Re: [PATCH 6/8] ARM: Add phyCORE-RK3288 SOM support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jul 20, 2016 at 7:17 AM, Wadim Egorov <w.egorov@xxxxxxxxx> wrote:
> The phyCORE-RK3288 aka PCM-059 is a SoM (System on Module)
> containing a RK3288 SoC. The module can be connected to different
> carrier boards.
>
> Signed-off-by: Wadim Egorov <w.egorov@xxxxxxxxx>
> ---
>  arch/arm/boards/Makefile                           |   1 +
>  arch/arm/boards/phytec-som-rk3288/Makefile         |   3 +
>  arch/arm/boards/phytec-som-rk3288/board.c          |  31 +++++
>  .../defaultenv-physom-rk3288/boot/emmc             |   6 +
>  .../defaultenv-physom-rk3288/boot/mmc              |   6 +
>  .../defaultenv-physom-rk3288/init/automount        |  12 ++
>  .../defaultenv-physom-rk3288/init/bootsource       |   3 +
>  arch/arm/boards/phytec-som-rk3288/lowlevel.c       |  44 ++++++
>  arch/arm/dts/Makefile                              |   1 +
>  arch/arm/dts/rk3288-phycore-som.dts                | 148 +++++++++++++++++++++
>  arch/arm/mach-rockchip/Kconfig                     |   7 +
>  images/Makefile.rockchip                           |   4 +
>  12 files changed, 266 insertions(+)
>  create mode 100644 arch/arm/boards/phytec-som-rk3288/Makefile
>  create mode 100644 arch/arm/boards/phytec-som-rk3288/board.c
>  create mode 100644 arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/boot/emmc
>  create mode 100644 arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/boot/mmc
>  create mode 100644 arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/init/automount
>  create mode 100644 arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/init/bootsource
>  create mode 100644 arch/arm/boards/phytec-som-rk3288/lowlevel.c
>  create mode 100644 arch/arm/dts/rk3288-phycore-som.dts
>
> diff --git a/arch/arm/boards/Makefile b/arch/arm/boards/Makefile
> index 9241b66..24ce130 100644
> --- a/arch/arm/boards/Makefile
> +++ b/arch/arm/boards/Makefile
> @@ -95,6 +95,7 @@ obj-$(CONFIG_MACH_PM9G45)                     += pm9g45/
>  obj-$(CONFIG_MACH_QIL_A9260)                   += qil-a926x/
>  obj-$(CONFIG_MACH_QIL_A9G20)                   += qil-a926x/
>  obj-$(CONFIG_MACH_RADXA_ROCK)                  += radxa-rock/
> +obj-$(CONFIG_MACH_PHYTEC_SOM_RK3288)           += phytec-som-rk3288/
>  obj-$(CONFIG_MACH_REALQ7)                      += datamodul-edm-qmx6/
>  obj-$(CONFIG_MACH_RPI_COMMON)                  += raspberry-pi/
>  obj-$(CONFIG_MACH_SABRELITE)                   += freescale-mx6-sabrelite/
> diff --git a/arch/arm/boards/phytec-som-rk3288/Makefile b/arch/arm/boards/phytec-som-rk3288/Makefile
> new file mode 100644
> index 0000000..6f34c9a
> --- /dev/null
> +++ b/arch/arm/boards/phytec-som-rk3288/Makefile
> @@ -0,0 +1,3 @@
> +obj-y += board.o
> +lwl-y += lowlevel.o
> +bbenv-y += defaultenv-physom-rk3288
> diff --git a/arch/arm/boards/phytec-som-rk3288/board.c b/arch/arm/boards/phytec-som-rk3288/board.c
> new file mode 100644
> index 0000000..8ea6c6c
> --- /dev/null
> +++ b/arch/arm/boards/phytec-som-rk3288/board.c
> @@ -0,0 +1,31 @@
> +/*
> + * Copyright (C) 2016 PHYTEC Messtechnik GmbH,
> + * Author: Wadim Egorov <w.egorov@xxxxxxxxx>
> + *
> + * Device initialization for the phyCORE-RK3288 SoM
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <common.h>
> +#include <init.h>
> +#include <envfs.h>
> +
> +static int physom_devices_init(void)
> +{
> +       if (!of_machine_is_compatible("phytec,rk3288-phycore-som"))
> +               return 0;
> +
> +       barebox_set_hostname("pcm059");
> +       defaultenv_append_directory(defaultenv_physom_rk3288);
> +
> +       return 0;
> +}
> +device_initcall(physom_devices_init);
> diff --git a/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/boot/emmc b/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/boot/emmc
> new file mode 100644
> index 0000000..731b07f
> --- /dev/null
> +++ b/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/boot/emmc
> @@ -0,0 +1,6 @@
> +#!/bin/sh
> +
> +global.bootm.image=/mnt/emmc/linuximage
> +global.bootm.oftree=/mnt/emmc/oftree
> +
> +global.linux.bootargs.dyn.root="root=/dev/mmcblk0p2 rw rootwait"
> diff --git a/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/boot/mmc b/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/boot/mmc
> new file mode 100644
> index 0000000..1b743c5
> --- /dev/null
> +++ b/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/boot/mmc
> @@ -0,0 +1,6 @@
> +#!/bin/sh
> +
> +global.bootm.image=/mnt/sdmmc/linuximage
> +global.bootm.oftree=/mnt/sdmmc/oftree
> +
> +global.linux.bootargs.dyn.root="root=/dev/mmcblk0p2 rw rootwait"
> diff --git a/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/init/automount b/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/init/automount
> new file mode 100644
> index 0000000..2f9d78a
> --- /dev/null
> +++ b/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/init/automount
> @@ -0,0 +1,12 @@
> +#!/bin/sh
> +
> +if [ "$1" = menu ]; then
> +       init-menu-add-entry "$0" "Automountpoints"
> +       exit
> +fi
> +
> +mkdir -p /mnt/emmc
> +automount -d /mnt/emmc 'mshc0.probe=1 && [ -e /dev/mshc0.0 ] && mount /dev/mshc0.0 /mnt/emmc'
> +
> +mkdir -p /mnt/sdmmc
> +automount -d /mnt/sdmmc 'mshc1.probe=1 && [ -e /dev/mshc1.0 ] && mount /dev/mshc1.0 /mnt/sdmmc'
> diff --git a/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/init/bootsource b/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/init/bootsource
> new file mode 100644
> index 0000000..36d34e3
> --- /dev/null
> +++ b/arch/arm/boards/phytec-som-rk3288/defaultenv-physom-rk3288/init/bootsource
> @@ -0,0 +1,3 @@
> +#!/bin/sh
> +
> +global.boot.default="emmc mmc"
> diff --git a/arch/arm/boards/phytec-som-rk3288/lowlevel.c b/arch/arm/boards/phytec-som-rk3288/lowlevel.c
> new file mode 100644
> index 0000000..7804a55
> --- /dev/null
> +++ b/arch/arm/boards/phytec-som-rk3288/lowlevel.c
> @@ -0,0 +1,44 @@
> +/*
> + * Copyright (C) 2016 PHYTEC Messtechnik GmbH,
> + * Author: Wadim Egorov <w.egorov@xxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <common.h>
> +#include <linux/sizes.h>
> +#include <asm/barebox-arm-head.h>
> +#include <asm/barebox-arm.h>
> +#include <mach/rk3288-regs.h>
> +#include <mach/grf_rk3288.h>
> +#include <mach/hardware.h>
> +#include <debug_ll.h>
> +
> +extern char __dtb_rk3288_phycore_som_start[];
> +
> +ENTRY_FUNCTION(start_rk3288_phycore_som, r0, r1, r2)
> +{
> +       void *fdt;
> +       arm_cpu_lowlevel_init();
> +
> +       if (IS_ENABLED(CONFIG_DEBUG_LL)) {
> +               struct rk3288_grf * const grf = (void *)RK3288_GRF_BASE;
> +               rk_clrsetreg(&grf->gpio4c_iomux,
> +                       GPIO4C1_MASK << GPIO4C1_SHIFT |
> +                       GPIO4C0_MASK << GPIO4C0_SHIFT,
> +                       GPIO4C1_UART0BT_SOUT << GPIO4C1_SHIFT |
> +                       GPIO4C0_UART0BT_SIN << GPIO4C0_SHIFT);

Would it be possible to replace rk_clrsetreg() with clrsetbits() ?

