Hi Roland, This one doesn't apply. Could you rebase? Sascha On Mon, Dec 10, 2018 at 04:55:09PM +0100, Roland Hieber wrote: > Signed-off-by: Roland Hieber <rhi@xxxxxxxxxxxxxx> > --- > Documentation/boards/imx.rst | 102 +++++++++++++++++++---------------- > 1 file changed, 57 insertions(+), 45 deletions(-) > > diff --git a/Documentation/boards/imx.rst b/Documentation/boards/imx.rst > index 35a180b0dd..2e6a30fd2f 100644 > --- a/Documentation/boards/imx.rst > +++ b/Documentation/boards/imx.rst > @@ -32,114 +32,126 @@ Normally it's not necessary to call this tool manually, it is executed > automatically at the end of the build process. > > The images generated by the build process can be directly written to an > SD card: > > .. code-block:: sh > > # with Multi Image support: > cat images/barebox-freescale-imx51-babbage.img > /dev/sdd > # otherwise: > cat barebox-flash-image > /dev/sdd > > The above will overwrite the MBR (and consequently the partition table) > on the destination SD card. To preserve the MBR while writing the rest > -of the image to the card, use:: > +of the image to the card, use: > + > +.. code-block:: sh > > dd if=images/barebox-freescale-imx51-babbage.img of=/dev/sdd bs=1024 skip=1 seek=1 > > -NOTE: MaskROM on i.MX8 expects image to start at +33KiB mark, so the > +Note that MaskROM on i.MX8 expects the image to start at the +33KiB mark, so the > following command has to be used instead: > > +.. code-block:: sh > + > dd if=images/barebox-nxp-imx8mq-evk.img of=/dev/sdd bs=1024 skip=33 seek=33 > > Or, in case of NAND: > > +.. code-block:: sh > + > dd if=images/barebox-nxp-imx8mq-evk.img of=/dev/nand bs=1024 skip=33 seek=1 > > -The images can also always be started second stage:: > +The images can also always be started as second stage on the target: > + > +.. code-block:: console > > - bootm /mnt/tftp/barebox-freescale-imx51-babbage.img > + barebox@Board Name:/ bootm /mnt/tftp/barebox-freescale-imx51-babbage.img > > Using GPT on i.MX > ^^^^^^^^^^^^^^^^^ > > -For i.MX SoCs that place vendor specific header at +1KiB mark of a > -boot medium, special care needs to be taken when parition that medium > -with GPT. In order to make room for i.MX boot header GPT Partition > +For i.MX SoCs that place a vendor specific header at the +1KiB mark of a > +boot medium, special care needs to be taken when partitioning that medium > +with GPT. In order to make room for the i.MX boot header, the GPT Partition > Entry Array needs to be moved from its typical location, LBA 2, to an > offset past vendor specific information. One way to do this would be > -to use ``-j`` or ``--adjust-main-table`` option of ``sgdisk``. For > -example, the following sequence: > +to use the ``-j`` or ``--adjust-main-table`` option of ``sgdisk``. For > +example, the following sequence > + > +.. code-block:: sh > > sgdisk -Z <block device> > sgdisk -o -j 2048 -n 1:8192:+100M <block device> > > will create a single GPT partition starting at LBA 8192 and would > -place Partition Entry Array starting at LBA 2048 which should leave > -enough room for Barebox/i.MX boot header. Once that is done ``dd`` > +place the Partition Entry Array starting at LBA 2048, which should leave > +enough room for the Barebox/i.MX boot header. Once that is done, the ``dd`` > command above can be used to place Barebox on the same medium. > > Information about the ``imx-image`` tool > ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ > > The imx-image tool can be used to generate imximages from raw binaries. > It requires an configuration file describing how to setup the SDRAM on > a particular board. This mainly consists of a poke table. The recognized > options in this file are: > > Header: > > -+----------------+--------------------------------------------------------------+ > -| soc <soctype> |soctype can be one of imx35, imx51, imx53, imx6, imx7, vf610, | > -| | imx8mq | > -+----------------+--------------------------------------------------------------+ > -| loadaddr <adr> | The address the binary is uploaded to | > -+----------------+--------------------------------------------------------------+ > -| dcdofs <ofs> | The offset of the image header in the image. This should be: | > -| | * ``0x400``: MMC/SD, NAND, serial ROM, PATA, SATA | > -| | * ``0x1000``: NOR Flash | > -| | * ``0x100``: OneNAND | > -+----------------+--------------------------------------------------------------+ > ++--------------------+--------------------------------------------------------------+ > +| ``soc <soctype>`` | soctype can be one of imx35, imx51, imx53, imx6, imx7, vf610,| > +| | imx8mq | > ++--------------------+--------------------------------------------------------------+ > +| ``loadaddr <adr>`` | The address the binary is uploaded to | > ++--------------------+--------------------------------------------------------------+ > +| ``dcdofs <ofs>`` | The offset of the image header in the image. This should be: | > +| | | > +| | * ``0x400``: MMC/SD, NAND, serial ROM, PATA, SATA | > +| | * ``0x1000``: NOR Flash | > +| | * ``0x100``: OneNAND | > ++--------------------+--------------------------------------------------------------+ > > Memory manipulation: > > -+------------------------------------+-----------------------------------------+ > -| wm 8 <addr> <value> | write <value> into byte <addr> | > -+------------------------------------+-----------------------------------------+ > -| wm 16 <addr> <value> | write <value> into short <addr> | > -+------------------------------------+-----------------------------------------+ > -| wm 32 <addr> <value> | write <value> into word <addr> | > -+------------------------------------+-----------------------------------------+ > -| set_bits <width> <addr> <value> | set set bits in <value> in <addr> | > -+------------------------------------+-----------------------------------------+ > -| clear_bits <width> <addr> <value> | clear set bits in <value> in <addr> | > -+------------------------------------+-----------------------------------------+ > -| nop | do nothing (just waste time) | > -+------------------------------------+-----------------------------------------+ > - > -<width> can be of 8, 16 or 32. > ++----------------------------------------+-------------------------------------------------+ > +| ``wm 8 <addr> <value>`` | write ``<value>`` into byte ``<addr>`` | > ++----------------------------------------+-------------------------------------------------+ > +| ``wm 16 <addr> <value>`` | write ``<value>`` into short ``<addr>`` | > ++----------------------------------------+-------------------------------------------------+ > +| ``wm 32 <addr> <value>`` | write ``<value>`` into word ``<addr>`` | > ++----------------------------------------+-------------------------------------------------+ > +| ``set_bits <width> <addr> <value>`` | set set bits in ``<value>`` in ``<addr>`` | > ++----------------------------------------+-------------------------------------------------+ > +| ``clear_bits <width> <addr> <value>`` | clear set bits in ``<value>`` in ``<addr>`` | > ++----------------------------------------+-------------------------------------------------+ > +| ``nop`` | do nothing (just waste time) | > ++----------------------------------------+-------------------------------------------------+ > + > +``<width>`` can be one of 8, 16 or 32. > > Checking conditions: > > -+------------------------------------+-----------------------------------------+ > -| check <width> <cond> <addr> <mask> | Poll until condition becomes true. | > -| | with <cond> being one of: | > -| | * ``until_all_bits_clear`` | > -| | * ``until_all_bits_set`` | > -| | * ``until_any_bit_clear`` | > -| | * ``until_any_bit_set`` | > -+------------------------------------+-----------------------------------------+ > ++----------------------------------------+-----------------------------------------+ > +| ``check <width> <cond> <addr> <mask>`` | Poll until condition becomes true. | > +| | with ``<cond>`` being one of: | > +| | | > +| | * ``until_all_bits_clear`` | > +| | * ``until_all_bits_set`` | > +| | * ``until_any_bit_clear`` | > +| | * ``until_any_bit_set`` | > ++----------------------------------------+-----------------------------------------+ > > Some notes about the mentioned *conditions*. > > - ``until_all_bits_clear`` waits until ``(*addr & mask) == 0`` is true > - ``until_all_bits_set`` waits until ``(*addr & mask) == mask`` is true > - ``until_any_bit_clear`` waits until ``(*addr & mask) != mask`` is true > - ``until_any_bit_set`` waits until ``(*addr & mask) != 0`` is true. > > USB Boot > ^^^^^^^^ > > Most boards can be explicitly configured for USB Boot Mode or fall back > to USB Boot when no other medium can be found. The barebox repository > contains a USB upload tool. As it depends on the libusb development headers, > -- > 2.19.1 > > > _______________________________________________ > barebox mailing list > barebox@xxxxxxxxxxxxxxxxxxx > http://lists.infradead.org/mailman/listinfo/barebox > -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox
