Hi Guys,
A quick run of "smartctl /dev/sda -a" gives me no errors.
Log follows:-
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax 10 (SATA/300)
Device Model: Maxtor 6V200E0
Serial Number: V40KPSSG
LU WWN Device Id: 0 150500 7da7feb4f
Firmware Version: VA111630
User Capacity: 203,928,109,056 bytes [203 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 T13/1532D revision 0
Local Time is: Fri Mar 16 20:22:57 2018 GMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
I thought that this disk was 500Gb, it says above 203Gb, or is that
value the used space. It shows 458Gb + 25Gb in "My Computer"
It also shows the 458Gb partition as sdf1.
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection
activity
was never started.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 4622) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline
immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection
upon new
command.
Offline surface scan
supported.
Self-test supported.
No Conveyance Self-test
supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before
entering
power-saving mode.
Supports SMART auto save
timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging
supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 90) minutes.
SCT capabilities: (0x0021) SCT Status supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 32
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 208 208 063 Pre-fail
Always - 13404
4 Start_Stop_Count 0x0032 253 253 000 Old_age
Always - 75
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000a 253 211 000 Old_age
Always - 0
8 Seek_Time_Performance 0x0027 251 240 187 Pre-fail
Always - 54359
9 Power_On_Hours 0x0032 251 251 000 Old_age
Always - 718
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 252 252 000 Old_age
Always - 648
189 High_Fly_Writes 0x003a 100 100 000 Old_age
Always - 0
190 Airflow_Temperature_Cel 0x0022 060 060 000 Old_age
Always - 40 (Min/Max 13/40)
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age
Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age
Always - 0
194 Temperature_Celsius 0x0032 034 253 000 Old_age
Always - 40
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age
Always - 1132
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age
Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age
Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age
Offline - 0
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age
Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age
Always - 0
202 Data_Address_Mark_Errs 0x000a 253 252 000 Old_age
Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail
Always - 0
204 Soft_ECC_Correction 0x000a 253 252 000 Old_age
Always - 0
205 Thermal_Asperity_Rate 0x000a 253 252 000 Old_age
Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age
Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age
Always - 0
210 Unknown_Attribute 0x0032 253 252 000 Old_age
Always - 0
211 Unknown_Attribute 0x0032 253 252 000 Old_age
Always - 0
212 Unknown_Attribute 0x0032 253 252 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.
--
Best Regards:
Baron
---------------------------------------------------------------------
To unsubscribe, e-mail: trinity-users-unsubscribe@xxxxxxxxxxxxxxxxxxxxxxxxxx
For additional commands, e-mail: trinity-users-help@xxxxxxxxxxxxxxxxxxxxxxxxxx
Read list messages on the web archive: http://trinity-users.pearsoncomputing.net/
Please remember not to top-post: http://trinity.pearsoncomputing.net/mailing_lists/#top-posting