> +               INIT_LL();
> +       }
> +
> +       fdt = __dtb_rk3288_phycore_som_start - get_runtime_offset();
> +
> +       barebox_arm_entry(0x0, SZ_1G, fdt);
> +}
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 813e098..77c9ff3 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -54,6 +54,7 @@ pbl-dtb-$(CONFIG_MACH_PHYTEC_SOM_IMX6) += imx6q-phytec-pbaa03.dtb.o \
>  pbl-dtb-$(CONFIG_MACH_PLATHOME_OPENBLOCKS_AX3) += armada-xp-openblocks-ax3-4-bb.dtb.o
>  pbl-dtb-$(CONFIG_MACH_PLATHOME_OPENBLOCKS_A6) += kirkwood-openblocks_a6-bb.dtb.o
>  pbl-dtb-$(CONFIG_MACH_RADXA_ROCK) += rk3188-radxarock.dtb.o
> +pbl-dtb-$(CONFIG_MACH_PHYTEC_SOM_RK3288) += rk3288-phycore-som.dtb.o
>  pbl-dtb-$(CONFIG_MACH_REALQ7) += imx6q-dmo-edmqmx6.dtb.o
>  pbl-dtb-$(CONFIG_MACH_SABRELITE) += imx6q-sabrelite.dtb.o imx6dl-sabrelite.dtb.o
>  pbl-dtb-$(CONFIG_MACH_SABRESD) += imx6q-sabresd.dtb.o
> diff --git a/arch/arm/dts/rk3288-phycore-som.dts b/arch/arm/dts/rk3288-phycore-som.dts
> new file mode 100644
> index 0000000..05ddd9c
> --- /dev/null
> +++ b/arch/arm/dts/rk3288-phycore-som.dts
> @@ -0,0 +1,148 @@
> +/*
> + * Copyright (C) 2016 PHYTEC Messtechnik GmbH,
> + * Author: Wadim Egorov <w.egorov@xxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +/dts-v1/;
> +
> +#include <arm/rk3288.dtsi>
> +
> +/ {
> +       model = "phycore-rk3288";
> +       compatible = "phytec,rk3288-phycore-som", "rockchip,rk3288";
> +
> +       memory {
> +               reg = <0 0x40000000>;
> +       };
> +
> +       vcc33: fixedregulator@0 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "vcc33";
> +               regulator-min-microvolt = <3300000>;
> +               regulator-max-microvolt = <3300000>;
> +               startup-delay-us = <100000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +
> +       vcc18: fixedregulator@1 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "vcc18";
> +               regulator-min-microvolt = <1800000>;
> +               regulator-max-microvolt = <1800000>;
> +               regulator-boot-on;
> +               regulator-always-on;
> +       };
> +
> +       chosen {
> +               stdout-path = &uart0;
> +
> +               environment-emmc {
> +                       compatible = "barebox,environment";
> +                       device-path = &emmc, "partname:barebox-environment";
> +                       status = "disabled";
> +               };
> +
> +               environment-sdmmc {
> +                       compatible = "barebox,environment";
> +                       device-path = &sdmmc, "partname:barebox-environment";
> +                       status = "disabled";
> +               };
> +       };
> +};
> +
> +&pinctrl {
> +       sdmmc {
> +               sdmmc_pwr: sdmmc-pwr {
> +                       rockchip,pins = <7 11 RK_FUNC_GPIO &pcfg_pull_none>;
> +               };
> +       };
> +};
> +
> +&i2c0 {
> +       clock-frequency = <400000>;
> +       status = "okay";
> +};
> +
> +&emmc {
> +       broken-cd;
> +       bus-width = <8>;
> +       cap-mmc-highspeed;
> +       disable-wp;
> +       non-removable;
> +       num-slots = <1>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_pwr>, <&emmc_bus8>;
> +       vmmc-supply = <&vcc33>;
> +       vqmmc-supply = <&vcc18>;
> +       status = "okay";
> +
> +       #size-cells = <1>;
> +       #address-cells = <1>;
> +
> +       partition@8000 {
> +               label = "spl";
> +               reg = <0x8000 0x8000>;
> +       };
> +
> +       partition@20000 {
> +               label = "barebox";
> +               reg = <0x20000 0xe0000>;
> +       };
> +
> +       partition@e0000 {
> +               label = "barebox-environment";
> +               reg = <0xe0000 0x20000>;
> +       };
> +};
> +
> +&sdmmc {
> +       bus-width = <4>;
> +       cap-mmc-highspeed;
> +       cap-sd-highspeed;
> +       card-detect-delay = <200>;
> +       disable-wp;
> +       num-slots = <1>;
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&sdmmc_clk>, <&sdmmc_cmd>, <&sdmmc_cd>, <&sdmmc_bus4>;
> +       vmmc-supply = <&vcc33>;
> +       status = "okay";
> +
> +       #address-cells = <1>;
> +       #size-cells = <1>;
> +
> +       partition@8000 {
> +               label = "spl";
> +               reg = <0x8000 0x8000>;
> +       };
> +
> +       partition@20000 {
> +               label = "barebox";
> +               reg = <0x20000 0xe0000>;
> +       };
> +
> +       partition@e0000 {
> +               label = "barebox-environment";
> +               reg = <0xe0000 0x20000>;
> +       };
> +};
> +
> +&uart0 {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&uart0_xfer>, <&uart0_cts>, <&uart0_rts>;
> +       reg-shift = <2>;
> +       status = "okay";
> +};
> +
> +&uart2 {
> +       status = "okay";
> +};
> diff --git a/arch/arm/mach-rockchip/Kconfig b/arch/arm/mach-rockchip/Kconfig
> index fa0e8fc..6f02643 100644
> --- a/arch/arm/mach-rockchip/Kconfig
> +++ b/arch/arm/mach-rockchip/Kconfig
> @@ -30,4 +30,11 @@ config MACH_RADXA_ROCK
>         select MFD_ACT8846
>         bool "Radxa rock board"
>
> +config MACH_PHYTEC_SOM_RK3288
> +       depends on ARCH_RK3288
> +       select I2C
> +       bool "RK3288 phyCORE SOM"
> +       help
> +         Say Y here if you are using a RK3288 based Phytecs SOM
> +
>  endmenu
> diff --git a/images/Makefile.rockchip b/images/Makefile.rockchip
> index 9715b92..3f1ee57 100644
> --- a/images/Makefile.rockchip
> +++ b/images/Makefile.rockchip
> @@ -5,3 +5,7 @@
>  pblx-$(CONFIG_MACH_RADXA_ROCK) += start_radxa_rock
>  FILE_barebox-radxa-rock.img = start_radxa_rock.pblx
>  image-$(CONFIG_MACH_RADXA_ROCK) += barebox-radxa-rock.img
> +
> +pblx-$(CONFIG_MACH_PHYTEC_SOM_RK3288) += start_rk3288_phycore_som
> +FILE_barebox-rk3288-phycore-som.img = start_rk3288_phycore_som.pblx
> +image-$(CONFIG_MACH_PHYTEC_SOM_RK3288) += barebox-rk3288-phycore-som.img
> --
> 1.9.1
>
>
> _______________________________________________
> barebox mailing list
> barebox@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/barebox

_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox



[Index of Archives]     [Linux Embedded]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux