 +#define USB251XB_DEF_PRODUCT_ID_12 0x2512 /* USB2512B/12Bi */ +#define USB251XB_DEF_PRODUCT_ID_13 0x2513 /* USB2513B/13Bi */ +#define USB251XB_DEF_PRODUCT_ID_14 0x2514 /* USB2514B/14Bi */ +#define USB251XB_DEF_PRODUCT_ID_17 0x2517 /* USB2517/17i */ + +#define USB251XB_ADDR_DEVICE_ID_LSB 0x04 +#define USB251XB_ADDR_DEVICE_ID_MSB 0x05 +#define USB251XB_DEF_DEVICE_ID 0x0BB3 + +#define USB251XB_ADDR_CONFIG_DATA_1 0x06 +#define USB251XB_DEF_CONFIG_DATA_1 0x9B +#define USB251XB_ADDR_CONFIG_DATA_2 0x07 +#define USB251XB_DEF_CONFIG_DATA_2 0x20 +#define USB251XB_ADDR_CONFIG_DATA_3 0x08 +#define USB251XB_DEF_CONFIG_DATA_3 0x02 + +#define USB251XB_ADDR_NON_REMOVABLE_DEVICES 0x09 +#define USB251XB_DEF_NON_REMOVABLE_DEVICES 0x00 + +#define USB251XB_ADDR_PORT_DISABLE_SELF 0x0A +#define USB251XB_DEF_PORT_DISABLE_SELF 0x00 +#define USB251XB_ADDR_PORT_DISABLE_BUS 0x0B +#define USB251XB_DEF_PORT_DISABLE_BUS 0x00 + +#define USB251XB_ADDR_MAX_POWER_SELF 0x0C +#define USB251XB_DEF_MAX_POWER_SELF 0x01 +#define USB251XB_ADDR_MAX_POWER_BUS 0x0D +#define USB251XB_DEF_MAX_POWER_BUS 0x32 + +#define USB251XB_ADDR_MAX_CURRENT_SELF 0x0E +#define USB251XB_DEF_MAX_CURRENT_SELF 0x01 +#define USB251XB_ADDR_MAX_CURRENT_BUS 0x0F +#define USB251XB_DEF_MAX_CURRENT_BUS 0x32 + +#define USB251XB_ADDR_POWER_ON_TIME 0x10 +#define USB251XB_DEF_POWER_ON_TIME 0x32 + +#define USB251XB_ADDR_LANGUAGE_ID_HIGH 0x11 +#define USB251XB_ADDR_LANGUAGE_ID_LOW 0x12 +#define USB251XB_DEF_LANGUAGE_ID 0x0000 + +#define USB251XB_STRING_BUFSIZE 62 +#define USB251XB_ADDR_MANUFACTURER_STRING_LEN 0x13 +#define USB251XB_ADDR_MANUFACTURER_STRING 0x16 +#define USB251XB_DEF_MANUFACTURER_STRING "Microchip" + +#define USB251XB_ADDR_PRODUCT_STRING_LEN 0x14 +#define USB251XB_ADDR_PRODUCT_STRING 0x54 +#define USB251XB_DEF_PRODUCT_STRING "USB251xB/xBi/7i" + +#define USB251XB_ADDR_SERIAL_STRING_LEN 0x15 +#define USB251XB_ADDR_SERIAL_STRING 0x92 +#define USB251XB_DEF_SERIAL_STRING "" + +#define USB251XB_ADDR_BATTERY_CHARGING_ENABLE 0xD0 +#define USB251XB_DEF_BATTERY_CHARGING_ENABLE 0x00 + +#define USB251XB_ADDR_BOOST_UP 0xF6 +#define USB251XB_DEF_BOOST_UP 0x00 +#define USB251XB_ADDR_BOOST_57 0xF7 +#define USB251XB_DEF_BOOST_57 0x00 +#define USB251XB_ADDR_BOOST_14 0xF8 +#define USB251XB_DEF_BOOST_14 0x00 + +#define USB251XB_ADDR_PORT_SWAP 0xFA +#define USB251XB_DEF_PORT_SWAP 0x00 + +#define USB251XB_ADDR_PORT_MAP_12 0xFB +#define USB251XB_DEF_PORT_MAP_12 0x00 +#define USB251XB_ADDR_PORT_MAP_34 0xFC +#define USB251XB_DEF_PORT_MAP_34 0x00 /* USB251{3B/i,4B/i,7/i} only */ +#define USB251XB_ADDR_PORT_MAP_56 0xFD +#define USB251XB_DEF_PORT_MAP_56 0x00 /* USB2517/i only */ +#define USB251XB_ADDR_PORT_MAP_7 0xFE +#define USB251XB_DEF_PORT_MAP_7 0x00 /* USB2517/i only */ + +#define