Dear Manish,
Am 17.12.21 um 17:55 schrieb Manish Chopra:
This new firmware addresses few important issues and enhancements as
mentioned below -
- Support direct invalidation of FP HSI Ver per function ID, required for
invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility
This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.
Signed-off-by: Manish Chopra <manishc@xxxxxxxxxxx>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@xxxxxxxxxxx>
Signed-off-by: Alok Prasad <palok@xxxxxxxxxxx>
Signed-off-by: Ariel Elior <aelior@xxxxxxxxxxx>
---
v1->v2:
------------
* Modified the patch such that driver to be backward compatible
with older firmware too (New fw v7.13.21.0 on linux-firmware.git
enables driver to maintain backward compatibility)
---
drivers/net/ethernet/broadcom/bnx2x/bnx2x.h | 11 +++-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c | 6 +-
.../net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h | 2 +
drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h | 3 +-
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 75 +++++++++++++++-------
5 files changed, 69 insertions(+), 28 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
index 2b06d78b..a19dd67 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
@@ -1850,6 +1850,14 @@ struct bnx2x {
/* Vxlan/Geneve related information */
u16 udp_tunnel_ports[BNX2X_UDP_PORT_MAX];
+
+#define FW_CAP_INVALIDATE_VF_FP_HSI BIT(0)
+ u32 fw_cap;
+
+ u32 fw_major;
+ u32 fw_minor;
+ u32 fw_rev;
+ u32 fw_eng;
};
/* Tx queues may be less or equal to Rx queues */ @@ -2525,5 +2533,6
@@ enum {
* Meant for implicit re-load flows.
*/
int bnx2x_vlan_reconfigure_vid(struct bnx2x *bp);
-
+int bnx2x_init_firmware(struct bnx2x *bp); void
+bnx2x_release_firmware(struct bnx2x *bp);
#endif /* bnx2x.h */
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
index 54a2334..8d36ebb 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
@@ -2365,10 +2365,8 @@ int bnx2x_compare_fw_ver(struct bnx2x *bp,
u32 load_code, bool print_err)
if (load_code != FW_MSG_CODE_DRV_LOAD_COMMON_CHIP &&
load_code != FW_MSG_CODE_DRV_LOAD_COMMON) {
/* build my FW version dword */
- u32 my_fw = (BCM_5710_FW_MAJOR_VERSION) +
- (BCM_5710_FW_MINOR_VERSION << 8) +
- (BCM_5710_FW_REVISION_VERSION << 16) +
- (BCM_5710_FW_ENGINEERING_VERSION << 24);
+ u32 my_fw = (bp->fw_major) + (bp->fw_minor << 8) +
+ (bp->fw_rev << 16) + (bp->fw_eng << 24);
/* read loaded FW from chip */
u32 loaded_fw = REG_RD(bp, XSEM_REG_PRAM); diff --git
a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h
b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h
index 3f84352..a84d015 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h
@@ -241,6 +241,8 @@
IRO[221].m2))
#define XSTORM_VF_TO_PF_OFFSET(funcId) \
(IRO[48].base + ((funcId) * IRO[48].m1))
+#define XSTORM_ETH_FUNCTION_INFO_FP_HSI_VALID_E2_OFFSET(fid)
\
+ (IRO[386].base + ((fid) * IRO[386].m1))
#define COMMON_ASM_INVALID_ASSERT_OPCODE 0x0
/* eth hsi version */
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
index 622fadc..611efee 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
@@ -3024,7 +3024,8 @@ struct afex_stats {
#define BCM_5710_FW_MAJOR_VERSION 7
#define BCM_5710_FW_MINOR_VERSION 13
-#define BCM_5710_FW_REVISION_VERSION 15
+#define BCM_5710_FW_REVISION_VERSION 21
+#define BCM_5710_FW_REVISION_VERSION_V15 15
#define BCM_5710_FW_ENGINEERING_VERSION 0
#define BCM_5710_FW_COMPILE_FLAGS 1
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index aec666e..125dafe 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -74,9 +74,19 @@
__stringify(BCM_5710_FW_MINOR_VERSION) "." \
__stringify(BCM_5710_FW_REVISION_VERSION) "." \
__stringify(BCM_5710_FW_ENGINEERING_VERSION)
+
+#define FW_FILE_VERSION_V15 \
+ __stringify(BCM_5710_FW_MAJOR_VERSION) "." \
+ __stringify(BCM_5710_FW_MINOR_VERSION) "." \
+ __stringify(BCM_5710_FW_REVISION_VERSION_V15) "." \
+ __stringify(BCM_5710_FW_ENGINEERING_VERSION)
+
#define FW_FILE_NAME_E1 "bnx2x/bnx2x-e1-" FW_FILE_VERSION
".fw"
#define FW_FILE_NAME_E1H "bnx2x/bnx2x-e1h-"
FW_FILE_VERSION ".fw"
#define FW_FILE_NAME_E2 "bnx2x/bnx2x-e2-" FW_FILE_VERSION
".fw"
+#define FW_FILE_NAME_E1_V15 "bnx2x/bnx2x-e1-"
FW_FILE_VERSION_V15 ".fw"
+#define FW_FILE_NAME_E1H_V15 "bnx2x/bnx2x-e1h-"
FW_FILE_VERSION_V15 ".fw"
+#define FW_FILE_NAME_E2_V15 "bnx2x/bnx2x-e2-"
FW_FILE_VERSION_V15 ".fw"
/* Time in jiffies before concluding the transmitter is hung */
#define TX_TIMEOUT (5*HZ)
@@ -747,9 +757,7 @@ static int bnx2x_mc_assert(struct bnx2x *bp)
CHIP_IS_E1(bp) ? "everest1" :
CHIP_IS_E1H(bp) ? "everest1h" :
CHIP_IS_E2(bp) ? "everest2" : "everest3",
- BCM_5710_FW_MAJOR_VERSION,
- BCM_5710_FW_MINOR_VERSION,
- BCM_5710_FW_REVISION_VERSION);
+ bp->fw_major, bp->fw_minor, bp->fw_rev);
return rc;
}
@@ -12308,6 +12316,15 @@ static int bnx2x_init_bp(struct bnx2x *bp)
bnx2x_read_fwinfo(bp);
+ if (IS_PF(bp)) {
+ rc = bnx2x_init_firmware(bp);
+
+ if (rc) {
+ bnx2x_free_mem_bp(bp);
+ return rc;
+ }
+ }
+
func = BP_FUNC(bp);
/* need to reset chip if undi was active */ @@ -12320,6 +12337,7 @@
static int bnx2x_init_bp(struct bnx2x *bp)
rc = bnx2x_prev_unload(bp);
if (rc) {
+ bnx2x_release_firmware(bp);
bnx2x_free_mem_bp(bp);
return rc;
}
@@ -13317,16 +13335,11 @@ static int bnx2x_check_firmware(struct
bnx2x *bp)
/* Check FW version */
offset = be32_to_cpu(fw_hdr->fw_version.offset);
fw_ver = firmware->data + offset;
- if ((fw_ver[0] != BCM_5710_FW_MAJOR_VERSION) ||
- (fw_ver[1] != BCM_5710_FW_MINOR_VERSION) ||
- (fw_ver[2] != BCM_5710_FW_REVISION_VERSION) ||
- (fw_ver[3] != BCM_5710_FW_ENGINEERING_VERSION)) {
+ if (fw_ver[0] != bp->fw_major || fw_ver[1] != bp->fw_minor ||
+ fw_ver[2] != bp->fw_rev || fw_ver[3] != bp->fw_eng) {
BNX2X_ERR("Bad FW version:%d.%d.%d.%d. Should be
%d.%d.%d.%d\n",
- fw_ver[0], fw_ver[1], fw_ver[2], fw_ver[3],
- BCM_5710_FW_MAJOR_VERSION,
- BCM_5710_FW_MINOR_VERSION,
- BCM_5710_FW_REVISION_VERSION,
- BCM_5710_FW_ENGINEERING_VERSION);
+ fw_ver[0], fw_ver[1], fw_ver[2], fw_ver[3],
+ bp->fw_major, bp->fw_minor, bp->fw_rev, bp-
fw_eng);
return -EINVAL;
}
@@ -13404,34 +13417,51 @@ static void be16_to_cpu_n(const u8
*_source, u8 *_target, u32 n)
(u8 *)bp->arr, len); \
} while (0)
-static int bnx2x_init_firmware(struct bnx2x *bp)
+int bnx2x_init_firmware(struct bnx2x *bp)
{
- const char *fw_file_name;
+ const char *fw_file_name, *fw_file_name_v15;
struct bnx2x_fw_file_hdr *fw_hdr;
int rc;
if (bp->firmware)
return 0;
- if (CHIP_IS_E1(bp))
+ if (CHIP_IS_E1(bp)) {
fw_file_name = FW_FILE_NAME_E1;
- else if (CHIP_IS_E1H(bp))
+ fw_file_name_v15 = FW_FILE_NAME_E1_V15;
+ } else if (CHIP_IS_E1H(bp)) {
fw_file_name = FW_FILE_NAME_E1H;
- else if (!CHIP_IS_E1x(bp))
+ fw_file_name_v15 = FW_FILE_NAME_E1H_V15;
+ } else if (!CHIP_IS_E1x(bp)) {
fw_file_name = FW_FILE_NAME_E2;
- else {
+ fw_file_name_v15 = FW_FILE_NAME_E2_V15;
+ } else {
BNX2X_ERR("Unsupported chip revision\n");
return -EINVAL;
}
+
BNX2X_DEV_INFO("Loading %s\n", fw_file_name);
rc = request_firmware(&bp->firmware, fw_file_name, &bp->pdev->dev);
if (rc) {
- BNX2X_ERR("Can't load firmware file %s\n",
- fw_file_name);
- goto request_firmware_exit;
+ BNX2X_DEV_INFO("Trying to load older fw %s\n", fw_file_name_v15);
+
+ /* try to load prev version */
+ rc = request_firmware(&bp->firmware, fw_file_name_v15, +&bp->pdev->dev);
+
+ if (rc)
+ goto request_firmware_exit;
+
+ bp->fw_rev = BCM_5710_FW_REVISION_VERSION_V15;
+ } else {
+ bp->fw_cap |= FW_CAP_INVALIDATE_VF_FP_HSI;
+ bp->fw_rev = BCM_5710_FW_REVISION_VERSION;
}
+ bp->fw_major = BCM_5710_FW_MAJOR_VERSION;
+ bp->fw_minor = BCM_5710_FW_MINOR_VERSION;
+ bp->fw_eng = BCM_5710_FW_ENGINEERING_VERSION;
+
rc = bnx2x_check_firmware(bp);
if (rc) {
BNX2X_ERR("Corrupt firmware file %s\n", fw_file_name); @@
-13487,7
+13517,7 @@ static int bnx2x_init_firmware(struct bnx2x *bp)
return rc;
}
-static void bnx2x_release_firmware(struct bnx2x *bp)
+void bnx2x_release_firmware(struct bnx2x *bp)
{
kfree(bp->init_ops_offsets);
kfree(bp->init_ops);
@@ -14004,6 +14034,7 @@ static int bnx2x_init_one(struct pci_dev *pdev,
return 0;
init_one_freemem:
+ bnx2x_release_firmware(bp);
bnx2x_free_mem_bp(bp);
init_one_exit:
This change was added to Linux in commit b7a49f73059f (bnx2x: Utilize
firmware 7.13.21.0) [1] to Linux v5.17-rc1, and backported to the stable
series, for example, Linux v5.10.95.
Due to CVE-2022-0847 (Dirty Pipe) [1] we updated systems from, for example,
Linux 5.10.24 to Linux v5.10.103 and noticed that the Broadcom network
devices failed to initialize.
```
[ 20.477325] bnx2 0000:02:00.0 eth0: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem c6000000, IRQ 41, node addr c8:1f:66:cf:34:45
[ 20.491782] bnx2 0000:02:00.1 eth1: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem c8000000, IRQ 42, node addr c8:1f:66:cf:34:47
[ 20.506223] bnx2 0000:03:00.0 eth2: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem ca000000, IRQ 43, node addr c8:1f:66:cf:34:49
[ 20.520644] bnx2 0000:03:00.1 eth3: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem cc000000, IRQ 44, node addr c8:1f:66:cf:34:4b
[ 20.534985] bnx2x 0000:45:00.0: msix capability found
[ 20.540342] bnx2x 0000:45:00.0: part number 394D4342-31373735-31314131-473331
[ 20.548605] bnx2x 0000:45:00.0: Direct firmware load for bnx2x/bnx2x-e1h-7.13.21.0.fw failed with error -2
[ 20.558373] bnx2x 0000:45:00.0: Direct firmware load for bnx2x/bnx2x-e1h-7.13.15.0.fw failed with error -2
[ 20.568319] bnx2x: probe of 0000:45:00.0 failed with error -2
[ 20.574148] bnx2x 0000:45:00.1: msix capability found
[ 20.579470] bnx2x 0000:45:00.1: part number 394D4342-31373735-31314131-473331
[ 20.587708] bnx2x 0000:45:00.1: Direct firmware load for bnx2x/bnx2x-e1h-7.13.21.0.fw failed with error -2
[ 20.597479] bnx2x 0000:45:00.1: Direct firmware load for bnx2x/bnx2x-e1h-7.13.15.0.fw failed with error -2
[ 20.607355] bnx2x: probe of 0000:45:00.1 failed with error -2
[ 20.613179] bnx2x 0000:46:00.0: msix capability found
[ 20.618501] bnx2x 0000:46:00.0: part number 394D4342-31373735-31314131-473331
[ 20.626805] bnx2x 0000:46:00.0: Direct firmware load for bnx2x/bnx2x-e1h-7.13.21.0.fw failed with error -2
[ 20.636580] bnx2x 0000:46:00.0: Direct firmware load for bnx2x/bnx2x-e1h-7.13.15.0.fw failed with error -2
[ 20.646453] bnx2x: probe of 0000:46:00.0 failed with error -2
[ 20.652279] bnx2x 0000:46:00.1: msix capability found
[ 20.657593] bnx2x 0000:46:00.1: part number 394D4342-31373735-31314131-473331
[ 20.665813] bnx2x 0000:46:00.1: Direct firmware load for bnx2x/bnx2x-e1h-7.13.21.0.fw failed with error -2
[ 20.675590] bnx2x 0000:46:00.1: Direct firmware load for bnx2x/bnx2x-e1h-7.13.15.0.fw failed with error -2
[ 20.685457] bnx2x: probe of 0000:46:00.1 failed with error -2
```
Due to reasons, we do not have firmware in the initrd, and the firmware files
are only the root partition in `/lib/firmware`.
Logging in using other means¹, and removing the PCI devices, and rescanning
brought the devices online.
$ echo 1 | sudo tee /sys/bus/pci/devices/0000\:{45,46}\:00.{0,1}/remove
$ echo 1 | sudo tee /sys/bus/pci/rescan
Adding the firmware files to the initrd also fixes the issue.
I didn’t bisect the change, but the refactoring of the init methods looks like the
reason for the change of behavior. As it’s not documented in the commit
message, was that intentional? I think it breaks Linux’ no regression rule, and
the commit (and follow-ups) should be reverted in Linux v5.17 and backed out
from the stable series.
