Hi!
Thanks, with this patch barebox boots on rk3188.
I've tested with two cards, on one environment can be saved, on other this is not always work.
And newer kernels (above circa 4.10) will not boot with barebox because of clk driver change in Linux kernel.
Looks like It wants DRAM clock change routine that is present in current u-boot, but not in barebox.
mount failure can be fixed by this patch:
diff --git a/arch/arm/boards/radxa-rock/env/boot/mshc1 b/arch/arm/boards/radxa-rock/env/boot/mshc1
index 7393c4e63..df1beb11a 100644
--- a/arch/arm/boards/radxa-rock/env/boot/mshc1
+++ b/arch/arm/boards/radxa-rock/env/boot/mshc1
@@ -1,6 +1,6 @@
#!/bin/sh
-mount /dev/mshc1.0
+mount /dev/mshc1.0 /mnt/mshc1.0
global.bootm.boot_atag=true
oftree -l /mnt/mshc1.0/rk3188-radxarock.dtb
Or just by removal of "mount..." command.
Earlier mount command accepted only device parameter, now it need mountpoint too.
17.09.2018, 18:31, "perachet7@xxxxxxxxx" <perachet7@xxxxxxxxx>:
> Hello Sascha,
>
> Thank you for this patch. Happy to test it here on rk3188 (radxa rock pro).
>
> Using bb v2018.09.0. Applied your patches below. CONFIG_PBL_RELOCATABLE is
> fixed in menuconfig. Common config:
>
> grep RELOCAT .config
> CONFIG_PBL_RELOCATABLE=y
> CONFIG_RELOCATABLE=y
>
> Built using this script:
>
> export ARCH=arm
> #export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
> export CROSS_COMPILE=/opt/OSELAS.Toolchain-2018.02.0/arm-v7m-eabi/gcc-7.3.1-
> newlib-2.5.0-binutils-2.30/bin/arm-v7m-eabi-
>
> rm .config
> make clean
> make ARCH=arm rk3188_defconfig && make -j 10
>
> /rk-makebootable FlashData barebox-flash-image rrboot.bin
> sudo dd if=rrboot.bin of=/dev/sdc bs=$((0x200)) seek=$((0x40))
>
> Using Debian/Ubuntu cross compiler:
> ###########################
>
> CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
>
> DDR Version 1.04 20140217
> In
> DDR3
> 300MHz
> Bus Width=32 Col=10 Bank=8 Row=15 CS=2 Die Bus-Width=16 Size=2048MB
> Memory OK
> OUT
>
> barebox 2018.09.0-dirty #43 Mon Sep 17 15:19:59 CEST 2018
>
> Board: Radxa Rock
> clk_register clk xin24m is already registered, skipping!
> arc-emac 10204000.ethernet: ARC EMAC detected with id: 0x7fd02
> mdio_bus: miibus0: probed
> dw_mmc 10214000.dwmmc: registered as 10214000.dwmmc
> mshc1: detected SD card version 1.0
> mshc1: registered mshc1
> netconsole: registered as netconsole-1
> i2c-gpio i2c-gpio0: using pins 58 (SDA) and 59 (SCL)
> malloc space: 0x9fefd660 -> 0xdfdfacbf (size 1023 MiB)
> gpio-leds.6: probe permanently deferred
> envfs: no envfs (magic mismatch) - envfs never written?
> running /env/bin/init...
>
> Hit any key to stop autoboot: 0
> booting 'mshc1'
> mount: No such file or directory
> ext4 ext40: EXT2 rev 1, inode_size 128, descriptor size 32
> mounted /dev/mshc1.0 on /mnt/mshc1.0
> setting root node failed: Device or resource busy
> oftree: Device or resource busy
>
> Loading ARM Linux zImage '/mnt/mshc1.0/zImage'
> commandline: console=ttyS2,115200 root=/dev/mmcblk0p2 rootwait
> arch_number: 3066
>
> => bb boot success.
> => kernel boot failure.
>
> Using OSELAS:
> ##########
>
> export CROSS_COMPILE=/opt/OSELAS.Toolchain-2018.02.0/arm-v7m-eabi/gcc-7.3.1-
> newlib-2.5.0-binutils-2.30/bin/arm-v7m-eabi-
>
> DDR Version 1.04 20140217
> In
> DDR3
> 300MHz
> Bus Width=32 Col=10 Bank=8 Row=15 CS=2 Die Bus-Width=16 Size=2048MB
> Memory OK
> OUT
>
> barebox 2018.09.0-dirty #44 Mon Sep 17 15:22:34 CEST 2018
>
> Board: Radxa Rock
> clk_register clk xin24m is already registered, skipping!
> arc-emac 10204000.ethernet: ARC EMAC detected with id: 0x7fd02
> mdio_bus: miibus0: probed
> dw_mmc 10214000.dwmmc: registered as 10214000.dwmmc
> mshc1: detected SD card version 1.0
> mshc1: registered mshc1
> netconsole: registered as netconsole-1
> i2c-gpio i2c-gpio0: using pins 58 (SDA) and 59 (SCL)
> malloc space: 0x9fefd660 -> 0xdfdfacbf (size 1023 MiB)
> gpio-leds.6: probe permanently deferred
> envfs: no envfs (magic mismatch) - envfs never written?
> running /env/bin/init...
>
> Hit any key to stop autoboot: 1
> booting 'mshc1'
> mount: No such file or directory
> ext4 ext40: EXT2 rev 1, inode_size 128, descriptor size 32
> mounted /dev/mshc1.0 on /mnt/mshc1.0
> setting root node failed: Device or resource busy
> oftree: Device or resource busy
>
> Loading ARM Linux zImage '/mnt/mshc1.0/zImage'
> commandline: console=ttyS2,115200 root=/dev/mmcblk0p2 rootwait
> arch_number: 3066
>
> => bb boot success.
> => kernel boot failure.
>
> There still are a couple of (possibly unrelated) issues, independent of the
> compiler used:
>
> 1) envfs: no envfs (magic mismatch) - envfs never written?
>
> 2) mount: No such file or directory
>
> 3) setting root node failed: Device or resource busy
>
> 4) oftree: Device or resource busy
>
> 5) arch_number: 3066 [note: boot failure]
>
> cheers
>
> On Montag, 17. September 2018 09:29:42 CEST you wrote:
>> The current way to calculate the compressed image position works
>> with the OSELAS toolchains, but not with the Debian/Ubuntu toolchains.
>> For these toolchains &image_end_marker already returns the correct
>> address, adding global_variable_offset() to it is wrong.
>>
>> The solution seems to be to put the image_end_marker into a different
>> object file so that the compiler cannot play any tricks to resolve
>> the address internally in the object file.
>>
>> Signed-off-by: Sascha Hauer <s.hauer@xxxxxxxxxxxxxx>
>> ---
>> arch/arm/cpu/sections.c | 2 ++
>> arch/arm/cpu/uncompress.c | 5 +----
>> arch/arm/include/asm/sections.h | 2 ++
>> arch/arm/lib/pbl.lds.S | 2 +-
>> 4 files changed, 6 insertions(+), 5 deletions(-)
>>
>> diff --git a/arch/arm/cpu/sections.c b/arch/arm/cpu/sections.c
>> index 5874da2b82..ab08ebf42e 100644
>> --- a/arch/arm/cpu/sections.c
>> +++ b/arch/arm/cpu/sections.c
>> @@ -1,4 +1,5 @@
>> #include <asm/sections.h>
>> +#include <linux/types.h>
>>
>> char __rel_dyn_start[0] __attribute__((section(".__rel_dyn_start")));
>> char __rel_dyn_end[0] __attribute__((section(".__rel_dyn_end")));
>> @@ -9,3 +10,4 @@ char __bss_start[0]
>> __attribute__((section(".__bss_start"))); char __bss_stop[0]
>> __attribute__((section(".__bss_stop")));
>> char __image_start[0] __attribute__((section(".__image_start")));
>> char __image_end[0] __attribute__((section(".__image_end")));
>> +uint32_t __image_end_marker[1]
>> __attribute__((section(".__image_end_marker"))) = { 0xdeadbeef }; diff
>> --git a/arch/arm/cpu/uncompress.c b/arch/arm/cpu/uncompress.c index
>> b07087e4cf..43b49b4212 100644
>> --- a/arch/arm/cpu/uncompress.c
>> +++ b/arch/arm/cpu/uncompress.c
>> @@ -36,9 +36,6 @@
>> unsigned long free_mem_ptr;
>> unsigned long free_mem_end_ptr;
>>
>> -static int __attribute__((__section__(".image_end")))
>> - image_end_marker = 0xdeadbeef;
>> -
>> void __noreturn barebox_multi_pbl_start(unsigned long membase,
>> unsigned long memsize, void *boarddata)
>> {
>> @@ -50,7 +47,7 @@ void __noreturn barebox_multi_pbl_start(unsigned long
>> membase, void *pg_start;
>> unsigned long pc = get_pc();
>>
>> - image_end = (void *)&image_end_marker + global_variable_offset();
>> + image_end = (void *)__image_end_marker + global_variable_offset();
>>
>> if (IS_ENABLED(CONFIG_PBL_RELOCATABLE)) {
>> /*
>
> _______________________________________________
> barebox mailing list
> barebox@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/barebox
--
Андрей
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
