Port DS1337 specific bits from corresponding Linux driver and add
small changes needed for DS1341.
Signed-off-by: Andrey Smirnov <andrew.smirnov@xxxxxxxxx>
---
drivers/rtc/rtc-ds1307.c | 91 ++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 91 insertions(+)
diff --git a/drivers/rtc/rtc-ds1307.c b/drivers/rtc/rtc-ds1307.c
index d78faa8..2b46ae5 100644
--- a/drivers/rtc/rtc-ds1307.c
+++ b/drivers/rtc/rtc-ds1307.c
@@ -31,7 +31,9 @@
*/
enum ds_type {
ds_1307,
+ ds_1337,
ds_1338,
+ ds_1341,
last_ds_type /* always last */
};
@@ -62,6 +64,28 @@ enum ds_type {
# define DS1307_BIT_SQWE 0x10
# define DS1307_BIT_RS1 0x02
# define DS1307_BIT_RS0 0x01
+#define DS1337_REG_CONTROL 0x0e
+# define DS1337_BIT_nEOSC 0x80
+# define DS1339_BIT_BBSQI 0x20
+# define DS3231_BIT_BBSQW 0x40 /* same as BBSQI */
+# define DS1337_BIT_RS2 0x10
+# define DS1337_BIT_RS1 0x08
+# define DS1337_BIT_INTCN 0x04
+# define DS1337_BIT_A2IE 0x02
+# define DS1337_BIT_A1IE 0x01
+#define DS1340_REG_CONTROL 0x07
+# define DS1340_BIT_OUT 0x80
+# define DS1340_BIT_FT 0x40
+# define DS1340_BIT_CALIB_SIGN 0x20
+# define DS1340_M_CALIBRATION 0x1f
+#define DS1340_REG_FLAG 0x09
+# define DS1340_BIT_OSF 0x80
+#define DS1337_REG_STATUS 0x0f
+# define DS1337_BIT_OSF 0x80
+# define DS1341_BIT_ECLK 0x04
+# define DS1337_BIT_A2I 0x02
+# define DS1337_BIT_A1I 0x01
+
struct ds1307 {
struct rtc_device rtc;
@@ -78,7 +102,9 @@ struct ds1307 {
static struct platform_device_id ds1307_id[] = {
{ "ds1307", ds_1307 },
+ { "ds1337", ds_1337 },
{ "ds1338", ds_1338 },
+ { "ds1341", ds_1341 },
{ "pt7c4338", ds_1307 },
{ }
};
@@ -224,6 +250,16 @@ static int ds1307_set_time(struct rtc_device *rtcdev, struct rtc_time *t)
tmp = t->tm_year - 100;
buf[DS1307_REG_YEAR] = bin2bcd(tmp);
+ switch (ds1307->type) {
+ case ds_1337:
+ case ds_1341:
+ buf[DS1307_REG_MONTH] |= DS1337_BIT_CENTURY;
+ break;
+ default:
+ break;
+ }
+
+
dev_dbg(dev, "%s: %7ph\n", "write", buf);
result = ds1307->write_block_data(ds1307->client,
@@ -263,6 +299,61 @@ static int ds1307_probe(struct device_d *dev)
ds1307->read_block_data = ds1307_read_block_data;
ds1307->write_block_data = ds1307_write_block_data;
+
+ switch (ds1307->type) {
+ case ds_1337:
+ case ds_1341:
+ /* get registers that the "rtc" read below won't read... */
+ tmp = ds1307->read_block_data(ds1307->client,
+ DS1337_REG_CONTROL, 2, buf);
+
+ if (tmp != 2) {
+ dev_dbg(&client->dev, "read error %d\n", tmp);
+ err = -EIO;
+ goto exit;
+ }
+
+ /* oscillator off? turn it on, so clock can tick. */
+ if (ds1307->regs[0] & DS1337_BIT_nEOSC)
+ ds1307->regs[0] &= ~DS1337_BIT_nEOSC;
+
+
+ /*
+ Make sure no alarm interrupts or square wave signals
+ are produced by the chip while we are in
+ bootloader. We do this by configuring the RTC to
+ generate alarm interrupts (thus disabling square
+ wave generation), but disabling each individual
+ alarm interrupt source
+ */
+ ds1307->regs[0] |= DS1337_BIT_INTCN;
+ ds1307->regs[0] &= ~(DS1337_BIT_A2IE | DS1337_BIT_A1IE);
+
+ i2c_smbus_write_byte_data(client, DS1337_REG_CONTROL,
+ ds1307->regs[0]);
+
+ /*
+ For the above to be true, DS1341 also has to have
+ ECLK bit set to 0
+ */
+ if (ds1307->type == ds_1341) {
+ ds1307->regs[1] &= DS1341_BIT_ECLK;
+ i2c_smbus_write_byte_data(client, DS1337_REG_STATUS,
+ ds1307->regs[1]);
+ }
+
+
+ /* oscillator fault? clear flag, and warn */
+ if (ds1307->regs[1] & DS1337_BIT_OSF) {
+ i2c_smbus_write_byte_data(client, DS1337_REG_STATUS,
+ ds1307->regs[1] & ~DS1337_BIT_OSF);
+ dev_warn(&client->dev, "SET TIME!\n");
+ }
+
+ default:
+ break;
+ }
+
read_rtc:
/* read RTC registers */
tmp = ds1307->read_block_data(client, ds1307->offset, 8, buf);
--
2.5.0
_______________________________________________
barebox mailing list
barebox@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/barebox
