On 04/09/2011 03:23 PM, Sascha Hauer wrote: > On Fri, Apr 08, 2011 at 12:24:00PM +0200, Marc Kleine-Budde wrote: >> This patch adds support for tje mx28-evk board. NAND support is still lacking, >> so we use still the bootlets as the first stage boot loader. >> >> Signed-off-by: Marc Kleine-Budde <mkl@xxxxxxxxxxxxxx> >> --- >> arch/arm/Makefile | 1 + >> arch/arm/boards/freescale-mx28-evk/Makefile | 1 + >> arch/arm/boards/freescale-mx28-evk/config.h | 16 + >> arch/arm/boards/freescale-mx28-evk/env/config | 67 ++++ >> arch/arm/boards/freescale-mx28-evk/mx28-evk.c | 378 ++++++++++++++++++++++ >> arch/arm/boards/freescale-mx28-evk/tx28-stk5.c | 410 ++++++++++++++++++++++++ > > Looks like you copied a bit too much from the karo board. doh! > >> + >> +console_initcall(mx28_evk_console_init); >> + >> +/** >> +@page mx28_evk KARO's MX28_EVK CPU module >> + >> +@section mx28_evk_cpu_card The CPU module >> + >> +http://www.karo-electronics.de/ >> + >> +This CPU card is based on a Freescale i.MX28 CPU. The card is shipped with: >> + >> +- 128 MiB synchronous dynamic RAM (DDR2 type), 200 MHz support >> +- 128 MiB NAND K9F1G08U0A (3.3V type) >> +- PCA9554 GPIO expander >> +- DS1339 RTC >> +- LAN8710 Phy >> + >> +@section mx28_evk_basboards Supported baseboards >> + >> +Supported baseboards are: >> +- KARO's Starterkit 5 >> + >> +@section mx28_evk_stk5_howto How to get barebox for 'KARO's Starterkit 5' >> + >> +Using the default configuration: >> + >> +@verbatim >> +make ARCH=arm mx28_evkstk5_defconfig >> +@endverbatim >> + >> +Build the binary image: >> + >> +@verbatim >> +make ARCH=arm CROSS_COMPILE=armv5compiler >> +@endverbatim >> + >> +@note replace the armv5compiler with your ARM v5 cross compiler. >> + >> +@note To use the result, you also need the following resources from Freescale: >> +- the 'bootlets' archive >> +- the 'elftosb2' encryption tool >> +- in the case you want to start @b barebox from an attached SD card the >> + 'sdimage' tool from Freescale's 'uuc' archive. >> + >> +@section mx28_evk_mlayout Memory layout when barebox is running: >> + >> +- 0x40000000 start of SDRAM >> +- 0x40000100 start of kernel's boot parameters >> + - below malloc area: stack area >> + - below barebox: malloc area >> +- 0x47000000 start of @b barebox > > Please either correct this or remove it. I'll remove it Marc -- Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
Attachment:
signature.asc
Description: OpenPGP digital signature
_______________________________________________ barebox mailing list barebox@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/barebox
