Re: [PATCH v2 net-next 1/2] bnx2x: Utilize firmware 7.13.21.0

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Dear Manish,


Am 17.12.21 um 17:55 schrieb Manish Chopra:
This new firmware addresses few important issues and enhancements
as mentioned below -

- Support direct invalidation of FP HSI Ver per function ID, required for
   invalidating FP HSI Ver prior to each VF start, as there is no VF start
- BRB hardware block parity error detection support for the driver
- Fix the FCOE underrun flow
- Fix PSOD during FCoE BFS over the NIC ports after preboot driver
- Maintains backward compatibility

This patch incorporates this new firmware 7.13.21.0 in bnx2x driver.

Signed-off-by: Manish Chopra <manishc@xxxxxxxxxxx>
Signed-off-by: Prabhakar Kushwaha <pkushwaha@xxxxxxxxxxx>
Signed-off-by: Alok Prasad <palok@xxxxxxxxxxx>
Signed-off-by: Ariel Elior <aelior@xxxxxxxxxxx>
---

v1->v2:
------------
* Modified the patch such that driver to be backward compatible
   with older firmware too (New fw v7.13.21.0 on linux-firmware.git
   enables driver to maintain backward compatibility)
---
  drivers/net/ethernet/broadcom/bnx2x/bnx2x.h        | 11 +++-
  drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c    |  6 +-
  .../net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h    |  2 +
  drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h    |  3 +-
  drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c   | 75 +++++++++++++++-------
  5 files changed, 69 insertions(+), 28 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
index 2b06d78b..a19dd67 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h
@@ -1850,6 +1850,14 @@ struct bnx2x {
/* Vxlan/Geneve related information */
  	u16 udp_tunnel_ports[BNX2X_UDP_PORT_MAX];
+
+#define FW_CAP_INVALIDATE_VF_FP_HSI	BIT(0)
+	u32 fw_cap;
+
+	u32 fw_major;
+	u32 fw_minor;
+	u32 fw_rev;
+	u32 fw_eng;
  };
/* Tx queues may be less or equal to Rx queues */
@@ -2525,5 +2533,6 @@ enum {
   * Meant for implicit re-load flows.
   */
  int bnx2x_vlan_reconfigure_vid(struct bnx2x *bp);
-
+int bnx2x_init_firmware(struct bnx2x *bp);
+void bnx2x_release_firmware(struct bnx2x *bp);
  #endif /* bnx2x.h */
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
index 54a2334..8d36ebb 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
@@ -2365,10 +2365,8 @@ int bnx2x_compare_fw_ver(struct bnx2x *bp, u32 load_code, bool print_err)
  	if (load_code != FW_MSG_CODE_DRV_LOAD_COMMON_CHIP &&
  	    load_code != FW_MSG_CODE_DRV_LOAD_COMMON) {
  		/* build my FW version dword */
-		u32 my_fw = (BCM_5710_FW_MAJOR_VERSION) +
-			(BCM_5710_FW_MINOR_VERSION << 8) +
-			(BCM_5710_FW_REVISION_VERSION << 16) +
-			(BCM_5710_FW_ENGINEERING_VERSION << 24);
+		u32 my_fw = (bp->fw_major) + (bp->fw_minor << 8) +
+				(bp->fw_rev << 16) + (bp->fw_eng << 24);
/* read loaded FW from chip */
  		u32 loaded_fw = REG_RD(bp, XSEM_REG_PRAM);
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h
index 3f84352..a84d015 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_fw_defs.h
@@ -241,6 +241,8 @@
  	IRO[221].m2))
  #define XSTORM_VF_TO_PF_OFFSET(funcId) \
  	(IRO[48].base + ((funcId) * IRO[48].m1))
+#define XSTORM_ETH_FUNCTION_INFO_FP_HSI_VALID_E2_OFFSET(fid)	\
+	(IRO[386].base + ((fid) * IRO[386].m1))
  #define COMMON_ASM_INVALID_ASSERT_OPCODE 0x0
/* eth hsi version */
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
index 622fadc..611efee 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h
@@ -3024,7 +3024,8 @@ struct afex_stats {
#define BCM_5710_FW_MAJOR_VERSION 7
  #define BCM_5710_FW_MINOR_VERSION			13
-#define BCM_5710_FW_REVISION_VERSION		15
+#define BCM_5710_FW_REVISION_VERSION		21
+#define BCM_5710_FW_REVISION_VERSION_V15	15
  #define BCM_5710_FW_ENGINEERING_VERSION		0
  #define BCM_5710_FW_COMPILE_FLAGS			1
diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
index aec666e..125dafe 100644
--- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
+++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
@@ -74,9 +74,19 @@
  	__stringify(BCM_5710_FW_MINOR_VERSION) "."	\
  	__stringify(BCM_5710_FW_REVISION_VERSION) "."	\
  	__stringify(BCM_5710_FW_ENGINEERING_VERSION)
+
+#define FW_FILE_VERSION_V15				\
+	__stringify(BCM_5710_FW_MAJOR_VERSION) "."      \
+	__stringify(BCM_5710_FW_MINOR_VERSION) "."	\
+	__stringify(BCM_5710_FW_REVISION_VERSION_V15) "."	\
+	__stringify(BCM_5710_FW_ENGINEERING_VERSION)
+
  #define FW_FILE_NAME_E1		"bnx2x/bnx2x-e1-" FW_FILE_VERSION ".fw"
  #define FW_FILE_NAME_E1H	"bnx2x/bnx2x-e1h-" FW_FILE_VERSION ".fw"
  #define FW_FILE_NAME_E2		"bnx2x/bnx2x-e2-" FW_FILE_VERSION ".fw"
+#define FW_FILE_NAME_E1_V15	"bnx2x/bnx2x-e1-" FW_FILE_VERSION_V15 ".fw"
+#define FW_FILE_NAME_E1H_V15	"bnx2x/bnx2x-e1h-" FW_FILE_VERSION_V15 ".fw"
+#define FW_FILE_NAME_E2_V15	"bnx2x/bnx2x-e2-" FW_FILE_VERSION_V15 ".fw"
/* Time in jiffies before concluding the transmitter is hung */
  #define TX_TIMEOUT		(5*HZ)
@@ -747,9 +757,7 @@ static int bnx2x_mc_assert(struct bnx2x *bp)
  		  CHIP_IS_E1(bp) ? "everest1" :
  		  CHIP_IS_E1H(bp) ? "everest1h" :
  		  CHIP_IS_E2(bp) ? "everest2" : "everest3",
-		  BCM_5710_FW_MAJOR_VERSION,
-		  BCM_5710_FW_MINOR_VERSION,
-		  BCM_5710_FW_REVISION_VERSION);
+		  bp->fw_major, bp->fw_minor, bp->fw_rev);
return rc;
  }
@@ -12308,6 +12316,15 @@ static int bnx2x_init_bp(struct bnx2x *bp)
bnx2x_read_fwinfo(bp); + if (IS_PF(bp)) {
+		rc = bnx2x_init_firmware(bp);
+
+		if (rc) {
+			bnx2x_free_mem_bp(bp);
+			return rc;
+		}
+	}
+
  	func = BP_FUNC(bp);
/* need to reset chip if undi was active */
@@ -12320,6 +12337,7 @@ static int bnx2x_init_bp(struct bnx2x *bp)
rc = bnx2x_prev_unload(bp);
  		if (rc) {
+			bnx2x_release_firmware(bp);
  			bnx2x_free_mem_bp(bp);
  			return rc;
  		}
@@ -13317,16 +13335,11 @@ static int bnx2x_check_firmware(struct bnx2x *bp)
  	/* Check FW version */
  	offset = be32_to_cpu(fw_hdr->fw_version.offset);