USB251XB_ADDR_STATUS_COMMAND 0xFF +#define USB251XB_STATUS_COMMAND_SMBUS_DOWN 0x04 +#define USB251XB_STATUS_COMMAND_RESET 0x02 +#define USB251XB_STATUS_COMMAND_ATTACH 0x01 + +#define USB251XB_I2C_REG_SZ 0x100 +#define USB251XB_I2C_WRITE_SZ 0x10 + +#define DRIVER_NAME "usb251xb" +#define DRIVER_DESC "Microchip USB 2.0 Hi-Speed Hub Controller" + +struct usb251xb { + struct device_d *dev; + struct i2c_client *i2c; + u8 skip_config; + int gpio_reset; + u16 vendor_id; + u16 product_id; + u16 device_id; + u8 conf_data1; + u8 conf_data2; + u8 conf_data3; + u8 non_rem_dev; + u8 port_disable_sp; + u8 port_disable_bp; + u8 max_power_sp; + u8 max_power_bp; + u8 max_current_sp; + u8 max_current_bp; + u8 power_on_time; + u16 lang_id; + u8 manufacturer_len; + u8 product_len; + u8 serial_len; + char manufacturer[USB251XB_STRING_BUFSIZE]; + char product[USB251XB_STRING_BUFSIZE]; + char serial[USB251XB_STRING_BUFSIZE]; + u8 bat_charge_en; + u8 boost_up; + u8 boost_57; + u8 boost_14; + u8 port_swap; + u8 port_map12; + u8 port_map34; + u8 port_map56; + u8 port_map7; + u8 status; +}; + +struct usb251xb_data { + u16 product_id; + u8 port_cnt; + bool led_support; + bool bat_support; + char product_str[USB251XB_STRING_BUFSIZE / 2]; /* ASCII string */ +}; + +static const struct usb251xb_data usb2512b_data = { + .product_id = 0x2512, + .port_cnt = 2, + .led_support = false, + .bat_support = true, + .product_str = "USB2512B", +}; + +static const struct usb251xb_data usb2512bi_data = { + .product_id = 0x2512, + .port_cnt = 2, + .led_support = false, + .bat_support = true, + .product_str = "USB2512Bi", +}; + +static const struct usb251xb_data usb2513b_data = { + .product_id = 0x2513, + .port_cnt = 3, + .led_support = false, + .bat_support = true, + .product_str = "USB2513B", +}; + +static const struct usb251xb_data usb2513bi_data = { + .product_id = 0x2513, + .port_cnt = 3, + .led_support = false, + .bat_support = true, + .product_str = "USB2513Bi", +}; + +static const struct usb251xb_data usb2514b_data = { + .product_id = 0x2514, + .port_cnt = 4, + .led_support = false, + .bat_support = true, + .product_str = "USB2514B", +}; + +static const struct usb251xb_data usb2514bi_data = { + .product_id = 0x2514, + .port_cnt = 4, + .led_support = false, + .bat_support = true, + .product_str = "USB2514Bi", +}; + +static const struct usb251xb_data usb2517_data = { + .product_id = 0x2517, + .port_cnt = 7, + .led_support = true, + .bat_support = false, + .product_str = "USB2517", +}; + +static const struct usb251xb_data usb2517i_data = { + .product_id = 0x2517, + .port_cnt = 7, + .led_support = true, + .bat_support = false, + .product_str = "USB2517i", +}; + +static void usb251xb_reset(struct usb251xb *hub, int state) +{ + if (!gpio_is_valid(hub->gpio_reset)) + return; + + gpio_set_active(hub->gpio_reset, state); + + /* wait for hub recovery/stabilization */ + if (!state) + udelay(750); /* >=500us at power on */ + else + udelay(10); /* >=1us at power down */ +} + +static int usb251xb_connect(struct usb251xb *hub) +{ + struct device_d *dev = hub->dev; + int err, i; + char i2c_wb[USB251XB_I2C_REG_SZ]; + + memset(i2c_wb, 0, USB251XB_I2C_REG_SZ); + + if (hub->skip_config) { + dev_info(dev, "Skip hub configuration, only attach.\n"); + i2c_wb[0] = 0x01; + i2c_wb[1] = USB251XB_STATUS_COMMAND_ATTACH; + + usb251xb_reset(hub, 0); + + err = i2c_smbus_write_i2c_block_data(hub->i2c, + USB251XB_ADDR_STATUS_COMMAND, 2, i2c_wb); + if (err) { + dev_err(dev, "attaching hub failed: %d\n", err); + return err; + } + return 0; + } + + i2c_wb[USB251XB_ADDR_VENDOR_ID_MSB] = (hub->vendor_id >> 8) & 0xFF; + i2c_wb[USB251XB_ADDR_VENDOR_ID_LSB] = hub->vendor_id & 0xFF; + i2c_wb[USB251XB_ADDR_PRODUCT_ID_MSB] = (hub->product_id >> 8) & 0xFF; + i2c_wb[USB251XB_ADDR_PRODUCT_ID_LSB] = hub->product_id & 0xFF; + i2c_wb[USB251XB_ADDR_DEVICE_ID_MSB] = (hub->device_id >> 8) & 0xFF; + i2c_wb[USB251XB_ADDR_DEVICE_ID_LSB] = hub->device_id & 0xFF; + i2c_wb[USB251XB_ADDR_CONFIG_DATA_1] = hub->conf_data1; + i2c_wb[USB251XB_ADDR_CONFIG_DATA_2] = hub->conf_data2; + i2c_wb[USB251XB_ADDR_CONFIG_DATA_3] = hub->conf_data3; + i2c_wb[USB251XB_ADDR_NON_REMOVABLE_DEVICES] = hub->non_rem_dev; + i2c_wb[USB251XB_ADDR_PORT_DISABLE_SELF] = hub->port_disable_sp; + i2c_wb[USB251XB_ADDR_PORT_DISABLE_BUS] = hub->port_disable_bp; + i2c_wb[USB251XB_ADDR_MAX_POWER_SELF] = hub->max_power_sp; + i2c_wb[USB251XB_ADDR_MAX_POWER_BUS] = hub->max_power_bp; + i2c_wb[USB251XB_ADDR_MAX_CURRENT_SELF] = hub->max_current_sp; + i2c_wb[USB251XB_ADDR_MAX_CURRENT_BUS] = hub->max_current_bp; + i2c_wb[USB251XB_ADDR_POWER_ON_TIME] = hub->power_on_time; + i2c_wb[USB251XB_ADDR_LANGUAGE_ID_HIGH] = (hub->lang_id >> 8) & 0xFF; + i2c_wb[USB251XB_ADDR_LANGUAGE_ID_LOW] = hub->lang_id & 0xFF; + i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING_LEN] = hub->manufacturer_len; + i2c_wb[USB251XB_ADDR_PRODUCT_STRING_LEN] = hub->product_len; + i2c_wb[USB251XB_ADDR_SERIAL_STRING_LEN] = hub->serial_len; + memcpy(&i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING], hub->manufacturer, + USB251XB_STRING_BUFSIZE); + memcpy(&i2c_wb[USB251XB_ADDR_SERIAL_STRING], hub->serial, + USB251XB_STRING_BUFSIZE); + memcpy(&i2c_wb[USB251XB_ADDR_PRODUCT_STRING], hub->product, + USB251XB_STRING_BUFSIZE); + i2c_wb[USB251XB_ADDR_BATTERY_CHARGING_ENABLE] = hub->bat_charge_en; + i2c_wb[USB251XB_ADDR_BOOST_UP] = hub->boost_up; + i2c_wb[USB251XB_ADDR_BOOST_57] = hub->boost_57; + i2c_wb[USB251XB_ADDR_BOOST_14] = hub->boost_14; + i2c_wb[USB251XB_ADDR_PORT_SWAP] = hub->port_swap; + i2c_wb[USB251XB_ADDR_PORT_MAP_12] = hub->port_map12; + i2c_wb[USB251XB_ADDR_PORT_MAP_34] = hub->port_map34; + i2c_wb[USB251XB_ADDR_PORT_MAP_56] = hub->port_map56; + i2c_wb[USB251XB_ADDR_PORT_MAP_7] = hub->port_map7; + i2c_wb[USB251XB_ADDR_STATUS_COMMAND] = USB251XB_STATUS_COMMAND_ATTACH; + + usb251xb_reset(hub, 0); + + /* write registers */ + for (i = 0; i < (USB251XB_I2C_REG_SZ / USB251XB_I2C_WRITE_SZ); i++) { + int offset = i * USB251XB_I2C_WRITE_SZ; + char wbuf[USB251XB_I2C_WRITE_SZ + 1]; + + /* The first data byte transferred tells the hub how many data + * bytes will follow (byte count). + */ + wbuf[0] = USB251XB_I2C_WRITE_SZ; + memcpy(&wbuf[1], &i2c_wb[offset], USB251XB_I2C_WRITE_SZ); + + dev_dbg(dev, "writing %d byte block %d to 0x%02X\n", + USB251XB_I2C_WRITE_SZ, i, offset); + + err = i2c_smbus_write_i2c_block_data(hub->i2c, offset, + USB251XB_I2C_WRITE_SZ + 1, + wbuf); + if (err) + goto out_err; + } + + dev_info(dev, "Hub configuration was successful.\n"); + return 0; + +out_err: + dev_err(dev, "configuring block %d failed: %d\n", i, err); + return err; +} + +#ifdef CONFIG_OFDEVICE +static int usb251xb_get_ofdata(struct usb251xb *hub, + struct usb251xb_data *data) +{ + struct device_d *dev = hub->dev; + struct device_node *np = dev->device_node; + int len, err, i; + u32 property_u32 = 0; + const u32 *cproperty_u32; + const char *cproperty_char; + enum of_gpio_flags of_flags; + unsigned long flags = GPIOF_OUT_INIT_ACTIVE; + char str[USB251XB_STRING_BUFSIZE / 2]; + + if (!np) { + dev_err(dev, "failed to get ofdata\n"); + return -ENODEV; + } + + if (of_get_property(np, "skip-config", NULL)) + hub->skip_config = 1; + else + hub->skip_config = 0; + + hub->gpio_reset = of_get_named_gpio_flags(np, "reset-gpios", 0, + &of_flags); + if (gpio_is_valid(hub->gpio_reset)) { + char *name; + int ret; + + if (of_flags & OF_GPIO_ACTIVE_LOW) + flags |= GPIOF_ACTIVE_LOW; + + name = basprintf("%s reset", dev_name(dev)); + ret = gpio_request_one(hub->gpio_reset, flags, name); + if (ret < 0) + return ret; + } else if (hub->gpio_reset == -EPROBE_DEFER) { + return -EPROBE_DEFER; + } else { + err = hub->gpio_reset; + dev_err(dev, "unable to request GPIO reset pin (%d)\n", err); + return err; + } + + if (of_property_read_u16_array(np, "vendor-id", &hub->vendor_id, 1)) + hub->vendor_id = USB251XB_DEF_VENDOR_ID; + + if (of_property_read_u16_array(np, "product-id", + &hub->product_id, 1)) + hub->product_id = data->product_id; + + if (of_property_read_u16_array(np, "device-id", &hub->device_id, 1)) + hub->device_id = USB251XB_DEF_DEVICE_ID; + + hub->conf_data1 = USB251XB_DEF_CONFIG_DATA_1; + if (of_get_property(np, "self-powered", NULL)) { + hub->conf_data1 |= BIT(7); + + /* Configure Over-Current sens when self-powered */ + hub->conf_data1 &= ~BIT(2); + if (of_get_property(np, "ganged-sensing", NULL)) + hub->conf_data1 &= ~BIT(1); + else if (of_get_property(np, "individual-sensing", NULL)) + hub->conf_data1 |= BIT(1); + } else if (of_get_property(np, "bus-powered", NULL)) { + hub->conf_data1 &= ~BIT(7); + + /* Disable Over-Current sense when bus-powered */ + hub->conf_data1 |= BIT(2); + } + + if (of_get_property(np, "disable-hi-speed", NULL)) + hub->conf_data1 |= BIT(5); + + if (of_get_property(np, "multi-tt", NULL)) + hub->conf_data1 |= BIT(4); + else if (of_get_property(np, "single-tt", NULL)) + hub->conf_data1 &= ~BIT(4); + + if (of_get_property(np, "disable-eop", NULL)) + hub->conf_data1 |= BIT(3); + + if (of_get_property(np, "individual-port-switching", NULL)) + hub->conf_data1 |= BIT(0); + else if (of_get_property(np, "ganged-port-switching", NULL)) + hub->conf_data1 &= ~BIT(0); + + hub->conf_data2 = USB251XB_DEF_CONFIG_DATA_2; + if (of_get_property(np, "dynamic-power-switching", NULL)) + hub->conf_data2 |= BIT(7); + + if (!of_property_read_u32(np, "oc-delay-us", &property_u32)) { + if (property_u32 == 100) { + /* 100 us*/ + hub->conf_data2 &= ~BIT(5); + hub->conf_data2 &= ~BIT(4); + } else if (property_u32 == 4000) { + /* 4 ms */ + hub->conf_data2 &= ~BIT(5); + hub->conf_data2 |= BIT(4); + } else if (property_u32 == 16000) { + /* 16 ms */ + hub->conf_data2 |= BIT(5); + hub->conf_data2 |= BIT(4); + } else { + /* 8 ms (DEFAULT) */ + hub->conf_data2 |= BIT(5); + hub->conf_data2 &= ~BIT(4); + } + } + + if (of_get_property(np, "compound-device", NULL)) + hub->conf_data2 |= BIT(3); + + hub->conf_data3 = USB251XB_DEF_CONFIG_DATA_3; + if (of_get_property(np, "port-mapping-mode", NULL)) + hub->conf_data3 |= BIT(3); + + if (data->led_support && of_get_property(np, "led-usb-mode", NULL)) + hub->conf_data3 &= ~BIT(1); + + if (of_get_property(np, "string-support", NULL)) + hub->conf_data3 |= BIT(0); + + hub->non_rem_dev = USB251XB_DEF_NON_REMOVABLE_DEVICES; + cproperty_u32 = of_get_property(np, "non-removable-ports", &len); + if (cproperty_u32 && (len / sizeof(u32)) > 0) { + for (i = 0; i < len / sizeof(u32); i++) { + u32 port = be32_to_cpu(cproperty_u32[i]); + + if ((port >= 1) && (port <= data->port_cnt)) + hub->non_rem_dev |= BIT(port); + else + dev_warn(dev, "NRD port %u doesn't exist\n", + port); + } + } + + hub->port_disable_sp = USB251XB_DEF_PORT_DISABLE_SELF; + cproperty_u32 = of_get_property(np, "sp-disabled-ports", &len); + if (cproperty_u32 && (len / sizeof(u32)) > 0) { + for (i = 0; i < len / sizeof(u32); i++) { + u32 port = be32_to_cpu(cproperty_u32[i]); + + if ((port >= 1) && (port <= data->port_cnt)) + hub->port_disable_sp |= BIT(port); + else + dev_warn(dev, "PDS port %u doesn't exist\n", + port); + } + } + + hub->port_disable_bp = USB251XB_DEF_PORT_DISABLE_BUS; + cproperty_u32 = of_get_property(np, "bp-disabled-ports", &len); + if (cproperty_u32 && (len / sizeof(u32)) > 0) { + for (i = 0; i < len / sizeof(u32); i++) { + u32 port = be32_to_cpu(cproperty_u32[i]); + + if ((port >= 1) && (port <= data->port_cnt)) + hub->port_disable_bp |= BIT(port); + else + dev_warn(dev, "PDB port %u doesn't exist\n", + port); + } + } + + hub->max_power_sp = USB251XB_DEF_MAX_POWER_SELF; + if (!of_property_read_u32(np, "sp-max-total-current-microamp", + &property_u32)) + hub->max_power_sp = min_t(u8, property_u32 / 2000, 50); + + hub->max_power_bp = USB251XB_DEF_MAX_POWER_BUS; + if (!of_property_read_u32(np, "bp-max-total-current-microamp", + &property_u32)) + hub->max_power_bp = min_t(u8, property_u32 / 2000, 255); + + hub->max_current_sp = USB251XB_DEF_MAX_CURRENT_SELF; + if (!of_property_read_u32(np, "sp-max-removable-current-microamp", + &property_u32)) + hub->max_current_sp = min_t(u8, property_u32 / 2000, 50); + + hub->max_current_bp = USB251XB_DEF_MAX_CURRENT_BUS; + if (!of_property_read_u32(np, "bp-max-removable-current-microamp", + &property_u32)) + hub->max_current_bp = min_t(u8, property_u32 / 2000, 255); + + hub->power_on_time = USB251XB_DEF_POWER_ON_TIME; + if (!of_property_read_u32(np, "power-on-time-ms", &property_u32)) + hub->power_on_time = min_t(u8, property_u32 / 2, 255); + + if (of_property_read_u16_array(np, "language-id", &hub->lang_id, 1)) + hub->lang_id = USB251XB_DEF_LANGUAGE_ID; + + cproperty_char = of_get_property(np, "manufacturer", NULL); + strlcpy(str, cproperty_char ? : USB251XB_DEF_MANUFACTURER_STRING, + sizeof(str)); + hub->manufacturer_len = strlen(str) & 0xFF; + memset(hub->manufacturer, 0, USB251XB_STRING_BUFSIZE); + len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str)); + len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN, + (wchar_t *)hub->manufacturer, + USB251XB_STRING_BUFSIZE); + + cproperty_char = of_get_property(np, "product", NULL); + strlcpy(str, cproperty_char ? : data->product_str, sizeof(str)); + hub->product_len = strlen(str) & 0xFF; + memset(hub->product, 0, USB251XB_STRING_BUFSIZE); + len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str)); + len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN, + (wchar_t *)hub->product, + USB251XB_STRING_BUFSIZE); + + cproperty_char = of_get_property(np, "serial", NULL); + strlcpy(str, cproperty_char ? : USB251XB_DEF_SERIAL_STRING, + sizeof(str)); + hub->serial_len = strlen(str) & 0xFF; + memset(hub->serial, 0, USB251XB_STRING_BUFSIZE); + len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str)); + len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN, + (wchar_t *)hub->serial, + USB251XB_STRING_BUFSIZE); + + /* The following parameters are currently not exposed to devicetree, but + * may be as soon as needed. + */ + hub->bat_charge_en = USB251XB_DEF_BATTERY_CHARGING_ENABLE; + hub->boost_up = USB251XB_DEF_BOOST_UP; + hub->boost_57 = USB251XB_DEF_BOOST_57; + hub->boost_14 = USB251XB_DEF_BOOST_14; + hub->port_swap = USB251XB_DEF_PORT_SWAP; + hub->port_map12 = USB251XB_DEF_PORT_MAP_12; + hub->port_map34 = USB251XB_DEF_PORT_MAP_34; + hub->port_map56 = USB251XB_DEF_PORT_MAP_56; + hub->port_map7 = USB251XB_DEF_PORT_MAP_7; + + return 0; +} + +static const struct of_device_id usb251xb_of_match[] = { + { + .compatible = "microchip,usb2512b", + .data = &usb2512b_data, + }, { + .compatible = "microchip,usb2512bi", + .data = &usb2512bi_data, + }, { + .compatible = "microchip,usb2513b", + .data = &usb2513b_data, + }, { + .compatible = "microchip,usb2513bi", + .data = &usb2513bi_data, + }, { + .compatible = "microchip,usb2514b", + .data = &usb2514b_data, + }, { + .compatible = "microchip,usb2514bi", + .data = &usb2514bi_data, + }, { + .compatible = "microchip,usb2517", + .data = &usb2517_data, + }, { + .compatible = "microchip,usb2517i", + .data = &usb2517i_data, + }, { + /* sentinel */ + } +}; +#else /* CONFIG_OF */ +static int usb251xb_get_ofdata(struct usb251xb *hub, + struct usb251xb_data *data) +{ + return 0; +} +#endif /* CONFIG_OF */ + +static int usb251xb_probe(struct usb251xb *hub) +{ + struct device_d *dev = hub->dev; + struct device_node *np = dev->device_node; + const struct of_device_id *of_id = of_match_device(usb251xb_of_match, + dev); + int err; + + if (np) { + err = usb251xb_get_ofdata(hub, + (struct usb251xb_data *)of_id->data); + if (err) { + dev_err(dev, "failed to get ofdata: %d\n", err); + return err; + } + } + + err = usb251xb_connect(hub); + if (err) { + dev_err(dev, "Failed to connect hub (%d)\n", err); + return err; + } + + dev_info(dev, "Hub probed successfully\n"); + + return 0; +} + +static int usb251xb_i2c_probe(struct device_d *dev) +{ + struct i2c_client *i2c = to_i2c_client(dev); + struct usb251xb *hub; + + hub = xzalloc(sizeof(struct usb251xb)); + + i2c_set_clientdata(i2c, hub); + hub->dev = &i2c->dev; + hub->i2c = i2c; + + return usb251xb_probe(hub); +} + +static const struct platform_device_id usb251xb_id[] = { + { "usb2512b", 0 }, + { "usb2512bi", 0 }, + { "usb2513b", 0 }, + { "usb2513bi", 0 }, + { "usb2514b", 0 }, + { "usb2514bi", 0 }, + { "usb2517", 0 }, + { "usb2517i", 0 }, + { /* sentinel */ } +}; + +static struct driver_d usb251xb_i2c_driver = { + .name = DRIVER_NAME, + .probe = usb251xb_i2c_probe, + .id_table = usb251xb_id, + .of_compatible = DRV_OF_COMPAT(usb251xb_of_match), +}; +device_i2c_driver(usb251xb_i2c_driver); -- 2.20.1 _______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox
