Hi Felipe,
On ven., août 21 2015, Gregory CLEMENT <gregory.clement@xxxxxxxxxxxxxxxxxx> wrote:
>> According to the OTG specification after a timeout of
>> OTG_TIME_A_WAIT_VRISE (the maximum value is 100ms) the driver must
>> move from the state a_wait_vrise to the state a_wait_bcon. However,
>> the dsps version of musb does not handle this case.
>>
>> Without it, the driver could remain stuck in the a_wait_vrise. It can
>> be reproduce with the following steps:
>>
>> 1) Boot a board with no USB adapter inserted
>> 2) Insert an empty OTG adapter
>> 3) Wait 2 seconds then remove the OTG adapter
>> 4) The unit is now stuck in host mode, the VBUS switch is latched on
>> and the ID pin is no longer polled.
>>
>> The only way to exit this state was to insert a OTG adapter with an
>> USB device connected. Until this, the usb device mode was not
>> available.
>>
>> It was tested on a AM35x based board.
>>
>> CC: <stable@xxxxxxxxxxxxxxx>
>> Signed-off-by: Gregory CLEMENT <gregory.clement@xxxxxxxxxxxxxxxxxx>
>> ---
>> drivers/usb/musb/musb_dsps.c | 14 +++++++++++++-
>> 1 file changed, 13 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
>> index 65d931a..2d22683 100644
>> --- a/drivers/usb/musb/musb_dsps.c
>> +++ b/drivers/usb/musb/musb_dsps.c
>> @@ -145,6 +145,7 @@ struct dsps_glue {
>> struct timer_list timer; /* otg_workaround timer */
>> unsigned long last_timer; /* last timer data for each instance */
>> bool sw_babble_enabled;
>> + int otg_state_a_wait_vrise_timeout;
>>
>> struct dsps_context context;
>> struct debugfs_regset32 regset;
>> @@ -268,9 +269,18 @@ static void otg_timer(unsigned long _musb)
>>
>> spin_lock_irqsave(&musb->lock, flags);
>> switch (musb->xceiv->otg->state) {
>> + case OTG_STATE_A_WAIT_VRISE:
>> + if ((glue->otg_state_a_wait_vrise_timeout)) {
>> + musb->xceiv->otg->state = OTG_STATE_A_WAIT_BCON;
>> + musb->is_active = 0;
>> + }
>> + mod_timer(&glue->timer, jiffies +
>> + msecs_to_jiffies(OTG_TIME_A_WAIT_VRISE));
>
> After more test on more USB drive, it seems that for some of them
> OTG_TIME_A_WAIT_VRISE is too short. 200ms seems better. It is
> disturbing because according to the OTG specification the maximum
> is 100ms, however I am not so surprised that USB device maker don't
> follow it.
So after many tests on different devices, 200ms is enough for most of
them, but for one, 2000ms (2s) was needed!
I see several option:
- adding a sysfs entry to setup the time
- adding a debugs entry entry
- adding configuration option in menuconfig
- using 2000ms and hopping it was enough for everyone
My preference would go to the first option, what is your opinion?
Thanks,
Gregory
>
>
>> + break;
>> case OTG_STATE_A_WAIT_BCON:
>> dsps_writeb(musb->mregs, MUSB_DEVCTL, 0);
>> skip_session = 1;
>> + glue->otg_state_a_wait_vrise_timeout = 0;
>> /* fall */
>>
>> case OTG_STATE_A_IDLE:
>> @@ -359,7 +369,9 @@ static irqreturn_t dsps_interrupt(int irq, void *hci)
>> MUSB_HST_MODE(musb);
>> musb->xceiv->otg->default_a = 1;
>> musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
>> - del_timer(&glue->timer);
>> + glue->otg_state_a_wait_vrise_timeout = 1;
>> + mod_timer(&glue->timer, jiffies +
>> + msecs_to_jiffies(OTG_TIME_A_WAIT_VRISE));
>> } else {
>> musb->is_active = 0;
>> MUSB_DEV_MODE(musb);
>>
>
>
> --
> Gregory Clement, Free Electrons
> Kernel, drivers, real-time and embedded Linux
> development, consulting, training and support.
> http://free-electrons.com
> --
> To unsubscribe from this list: send the line "unsubscribe linux-usb" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe stable" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html