  	fw_ver = firmware->data + offset;
-	if ((fw_ver[0] != BCM_5710_FW_MAJOR_VERSION) ||
-	    (fw_ver[1] != BCM_5710_FW_MINOR_VERSION) ||
-	    (fw_ver[2] != BCM_5710_FW_REVISION_VERSION) ||
-	    (fw_ver[3] != BCM_5710_FW_ENGINEERING_VERSION)) {
+	if (fw_ver[0] != bp->fw_major || fw_ver[1] != bp->fw_minor ||
+	    fw_ver[2] != bp->fw_rev || fw_ver[3] != bp->fw_eng) {
  		BNX2X_ERR("Bad FW version:%d.%d.%d.%d. Should be %d.%d.%d.%d\n",
-		       fw_ver[0], fw_ver[1], fw_ver[2], fw_ver[3],
-		       BCM_5710_FW_MAJOR_VERSION,
-		       BCM_5710_FW_MINOR_VERSION,
-		       BCM_5710_FW_REVISION_VERSION,
-		       BCM_5710_FW_ENGINEERING_VERSION);
+			  fw_ver[0], fw_ver[1], fw_ver[2], fw_ver[3],
+			  bp->fw_major, bp->fw_minor, bp->fw_rev, bp->fw_eng);
  		return -EINVAL;
  	}
@@ -13404,34 +13417,51 @@ static void be16_to_cpu_n(const u8 *_source, u8 *_target, u32 n)
  	     (u8 *)bp->arr, len);					\
  } while (0)
-static int bnx2x_init_firmware(struct bnx2x *bp)
+int bnx2x_init_firmware(struct bnx2x *bp)
  {
-	const char *fw_file_name;
+	const char *fw_file_name, *fw_file_name_v15;
  	struct bnx2x_fw_file_hdr *fw_hdr;
  	int rc;
if (bp->firmware)
  		return 0;
- if (CHIP_IS_E1(bp))
+	if (CHIP_IS_E1(bp)) {
  		fw_file_name = FW_FILE_NAME_E1;
-	else if (CHIP_IS_E1H(bp))
+		fw_file_name_v15 = FW_FILE_NAME_E1_V15;
+	} else if (CHIP_IS_E1H(bp)) {
  		fw_file_name = FW_FILE_NAME_E1H;
-	else if (!CHIP_IS_E1x(bp))
+		fw_file_name_v15 = FW_FILE_NAME_E1H_V15;
+	} else if (!CHIP_IS_E1x(bp)) {
  		fw_file_name = FW_FILE_NAME_E2;
-	else {
+		fw_file_name_v15 = FW_FILE_NAME_E2_V15;
+	} else {
  		BNX2X_ERR("Unsupported chip revision\n");
  		return -EINVAL;
  	}
+
  	BNX2X_DEV_INFO("Loading %s\n", fw_file_name);
rc = request_firmware(&bp->firmware, fw_file_name, &bp->pdev->dev);
  	if (rc) {
-		BNX2X_ERR("Can't load firmware file %s\n",
-			  fw_file_name);
-		goto request_firmware_exit;
+		BNX2X_DEV_INFO("Trying to load older fw %s\n", fw_file_name_v15);
+
+		/* try to load prev version */
+		rc = request_firmware(&bp->firmware, fw_file_name_v15, &bp->pdev->dev);
+
+		if (rc)
+			goto request_firmware_exit;
+
+		bp->fw_rev = BCM_5710_FW_REVISION_VERSION_V15;
+	} else {
+		bp->fw_cap |= FW_CAP_INVALIDATE_VF_FP_HSI;
+		bp->fw_rev = BCM_5710_FW_REVISION_VERSION;
  	}
+ bp->fw_major = BCM_5710_FW_MAJOR_VERSION;
+	bp->fw_minor = BCM_5710_FW_MINOR_VERSION;
+	bp->fw_eng = BCM_5710_FW_ENGINEERING_VERSION;
+
  	rc = bnx2x_check_firmware(bp);
  	if (rc) {
  		BNX2X_ERR("Corrupt firmware file %s\n", fw_file_name);
@@ -13487,7 +13517,7 @@ static int bnx2x_init_firmware(struct bnx2x *bp)
  	return rc;
  }
-static void bnx2x_release_firmware(struct bnx2x *bp)
+void bnx2x_release_firmware(struct bnx2x *bp)
  {
  	kfree(bp->init_ops_offsets);
  	kfree(bp->init_ops);
@@ -14004,6 +14034,7 @@ static int bnx2x_init_one(struct pci_dev *pdev,
  	return 0;
init_one_freemem:
+	bnx2x_release_firmware(bp);
  	bnx2x_free_mem_bp(bp);
init_one_exit:

This change was added to Linux in commit b7a49f73059f (bnx2x: Utilize firmware 7.13.21.0) [1] to Linux v5.17-rc1, and backported to the stable series, for example, Linux v5.10.95.

Due to CVE-2022-0847 (Dirty Pipe) [1] we updated systems from, for example, Linux 5.10.24 to Linux v5.10.103 and noticed that the Broadcom network devices failed to initialize.

```
[ 20.477325] bnx2 0000:02:00.0 eth0: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem c6000000, IRQ 41, node addr c8:1f:66:cf:34:45 [ 20.491782] bnx2 0000:02:00.1 eth1: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem c8000000, IRQ 42, node addr c8:1f:66:cf:34:47 [ 20.506223] bnx2 0000:03:00.0 eth2: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem ca000000, IRQ 43, node addr c8:1f:66:cf:34:49 [ 20.520644] bnx2 0000:03:00.1 eth3: Broadcom NetXtreme II BCM5709 1000Base-T (C0) PCI Express found at mem cc000000, IRQ 44, node addr c8:1f:66:cf:34:4b
[   20.534985] bnx2x 0000:45:00.0: msix capability found
[ 20.540342] bnx2x 0000:45:00.0: part number 394D4342-31373735-31314131-473331 [ 20.548605] bnx2x 0000:45:00.0: Direct firmware load for bnx2x/bnx2x-e1h-7.13.21.0.fw failed with error -2 [ 20.558373] bnx2x 0000:45:00.0: Direct firmware load for bnx2x/bnx2x-e1h-7.13.15.0.fw failed with error -2
[   20.568319] bnx2x: probe of 0000:45:00.0 failed with error -2
[   20.574148] bnx2x 0000:45:00.1: msix capability found
[ 20.579470] bnx2x 0000:45:00.1: part number 394D4342-31373735-31314131-473331 [ 20.587708] bnx2x 0000:45:00.1: Direct firmware load for bnx2x/bnx2x-e1h-7.13.21.0.fw failed with error -2 [ 20.597479] bnx2x 0000:45:00.1: Direct firmware load for bnx2x/bnx2x-e1h-7.13.15.0.fw failed with error -2
[   20.607355] bnx2x: probe of 0000:45:00.1 failed with error -2
[   20.613179] bnx2x 0000:46:00.0: msix capability found
[ 20.618501] bnx2x 0000:46:00.0: part number 394D4342-31373735-31314131-473331 [ 20.626805] bnx2x 0000:46:00.0: Direct firmware load for bnx2x/bnx2x-e1h-7.13.21.0.fw failed with error -2 [ 20.636580] bnx2x 0000:46:00.0: Direct firmware load for bnx2x/bnx2x-e1h-7.13.15.0.fw failed with error -2
[   20.646453] bnx2x: probe of 0000:46:00.0 failed with error -2
[   20.652279] bnx2x 0000:46:00.1: msix capability found
[ 20.657593] bnx2x 0000:46:00.1: part number 394D4342-31373735-31314131-473331 [ 20.665813] bnx2x 0000:46:00.1: Direct firmware load for bnx2x/bnx2x-e1h-7.13.21.0.fw failed with error -2 [ 20.675590] bnx2x 0000:46:00.1: Direct firmware load for bnx2x/bnx2x-e1h-7.13.15.0.fw failed with error -2
[   20.685457] bnx2x: probe of 0000:46:00.1 failed with error -2
```

Due to reasons, we do not have firmware in the initrd, and the firmware files are only the root partition in `/lib/firmware`.

Logging in using other means¹, and removing the PCI devices, and rescanning brought the devices online.

    $ echo 1 | sudo tee /sys/bus/pci/devices/0000\:{45,46}\:00.{0,1}/remove
    $ echo 1 | sudo tee /sys/bus/pci/rescan

Adding the firmware files to the initrd also fixes the issue.

I didn’t bisect the change, but the refactoring of the init methods looks like the reason for the change of behavior. As it’s not documented in the commit message, was that intentional? I think it breaks Linux’ no regression rule, and the commit (and follow-ups) should be reverted in Linux v5.17 and backed out from the stable series.


Kind regards,

Paul


¹ Why can’t even without proper firmware, the card at least initialize to have a network connection even if it’s degraded?



[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux