Re: New Board i.MX6 Dual Lite based

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 06/09/2017 08:15 AM, Sascha Hauer wrote:
Hi Gianluca,

On Thu, Jun 08, 2017 at 05:06:46PM +0200, gianluca wrote:
Hello,
I would like to know if somebody has never faced a strange issue using
Barebox (in detail the version I am actually using is 2017.02).

After running the the flash-header for memory using the xlsx file from
FreeScale to setup the memory controller for iMX6 Dual Lite, the boot from
the serial console is saying:


barebox 2017.02.0 #1 Thu Jun 8 15:51:17 CEST 2017


Board: Eurek EK360 i.MX6DL
detected i.MX6 DualLite revision 1.3
mdio_bus: miibus0: probed
imx-usb 2184000.usb: Cannot get phy: Function not implemented
imx-usb 2184000.usb: probe failed: Function not implemented
imx-usb 2184200.usb: Cannot get phy: Function not implemented
imx-usb 2184200.usb: probe failed: Function not implemented

this is pretty strange... Any hint? The device-tree for usb is like that:

You probably have CONFIG_GENERIC_PHY disabled. In this case
of_phy_get_by_phandle() is a static inline returning -ENOSYS.



Yes. It was disabled in the config.

barebox@Eurek EK360 i.MX6DL:/ usb -t
usb: USB: scanning bus for devices...
usb: Bus 001 Device 001: ID 0000:0000 EHCI Host Controller
usb: 1 USB Device(s) found
  1 ID 0000:0000
  |  u-boot EHCI Host Controller
  |
  +-804763968 ID 6c61:3000

Now it works.


		
imx-esdhc 2194000.usdhc: registered as 2194000.usdhc
imx-esdhc 2198000.usdhc: registered as 2198000.usdhc
imx-esdhc 219c000.usdhc: registered as 219c000.usdhc
imx-ipuv3 2400000.ipu: IPUv3H probed
netconsole: registered as netconsole-1
malloc space: 0x2ff7b920 -> 0x4fef723f (size 511.5 MiB)
environment load /dev/env0: No such file or directory
Maybe you have to create the partition.
running /env/bin/init...
Running boot from uSD/MMC or USB...
mmc2: detected SD card version 2.0
mmc2: registered mmc2
ext4 ext40: EXT2 rev 1, inode_size 128

mmc2 is detected and registered because you are booting from it, but
mmc3 is not. Try 'detect mmc3' or 'detect -a' on the command line.


It was missing a mmc3.probe=1 in the init scripts. Now both are recognized correctly.

barebox@Eurek EK360 i.MX6DL:/ detect mmc3
mmc3: detected MMC card version 4.41
mmc3: registered mmc3.boot0
mmc3: registered mmc3.boot1
mmc3: registered mmc3

     `-- eth0
         `-- 2194000.usdhc
            `-- mmc1
         `-- 2198000.usdhc
            `-- mmc2
               `-- 0x00000000-0xefffffff (   3.8 GiB): /dev/mmc2
               `-- 0x00400000-0x00bfffff (     8 MiB): /dev/mmc2.0
               `-- 0x00c00000-0x02bfffff (    32 MiB): /dev/mmc2.1
               `-- 0x02c00000-0xefffffff (   3.7 GiB): /dev/mmc2.2
               `-- ext40
         `-- 219c000.usdhc
            `-- mmc3
               `-- 0x00000000-0x001fffff (     2 MiB): /dev/mmc3.boot0
               `-- 0x00000000-0x001fffff (     2 MiB): /dev/mmc3.boot1
               `-- 0x00000000-0xe4ffffff (   3.6 GiB): /dev/mmc3



i2c0: <i2c_fsl_bus_busy> timeout waiting for I2C bus busy
ek360_read_eeprom :Error on reading eeprom @ 0
ek360_read_eeprom :Error on reading bytes.
ek360_detect_hw :** ERROR on READ EEPROM BOARD ret: -1
Hit CTRL-C key to stop autoboot:  1

Another issue is the i2c bus.

You should measure the I2C data line with an oscilloscope. It could be
that the line is constantly low. This can happen if the pullup resistor
is missing (Pinmux?). Also in rare cases this can happen when a board is
resetted in the middle of a I2C transfer.


Now I am trying to extend the I2C Lines outside the board for a oscilloscope and/or a Saleae Logic Bus Analyzer. As soon as I find the solution or not I will keep you informed.

Anyway in the config there is both GPIO BASED I2C DRIVER and Platform iMX Driver. I tried to disable the GPIO Based but it does not work.

Now I am thinking about some pulled-low/high line by some chips in the board. I will see.

Thanks!
--
Eurek s.r.l.                          |
Electronic Engineering                | http://www.eurek.it
via Celletta 8/B, 40026 Imola, Italy  | Phone: +39-(0)542-609120
p.iva 00690621206 - c.f. 04020030377  | Fax:   +39-(0)542-609212

_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox



[Index of Archives]     [Linux Embedded]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux