RE: [PATCH] pinctrl/amd: Remove the default de-bounce time

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



In the function amd_gpio_irq_enable and amd_gpio_direction_input, remove the code which is setting the default de-bounce time to 2.75ms.

The driver code shall use the same settings as specified in BIOS.
Any default assignment impacts TouchPad behaviour when the LevelTrig is set to EDGE FALLING.

Reviewed-by:  Ken Xue <Ken.Xue@xxxxxxx>
Signed-off-by: Nitesh Kumar Agrawal <Nitesh-kumar.Agrawal@xxxxxxx>
---
 drivers/pinctrl/pinctrl-amd.c | 20 +-------------------
 1 file changed, 1 insertion(+), 19 deletions(-)

diff --git a/drivers/pinctrl/pinctrl-amd.c b/drivers/pinctrl/pinctrl-amd.c index 634b4d3..828148d 100644
--- a/drivers/pinctrl/pinctrl-amd.c
+++ b/drivers/pinctrl/pinctrl-amd.c
@@ -43,16 +43,6 @@ static int amd_gpio_direction_input(struct gpio_chip *gc, unsigned offset)
 
 	spin_lock_irqsave(&gpio_dev->lock, flags);
 	pin_reg = readl(gpio_dev->base + offset * 4);
-	/*
-	 * Suppose BIOS or Bootloader sets specific debounce for the
-	 * GPIO. if not, set debounce to be  2.75ms and remove glitch.
-	*/
-	if ((pin_reg & DB_TMR_OUT_MASK) == 0) {
-		pin_reg |= 0xf;
-		pin_reg |= BIT(DB_TMR_OUT_UNIT_OFF);
-		pin_reg |= DB_TYPE_REMOVE_GLITCH << DB_CNTRL_OFF;
-		pin_reg &= ~BIT(DB_TMR_LARGE_OFF);
-	}
 
 	pin_reg &= ~BIT(OUTPUT_ENABLE_OFF);
 	writel(pin_reg, gpio_dev->base + offset * 4); @@ -326,15 +316,7 @@ static void amd_gpio_irq_enable(struct irq_data *d)
 
 	spin_lock_irqsave(&gpio_dev->lock, flags);
 	pin_reg = readl(gpio_dev->base + (d->hwirq)*4);
-	/*
-		Suppose BIOS or Bootloader sets specific debounce for the
-		GPIO. if not, set debounce to be  2.75ms.
-	*/
-	if ((pin_reg & DB_TMR_OUT_MASK) == 0) {
-		pin_reg |= 0xf;
-		pin_reg |= BIT(DB_TMR_OUT_UNIT_OFF);
-		pin_reg &= ~BIT(DB_TMR_LARGE_OFF);
-	}
+
 	pin_reg |= BIT(INTERRUPT_ENABLE_OFF);
 	pin_reg |= BIT(INTERRUPT_MASK_OFF);
 	writel(pin_reg, gpio_dev->base + (d->hwirq)*4);
--
2.7.4


Any comments on the above patch

Thanks
Regards
Nitesh
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Kernel]     [Kernel Development Newbies]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Hiking]     [Linux Kernel]     [Linux SCSI]