Re: [PATCH 2/2] usb: typec: tcpm: fix the sender response time issue

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Dec 20, 2024 at 5:39 AM Jos Wang <joswang1221@xxxxxxxxx> wrote:
>
> Thank you for your help in reviewing the code.
>
> USB PD3 CTS specification:
> https://usb.org/document-library/usb-power-delivery-compliance-test-specification-0
> Should this link be added to the commit message?
>
> I will resubmit the code as soon as possible and put patch 1/2 and 2/2
> in the same thread.
>
> On Wed, Dec 18, 2024 at 6:03 PM Heikki Krogerus
> <heikki.krogerus@xxxxxxxxxxxxxxx> wrote:
> >
> > Hi,
> >
> > On Sun, Dec 15, 2024 at 08:50:13PM +0800, joswang wrote:
> > > From: Jos Wang <joswang@xxxxxxxxxx>
> > >
> > > According to the USB PD3 CTS specification, the requirements
> >
> > What is "USB PD3 CTS specification"? Please open it here.
> >
> > > for tSenderResponse are different in PD2 and PD3 modes, see
> > > Table 19 Timing Table & Calculations. For PD2 mode, the
> > > tSenderResponse min 24ms and max 30ms; for PD3 mode, the
> > > tSenderResponse min 27ms and max 33ms.
> > >
> > > For the "TEST.PD.PROT.SRC.2 Get_Source_Cap No Request" test
> > > item, after receiving the Source_Capabilities Message sent by
> > > the UUT, the tester deliberately does not send a Request Message
> > > in order to force the SenderResponse timer on the Source UUT to
> > > timeout. The Tester checks that a Hard Reset is detected between
> > > tSenderResponse min and max,the delay is between the last bit of
> > > the GoodCRC Message EOP has been sent and the first bit of Hard
> > > Reset SOP has been received. The current code does not distinguish
> > > between PD2 and PD3 modes, and tSenderResponse defaults to 60ms.
> > > This will cause this test item and the following tests to fail:
> > > TEST.PD.PROT.SRC3.2 SenderResponseTimer Timeout
> > > TEST.PD.PROT.SNK.6 SenderResponseTimer Timeout
> > >
> > > Considering factors such as SOC performance, i2c rate, and the speed
> > > of PD chip sending data, "pd2-sender-response-time-ms" and
> > > "pd3-sender-response-time-ms" DT time properties are added to allow
> > > users to define platform timing. For values that have not been
> > > explicitly defined in DT using this property, a default value of 27ms
> > > for PD2 tSenderResponse and 30ms for PD3 tSenderResponse is set.
> > >
> > > Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)")
> > > Cc: stable@xxxxxxxxxxxxxxx
> > > Signed-off-by: Jos Wang <joswang@xxxxxxxxxx>
> >
> > If this is a fix, then I think it's fixing commit 2eadc33f40d4
> > ("typec: tcpm: Add core support for sink side PPS"). That's where the
> > pd_revision was changed to 3.0.

Hmm, this patch also relies upon
https://lore.kernel.org/all/20241022-pd-dt-time-props-v1-2-fea96f51b302@xxxxxxxxxx/
so not sure whether it could be Fixes: 2eadc33f40d4 ("typec: tcpm: Add
core support for sink side PPS")

The patch looks good otherwise. Will wait for Jos's resubmission based
on his previous response.

> >
> > Badhri, could you take a look at this (and how about that
> > maintainer role? :-) ).

This took time was lining up the logistics.
Will send out a patch proposing me and a few others right after the
new year break.

Regards,
Badhri

> >
> > > ---
> > >  drivers/usb/typec/tcpm/tcpm.c | 50 +++++++++++++++++++++++------------
> > >  include/linux/usb/pd.h        |  3 ++-
> > >  2 files changed, 35 insertions(+), 18 deletions(-)
> > >
> > > diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
> > > index 6021eeb903fe..3a159bfcf382 100644
> > > --- a/drivers/usb/typec/tcpm/tcpm.c
> > > +++ b/drivers/usb/typec/tcpm/tcpm.c
> > > @@ -314,12 +314,16 @@ struct pd_data {
> > >   * @sink_wait_cap_time: Deadline (in ms) for tTypeCSinkWaitCap timer
> > >   * @ps_src_wait_off_time: Deadline (in ms) for tPSSourceOff timer
> > >   * @cc_debounce_time: Deadline (in ms) for tCCDebounce timer
> > > + * @pd2_sender_response_time: Deadline (in ms) for pd20 tSenderResponse timer
> > > + * @pd3_sender_response_time: Deadline (in ms) for pd30 tSenderResponse timer
> > >   */
> > >  struct pd_timings {
> > >       u32 sink_wait_cap_time;
> > >       u32 ps_src_off_time;
> > >       u32 cc_debounce_time;
> > >       u32 snk_bc12_cmpletion_time;
> > > +     u32 pd2_sender_response_time;
> > > +     u32 pd3_sender_response_time;
> > >  };
> > >
> > >  struct tcpm_port {
> > > @@ -3776,7 +3780,9 @@ static bool tcpm_send_queued_message(struct tcpm_port *port)
> > >                       } else if (port->pwr_role == TYPEC_SOURCE) {
> > >                               tcpm_ams_finish(port);
> > >                               tcpm_set_state(port, HARD_RESET_SEND,
> > > -                                            PD_T_SENDER_RESPONSE);
> > > +                                            port->negotiated_rev >= PD_REV30 ?
> > > +                                            port->timings.pd3_sender_response_time :
> > > +                                            port->timings.pd2_sender_response_time);
> > >                       } else {
> > >                               tcpm_ams_finish(port);
> > >                       }
> > > @@ -4619,6 +4625,9 @@ static void run_state_machine(struct tcpm_port *port)
> > >       enum typec_pwr_opmode opmode;
> > >       unsigned int msecs;
> > >       enum tcpm_state upcoming_state;
> > > +     u32 sender_response_time = port->negotiated_rev >= PD_REV30 ?
> > > +                                port->timings.pd3_sender_response_time :
> > > +                                port->timings.pd2_sender_response_time;
> > >
> > >       if (port->tcpc->check_contaminant && port->state != CHECK_CONTAMINANT)
> > >               port->potential_contaminant = ((port->enter_state == SRC_ATTACH_WAIT &&
> > > @@ -5113,7 +5122,7 @@ static void run_state_machine(struct tcpm_port *port)
> > >                       tcpm_set_state(port, SNK_WAIT_CAPABILITIES, 0);
> > >               } else {
> > >                       tcpm_set_state_cond(port, hard_reset_state(port),
> > > -                                         PD_T_SENDER_RESPONSE);
> > > +                                         sender_response_time);
> > >               }
> > >               break;
> > >       case SNK_NEGOTIATE_PPS_CAPABILITIES:
> > > @@ -5135,7 +5144,7 @@ static void run_state_machine(struct tcpm_port *port)
> > >                               tcpm_set_state(port, SNK_READY, 0);
> > >               } else {
> > >                       tcpm_set_state_cond(port, hard_reset_state(port),
> > > -                                         PD_T_SENDER_RESPONSE);
> > > +                                         sender_response_time);
> > >               }
> > >               break;
> > >       case SNK_TRANSITION_SINK:
> > > @@ -5387,7 +5396,7 @@ static void run_state_machine(struct tcpm_port *port)
> > >                       port->message_id_prime = 0;
> > >                       port->rx_msgid_prime = -1;
> > >                       tcpm_pd_send_control(port, PD_CTRL_SOFT_RESET, TCPC_TX_SOP_PRIME);
> > > -                     tcpm_set_state_cond(port, ready_state(port), PD_T_SENDER_RESPONSE);
> > > +                     tcpm_set_state_cond(port, ready_state(port), sender_response_time);
> > >               } else {
> > >                       port->message_id = 0;
> > >                       port->rx_msgid = -1;
> > > @@ -5398,7 +5407,7 @@ static void run_state_machine(struct tcpm_port *port)
> > >                               tcpm_set_state_cond(port, hard_reset_state(port), 0);
> > >                       else
> > >                               tcpm_set_state_cond(port, hard_reset_state(port),
> > > -                                                 PD_T_SENDER_RESPONSE);
> > > +                                                 sender_response_time);
> > >               }
> > >               break;
> > >
> > > @@ -5409,8 +5418,7 @@ static void run_state_machine(struct tcpm_port *port)
> > >                       port->send_discover = true;
> > >                       port->send_discover_prime = false;
> > >               }
> > > -             tcpm_set_state_cond(port, DR_SWAP_SEND_TIMEOUT,
> > > -                                 PD_T_SENDER_RESPONSE);
> > > +             tcpm_set_state_cond(port, DR_SWAP_SEND_TIMEOUT, sender_response_time);
> > >               break;
> > >       case DR_SWAP_ACCEPT:
> > >               tcpm_pd_send_control(port, PD_CTRL_ACCEPT, TCPC_TX_SOP);
> > > @@ -5444,7 +5452,7 @@ static void run_state_machine(struct tcpm_port *port)
> > >                       tcpm_set_state(port, ERROR_RECOVERY, 0);
> > >                       break;
> > >               }
> > > -             tcpm_set_state_cond(port, FR_SWAP_SEND_TIMEOUT, PD_T_SENDER_RESPONSE);
> > > +             tcpm_set_state_cond(port, FR_SWAP_SEND_TIMEOUT, sender_response_time);
> > >               break;
> > >       case FR_SWAP_SEND_TIMEOUT:
> > >               tcpm_set_state(port, ERROR_RECOVERY, 0);
> > > @@ -5475,8 +5483,7 @@ static void run_state_machine(struct tcpm_port *port)
> > >               break;
> > >       case PR_SWAP_SEND:
> > >               tcpm_pd_send_control(port, PD_CTRL_PR_SWAP, TCPC_TX_SOP);
> > > -             tcpm_set_state_cond(port, PR_SWAP_SEND_TIMEOUT,
> > > -                                 PD_T_SENDER_RESPONSE);
> > > +             tcpm_set_state_cond(port, PR_SWAP_SEND_TIMEOUT, sender_response_time);
> > >               break;
> > >       case PR_SWAP_SEND_TIMEOUT:
> > >               tcpm_swap_complete(port, -ETIMEDOUT);
> > > @@ -5574,8 +5581,7 @@ static void run_state_machine(struct tcpm_port *port)
> > >               break;
> > >       case VCONN_SWAP_SEND:
> > >               tcpm_pd_send_control(port, PD_CTRL_VCONN_SWAP, TCPC_TX_SOP);
> > > -             tcpm_set_state(port, VCONN_SWAP_SEND_TIMEOUT,
> > > -                            PD_T_SENDER_RESPONSE);
> > > +             tcpm_set_state(port, VCONN_SWAP_SEND_TIMEOUT, sender_response_time);
> > >               break;
> > >       case VCONN_SWAP_SEND_TIMEOUT:
> > >               tcpm_swap_complete(port, -ETIMEDOUT);
> > > @@ -5656,23 +5662,21 @@ static void run_state_machine(struct tcpm_port *port)
> > >               break;
> > >       case GET_STATUS_SEND:
> > >               tcpm_pd_send_control(port, PD_CTRL_GET_STATUS, TCPC_TX_SOP);
> > > -             tcpm_set_state(port, GET_STATUS_SEND_TIMEOUT,
> > > -                            PD_T_SENDER_RESPONSE);
> > > +             tcpm_set_state(port, GET_STATUS_SEND_TIMEOUT, sender_response_time);
> > >               break;
> > >       case GET_STATUS_SEND_TIMEOUT:
> > >               tcpm_set_state(port, ready_state(port), 0);
> > >               break;
> > >       case GET_PPS_STATUS_SEND:
> > >               tcpm_pd_send_control(port, PD_CTRL_GET_PPS_STATUS, TCPC_TX_SOP);
> > > -             tcpm_set_state(port, GET_PPS_STATUS_SEND_TIMEOUT,
> > > -                            PD_T_SENDER_RESPONSE);
> > > +             tcpm_set_state(port, GET_PPS_STATUS_SEND_TIMEOUT, sender_response_time);
> > >               break;
> > >       case GET_PPS_STATUS_SEND_TIMEOUT:
> > >               tcpm_set_state(port, ready_state(port), 0);
> > >               break;
> > >       case GET_SINK_CAP:
> > >               tcpm_pd_send_control(port, PD_CTRL_GET_SINK_CAP, TCPC_TX_SOP);
> > > -             tcpm_set_state(port, GET_SINK_CAP_TIMEOUT, PD_T_SENDER_RESPONSE);
> > > +             tcpm_set_state(port, GET_SINK_CAP_TIMEOUT, sender_response_time);
> > >               break;
> > >       case GET_SINK_CAP_TIMEOUT:
> > >               port->sink_cap_done = true;
> > > @@ -7109,6 +7113,18 @@ static void tcpm_fw_get_timings(struct tcpm_port *port, struct fwnode_handle *fw
> > >       ret = fwnode_property_read_u32(fwnode, "sink-bc12-completion-time-ms", &val);
> > >       if (!ret)
> > >               port->timings.snk_bc12_cmpletion_time = val;
> > > +
> > > +     ret = fwnode_property_read_u32(fwnode, "pd2-sender-response-time-ms", &val);
> > > +     if (!ret)
> > > +             port->timings.pd2_sender_response_time = val;
> > > +     else
> > > +             port->timings.pd2_sender_response_time = PD_T_PD2_SENDER_RESPONSE;
> > > +
> > > +     ret = fwnode_property_read_u32(fwnode, "pd3-sender-response-time-ms", &val);
> > > +     if (!ret)
> > > +             port->timings.pd3_sender_response_time = val;
> > > +     else
> > > +             port->timings.pd3_sender_response_time = PD_T_PD3_SENDER_RESPONSE;
> > >  }
> >
> > I can't see the whole thread, but I guess those properties were
> > okay(?).
> >
> > thanks,
> >
> > --
> > heikki





[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux